Hire the best freelance Impedance Control expert designers for your company

Creative engineer with 11+ years of industry experience. Experience in circuit design, simulation, schematic capture, PCB layout, firmware development, 3D modeling and electronic manufacturing.

Creative engineer with 11+ years of industry experience. Experience in circuit design, simulation, schematic capture, PCB layout, firmware development, 3D modeling and electronic manufacturing.

I offer a complete PCB design service, managed by a team of experienced engineers. I take care of all the critical stages to ensure that your design is not only functional, but also optimized for prod... Read more

I offer a complete PCB design service, managed by a team of experienced engineers. I take care of all the critical stages to ensure that your design is not only functional, but also optimized for production and for the best electrical performance. I transform your Electrical Diagram into a production - ready PCB with guaranteed quality and cost optimization. Complex layouts (High-Speed, RF, Multi-Layer) Thanks to a well-established project management process, I act as your single point of contact. I manage the entire workflow, from receiving your design to delivering the complete Gerber files, centroids, and BOM. Dedicated Project Management: I act as your single point of contact. I take care of detailed requirements gathering, technical specification translation, and workflow management, saving you time and ensuring clear communication. Design for Manufacturing (DFM) Optimization: Each layout is rigorously checked to ensure it meets manufacturing standards. This means fewer errors, lower costs, and faster delivery times from your manufacturing company. Quality Engineering and Analysis: I perform Design Rule Checks (DRC) and 3D checks for clearance, preventing costly assembly errors and mechanical issues in advance. Professional Standard Delivery: I will provide you with a complete, universal production package that is accepted by all PCB factories worldwide.

I design medical-grade PCBs for EEG, biosensor and wearable devices - from blank schematic to a validated, manufacturable board. Most of my work sits where sub-microvolt analog meets high-speed digit... Read more

I design medical-grade PCBs for EEG, biosensor and wearable devices - from blank schematic to a validated, manufacturable board. Most of my work sits where sub-microvolt analog meets high-speed digital. I have shipped 8-channel EEG acquisition hardware built around the TI ADS1299 (electrode front end, RLD/CMRR design, shielding and ground-plane strategy that protects a 1 uV signal), a next-generation health smartwatch (nRF5340, MAX86150 ECG/PPG/SpO2, BQ51003 wireless charging, ADP5360 PMIC), and a 4-layer impedance-controlled carrier board for a handheld dermatology imaging device (NXP i.MX6UL SoM, MIPI CSI/DSI, USB 2.0, LTE/Wi-Fi/GPS). What I do for clients: - Schematic capture and multi-layer PCB layout in Altium Designer and KiCad - Biosignal analog front ends: EEG, ECG, EMG, PPG, SpO2 (ADS1299, ADS1292, MAX86150, AD8232) - High-speed and mixed-signal layout: stack-up design, impedance control, signal and power integrity, EMI/EMC-aware routing - Wearable and battery-powered design: PMIC selection, fuel gauging (MAX17055), microamp sleep budgets, wireless charging - Design for manufacturing: BOM development, component sourcing, fabrication and assembly outputs, DFM review - Firmware bring-up and debug: STM32, nRF52/nRF5340, ESP32, bare-metal C/C++, SPI/I2C/BLE, JTAG and logic analyzer work Background: BS in Electrical Engineering from COMSATS University Islamabad, Altium-certified, and over two years leading PCB and embedded hardware teams at medical device companies, including design and documentation work aimed at FDA and regulatory compliance. I am comfortable owning a board end to end or dropping into an existing design for review, respins and debugging. Clear documentation, revision history and honest timelines come standard.

I’m a Hardware Engineer with 2+ years of experience in PCB design and manufacturing release processes. I specialize in: • Mixed-signal and high-voltage boards • Stack-up definition and panelization r... Read more

I’m a Hardware Engineer with 2+ years of experience in PCB design and manufacturing release processes. I specialize in: • Mixed-signal and high-voltage boards • Stack-up definition and panelization review • Full DFM validation • BOM and Pick & Place generation • PCB bring-up and bench validation My focus is not just layout — I ensure designs are manufacturing-ready and validated before production. I work primarily with Altium Designer and have completed advanced PCB development courses at Fedevel Academy.

Hardware Design Engineer specializing in High-Speed Digital, Power Electronics, and complex PCB layouts (up to 6-layer HDI). Proven ability to architect commercial-grade systems from schematic capture... Read more

Hardware Design Engineer specializing in High-Speed Digital, Power Electronics, and complex PCB layouts (up to 6-layer HDI). Proven ability to architect commercial-grade systems from schematic capture to routing of impedance-controlled buses (PCIe, USB 3.0, Gigabit Ethernet). Adept at component-level hardware diagnostics, board bring-up, and SMD rework.

I am a PCB Designer specializing in high-speed and multilayer PCB design, with hands-on experience in transforming complex electronic concepts into reliable, manufacturable hardware. My expertise incl... Read more

I am a PCB Designer specializing in high-speed and multilayer PCB design, with hands-on experience in transforming complex electronic concepts into reliable, manufacturable hardware. My expertise includes schematic capture, signal integrity, power distribution, impedance-controlled routing, and design optimization using Altium Designer. I am committed to delivering high-quality PCB solutions by combining technical precision, attention to detail, and continuous learning.

PCB Design Engineer with over 8 years of experience with strong expertise in multilayer, high-speed, and mixed-signal board design. Skilled in tools such as Cadence Allegro 17.2 X, OrCAD Capture. Pr... Read more

PCB Design Engineer with over 8 years of experience with strong expertise in multilayer, high-speed, and mixed-signal board design. Skilled in tools such as Cadence Allegro 17.2 X, OrCAD Capture. Proficient in schematic capture, component placement, routing, and DFM/DFT compliance. Hands-on experience in ATE boards, test interface boards, and industrial control PCBs. Strong understanding of signal integrity, impedance control, and thermal management. Committed to delivering reliable, manufacturable designs that meet quality and timeline requirements.

I am a dedicated Robotics Engineer and Electronics Technician with around 7 years of professional experience specializing in hardware development and embedded systems. My core expertise lies in high-s... Read more

I am a dedicated Robotics Engineer and Electronics Technician with around 7 years of professional experience specializing in hardware development and embedded systems. My core expertise lies in high-speed digital design, multi-layer PCB layout, and ensuring absolute signal integrity in complex hardware environments. Over the years, I have successfully transformed conceptual schematics into reliable, production-ready hardware products. Core Expertise: PCB Design & Layout: Advanced multi-layer stackups, rigid-flex, and high-density interconnects. Signal & Power Integrity: Impedance control, differential pair routing, noise reduction, and decoupling optimization. Hardware Engineering: Component selection, schematic capture, prototyping, and hardware-in-the-loop testing. I thrive on solving intricate hardware bugs and optimizing electrical performance. Whether you need a brand-new electronic product designed from scratch or an existing board optimized for manufacturing, I am here to deliver industry-standard solutions. ۳. Experience Job Title: Senior Hardware Development Engineer / Robotics Engineer Description: Spearheaded the design and development of complex, multi-layer PCBs for robotic and embedded systems. Managed full-lifecycle hardware development including component sourcing, schematic design, layered stackups, and rigorous signal integrity verification. Successfully resolved critical manufacturing and design bugs (such as net conflicts, EMI issues, and impedance mismatches) to ensure stable product rollouts.

Twelve years experience in progressive positions as a high-tech hardware/product design engineer. Successfully brought 30 new digital communication products (100+ SKUs) to market. Experience across... Read more

Twelve years experience in progressive positions as a high-tech hardware/product design engineer. Successfully brought 30 new digital communication products (100+ SKUs) to market. Experience across the full development cycle: - Product definition - System architecture - Component selection - Circuit design - Schematic capture - PCB layout - Bring up, testing and design verification - System integration - Debugging and troubleshooting - NPI engineering and design optimization - Manufacturing support Consistently delivered designs to enable truly world beating products such as a wireless motion sensor 55% smaller and 80 Watt block up-converter 60% smaller than their closest competitors, and first to market Thunderbolt 3 machine vision camera. Major design experience with: - Digital design up to 40 Gbps - RF design up to 2.4 GHz - Ethernet up to 10 Gbps - USB-C - Wi-Fi - Thunderbolt 3 - Zigbee - IOT - FPGAs - Ultra low power (uA) devices - Image sensors and many other sensors - Power Supplies - Signal integrity issues and impedance-controlled design - Design for EMC to ultra strict MIL-461 standard - FCC, CE and US military certifications - Satellite communication systems and products - SMT and manual assembly and rework - Automated test design - Advanced test equipment Proven ability to lead projects to successful conclusion, build rapport and drive communication amongst diverse stakeholders, and author first-class formal technical documents.

Welcome to my profile. Following are my key expertise: 1. Over 10 years of experience in electronics circuit design, PCB design, Layout specializing in analog, digital and mixed signal systems. Specia... Read more

Welcome to my profile. Following are my key expertise: 1. Over 10 years of experience in electronics circuit design, PCB design, Layout specializing in analog, digital and mixed signal systems. Special Mastery in ALTIUM. Executed more than 500 projects 2. Proficient in using industry-standard design tools such as Altium Designer, EAGLE, KICAD, EASYEDA and PROTEUS, ensuring accurate and efficient circuit development. 3. IPC Certified Symbols and footprints Creation, High Speed PCB Design upto 5GHz 4. Multilayer PCB Design experience upto 32 Layers, Impedance Control, Length Matching, Antenna Tuning, Blind Vias, Buried Vias, Through Hole Vias 5. DFX(Design for Excellence) - DFA, DFM and DFT. First Time Right PCB - 98% 6. Compact PCB Design, Signal Integrity, Power Integrity, Single Sided, Double sided placement 7. Design Verification through Design Checklists ensuring robust, reliable and quality design 8. Applications- IOT, Consumer, Medical, Industrial, Defense etc 9. Microcontroller Interfacing - STM32, STM8S, ESP32, ESP8266, NXP, TI chipsets etc 10. Wireless Products, Battery Operated, Low Power, Low cost 11. Design Optimization - Could optimize design of any product by at least 25% 12. Design for Quality, Design Review 13. PCB Prototyping, Contract Manufacturing 14. Firmware Development - ARDUINO, C, C++ etc 15. Enclosure Design, 3D Printing, Sheet Metal, 16. Production Support 17. EMI EMC Compliant Design - RE, EMHF, Surge, EFT, Burst, Impulse, 35KV 18. Standards Experience - UL, CISPER, CE, Please contact me if you would like to develop a robust and reliable product If you are looking to bring your idea to life, contact me :)

I'm an electronics engineer specializing in analog and mixed-signal PCB design, taking boards from schematic capture through controlled-impedance layout to fabrication. I recently earned my BS in Ele... Read more

I'm an electronics engineer specializing in analog and mixed-signal PCB design, taking boards from schematic capture through controlled-impedance layout to fabrication. I recently earned my BS in Electronics Engineering from the Technical University of Cluj-Napoca, where I built my foundation on the hardware side of the stack: multi-layer PCB design, fine-pitch BGA and high-speed differential routing, power delivery, and analog design down to the IC level. Across university projects, national competitions, and research, I've designed a range of boards — including a 4-layer software-defined-radio front-end built around a 16-bit, 200 MSPS ADC, a 6-layer MPU system board carrying high-speed interfaces (Gigabit Ethernet, MIPI CSI, USB), and several STM32-based systems. That work has given me hands-on experience with the details that make high-speed boards actually work: impedance control, differential-pair length matching, clean power delivery, and design-for-manufacturability. I've also worked on the analog side at the circuit level. In a research role in analog IC design, I designed and validated op-amps, filters, and a programmable-gain amplifier against strict specifications for gain, bandwidth, phase margin, THD, and stability, running PVT, Monte Carlo, noise, and stability analyses in Cadence ADE-XL and LTSpice. More recently, I completed a hardware design internship at Analog Devices. I'm comfortable across the full flow rather than one slice of it , schematic, layout, and the fabrication and assembly outputs (Gerbers, BOM, pick-and-place), plus the firmware and analysis to bring a board up and characterize it on the bench. What I enjoy most is the point where careful layout meets real signal and power-integrity constraints, and turning a schematic into something that manufactures cleanly and works. I've tested that under pressure, too: I've placed in several national engineering competitions, including one where I designed a complete 4-layer PCB, from schematic to fabrication files, within a strict 4-hour limit. Tools and technologies I work with: PCB & EDA: Altium Designer, KiCad, Cadence Allegro Analog & simulation: Cadence ADE-XL, LTSpice Firmware & analysis: C, C++, Python, MATLAB, Assembly Also: STM32 development, DSP, and 3D printing (FreeCAD, Bambu Studio) Having just completed my degree, I'm available immediately and open to roles in PCB design, analog and mixed-signal hardware, and embedded systems, on-site or remote. If that lines up with what your team is building, I'd love to connect, I'm always happy to talk hardware and share my portfolio

A reliable electronics engineer and PCB designer with 15+ years of experience (trusted by clients worldwide) in PCB design, schematic capture, hardware development, and manufacturing support. I delive... Read more

A reliable electronics engineer and PCB designer with 15+ years of experience (trusted by clients worldwide) in PCB design, schematic capture, hardware development, and manufacturing support. I deliver production-ready designs that reduce risk, shorten development cycles, and work right the first time. My PCB designs are not only functional but manufacture able, testable, and scalable. With my 100% Job Success Score, I help clients turn ideas into robust, production-ready electronic products. My specialization is in circuit design, schematic capture, multilayer PCB layout, embedded systems, power electronics, RF and microwave circuits and analog circuits. I can do design reviews, hardware development, hardware debugging, reverse engineering, design optimization, troubleshooting and ensure your project is delivered with precision and attention to detail. ⭐ Core Expertise ⭐ ✅ Multilayer PCB designing ✅ PCB design with high speed interfaces, such as LVDS, HS-CAN, CAN FD, RS-422, RS-485, USB 3.0, FPGA high speed SerDes, PCIe, LVPECL, LPDDR4 clock, HDMI ✅ High power PCB design up to 4 layers, 3.2 KW, 320V output at 10A load current ✅ Design for Manufacturing (DFM) & Design for Assembly (DFA) using JLC PCB and PCB way services ✅ EMC / EMI aware PCB design practice using industry standards such as IPC-2221, IEC61188, DO-254 ✅ JLC PCB and LCSC parts selection, finding in-stock components, creating BOM with updated and available parts, finding alternate parts with similar technical specifications ✅ Generating Gerber files, NC Drill files, CPL files, BOM files for production, prototyping & mass manufacturing ✅ Schematic and PCB design review ✅ Circuit Designing, analog, digital, RF, microwave, embedded, high power circuit designing ✅ Circuit Simulation & Analysis ✅ Microcontroller Programming in C language ✅ Reverse engineering from given Gerber files, PCB images, BOM ✅ Problem solving, hardware development, troubleshooting, hardware debugging, design optimization for power, thermal, mechanicals constraints ⭐ PCB Design Software ⭐ ✅ Altium Designer v24 ✅ KICAD v9 ✅ DIP TRACE ✅ EasyEDA ⭐ Circuit Simulation Software ⭐ ✅ LTspice ✅ Proteus ✅ Multisim ✅ Keysight ADS ✅ Ansys HFSS ⭐ Programming ⭐ ✅ MPLAB X IDE ✅ C Language ✅ MATLAB SIMULINK ⭐ 3D Mechanical Design ⭐ ✅ SolidWorks ✅ PTC Creo ✅ Flow Therm ⭐ Power & analog circuit Projects ⭐ Power electronics, op-amp circuits, ADC/DAC interfaces, signal conditioning, piezo electric transducer driver, flyback converter, buck boost converter, laser diode driver, LED light driver, constant current and PWM control of LED lights, Switch Mode Power Supply (SMPS) design, linear power supply design, switching transformer magnetics design, AC load control using TRIAC, DC load control using SCR, H-Bridge driver for BLDC motor control using high power MOSFETS, gate driver circuit, multivibrator circuit using 555 timer, counter circuits, relay control, IGBT circuit for DC to AC inverter, bridge rectifier circuit for AC to DC converter ⭐ Industrial Projects ⭐ Temperature, humidity, weight, pressure sensors circuit design for instrumentation electronics, data logging, real time telemetry monitoring, signal conditioning circuit, feedback control circuits, robotics and actuator control, solenoid valve for flow control, PLC, DCS, SCADA for industrial automation, ⭐ RF Projects ⭐ X-Band and S-Band microwave RF power amplifier using GaN and GaAs devices, preamplifier, Directional coupler, band pass filter, Wilkinson divider, diplexer, microstrip transmission lines impedance matching, Low Noise Amplifier (LNA), mixer, microstrip patch antenna, electronic beam steering T/R modules, I/Q modulator, phased array circuits ⭐ Audio Projects ⭐ Audio Electronics: Amplifiers, filters, DSP-based audio processing, low-noise analog design, analog crossover network, equalizer, stereo and mono dual channel amplifier, phono preamplifier, hydrophone amplifier, MEMS based microphone array design, electret microphone amplifier, CODEC, RCA to XLR converter, phantom power supply, audio power amplifier for 8 and 4 ohm loud speakers, ⭐ Digital Electronics Projects ⭐ Digital logic circuits using discrete ICs, sequential circuit, NAND Flash memory circuit, mixed signal circuit using RF transceiver blocks with SMA connectors, FMC HPC connectors, high speed signaling with FPGA Actel, Xilinx, DSP controller from microchip, microcontrollers from Silabs, PIC, ATMEL C8051, ATMEGA, TMS320F28335, ESP32-C5, ESP32-S3, STM32, RPI, ARDUINO ⭐ Why Clients Choose Me ⭐ ✅ End-to-End Capability — from concept → schematic → PCB → firmware → prototype. ✅ High-Speed PCB Specialist —Impedance controlled routing and EMC/EMI aware designs ✅ Strong Communication — clear documentation, regular updates, and fast responses. ✅ Proven Track Record — 15+ years of hands-on design experience. ✅ Client Satisfaction — long-term ▒▒▒▒▒▒ client relationships, repeat contracts, and 5⭐⭐⭐⭐⭐ feedback

As a PCB designer my area of expertise includes High Speed PCB Layouts, Rigid/Flex/Mix Signal/RF/Embedded Systems/Analog/Control Impedance/Power PCB's expert. Schematic Capture/Bill of Materials/Rever... Read more

As a PCB designer my area of expertise includes High Speed PCB Layouts, Rigid/Flex/Mix Signal/RF/Embedded Systems/Analog/Control Impedance/Power PCB's expert. Schematic Capture/Bill of Materials/Reverse Engineering/PCB fabrication/Concept to Assembled PCB service. For PCB Designing, i use different Softwares including Allegro, Altium and Kicad. I do FPGA and Microcontrollers programming as well by using ISE suite Design and Microcontrollers IDEs. I can Simulate MCU by using Proteus.

Core Skills: - PCB / ECAD: OrCAD, Altium, PADS, schematic capture, controlled impedance, PCB constraints, BOM review, DFM/DFT, ECOs - Embedded Hardware: FPGA/SoC integration, DDR review, reset topolog... Read more

Core Skills: - PCB / ECAD: OrCAD, Altium, PADS, schematic capture, controlled impedance, PCB constraints, BOM review, DFM/DFT, ECOs - Embedded Hardware: FPGA/SoC integration, DDR review, reset topology, power sequencing, clocking, isolated I/O, sensors, motor control - Interfaces: Ethernet/IP, Ethernet, SPI, I2C, UART, RS232, USB, LVDS, MIPI, industrial I/O, cable/harness documentation - FPGA / Validation: VHDL, C/C++ firmware integration, Efinix Efinity, Vivado, Quartus, verification test benches, board bring-up, thermal/EMC/environmental testing - Lifecycle: Software ICDs, Arena PLM, SAP, CI/CD release validation, vendor coordination, component sourcing, sustaining engineering, production troubleshooting

Hello, Everyone! I am an embedded systems engineer, PCB designer, and firmware developer with over 10 years of professional experience. I provide complete, end-to-end solutions for a wide range of ele... Read more

Hello, Everyone! I am an embedded systems engineer, PCB designer, and firmware developer with over 10 years of professional experience. I provide complete, end-to-end solutions for a wide range of electronic device designs, supporting clients from initial concept and schematic design to PCB layout, prototyping, assembly, and full system testing. I have strong expertise in high-speed PCB design, including PCIe and DDR4 routing, as well as precise impedance matching for reliable performance at high frequencies. I also specialize in RF and antenna design for modern IoT devices, ensuring optimal signal integrity and system efficiency. In addition, I have deep experience in ultra-low power design, achieving microamp and sub-microamp current consumption for battery-operated and wearable systems. I specialize in firmware development for LTE-GPS-LoRa-BLE-based embedded systems (nRF52 series), including low-power optimization and high-precision sensor acquisition. My focus is on delivering robust, production-ready solutions with high reliability and performance. 🔥 Main Skills 👉Embedded Systems 👉Schematic Circuit Design(Low Power consumption Design) 👉Firmware Development(All Microcontrollers-STM32, TMS320, ESP32, FPGA, nRF52, Raspberry PI) 👉PCB Design(High speed signal routing, PCIe, DDR4, 18 multi-Layers Design, RF antenna Design,) using Altium Designer, KiCad, EasyEDA, Fusion 360(No problem in DFM-JLCPCB) 👉IoT with nRF52(BLE), LoRa(for example, SX1262), LTE(SIM card interface), GPS and other variety of sensors 🛠️Tools & Technologies: 👉 nRF5 SDK / nRF Connect SDK 👉SEGGER Embedded Studio + J-Link debugging 👉 C/C++ (bare-metal & RTOS) 👉 BLE GATT, LTE AT commanders, custom wireless protocols 👉SPI / I2C / UART / ADC integration 👉Low-noise measurement systems (nA level) 👉STM32CubeIDE, Cube MX, Keil, CCS, Arduino, ... 👉MQTT, Free RTOS, Zephyr RTOS 🚀 I can support your project from concept to production.

Product manager Professional on managing and developing new electromechanical (such as compressor base and turbofan ventilators) product by using Microsoft project software. Design SharePoint Website... Read more

Product manager Professional on managing and developing new electromechanical (such as compressor base and turbofan ventilators) product by using Microsoft project software. Design SharePoint Website and Solidwork PDM Data management Manage to create molding plastic injection parts of a product. Manage to build and installation of product prototypes by collaboration with chines company. Embedded Programming Embedded programming with graphical libraries such as LittlevGL and TouchGFX Embedded programming with RTOS such as embOS and FreeRTOS Coding ARM microcontroller in IAR and Keil IDE Coding AVR microcontroller by Codevision and Atmel studio IDE The ability of programming with Matlab, C++, C#, and Assembly languages FPGA Programming, synthesizing, simulating, implementation of the Xilinix FPGA program with Verilog language Standard knowledge about standard such as: Achieve CE for medical devices ATEX Standard: IEC 60079-0 ,IEC 60079-1, IEC 60079-11, IEC 60079-25, IEC 79-3 EMC IEC61326-1 IP Standard: IEC60529, ISO NEMA, SIL, NIST standards safety requirements for electrical equipment (IEC 61010-2-030) Web Design Designing a static and dynamic website with and without content management system (CMS) The ability of programming with PHP, HTML, CSS languages Electronic Engineering Reverse engineering electronic circuits and devices Professional on designing multi-layer analog and digital electronic board by Altium DXP Strong knowledge about signal integrity issues such as Reflation, termination, Controlled impedance, EMI, Crosstalk, Differential traces, Power distribution, High-frequency Losses lines, Short Wavelengths, Control trace temperatures Professional on signal measurement by industrial measurement tools such as Spectrum Analyzer, Oscilloscope, Function Generator, Arbitrary Waveform Generator, Tracking Generator, Soldering and Disordering Station, LRC Meter, Multimeter Soldering and assembling surface mount device (SMD) Designing switching Power Supply Instrumentation Instruments Setup and have knowledge about the concept of instrumentation equipment such as Pressure transmitter, Temperature transmitter, Recorder, Level Switch, Level Transmitter knowledge about Industrial Network such as Profibus, Foundation Fieldbus, HART and DCS Experience of working with Siemens PLC logo, S7 300/400 series Pneumatic Setup and have knowledge about pneumatic instrument and systems. Computer knowledge Setup and maintenance of computer networks (Network+) Maintenance of personal computers and servers (A+) Documentation Professional in project documentation by using Microsoft Word, Excell, Visio, and Adobe Photoshop, Coreldraw software. Analysis of materials Material analysis with SEM,TEM,BET, XRD ,VSM

I'm passionate in solving customers' problems and adding value through the skills I've gained. I believe sustainable design is a sensible design for any solution. I'm a Master in Engineering (Mechan... Read more

I'm passionate in solving customers' problems and adding value through the skills I've gained. I believe sustainable design is a sensible design for any solution. I'm a Master in Engineering (Mechanical) and has more than 5 years of experience in 3D modelling and 4 years of CAD development in Solidworks

Strong skills developed in design, manufacturing, and management through co-op work terms and club experience. Previous employment includes conception and design of industrial automation equipment fro... Read more

Strong skills developed in design, manufacturing, and management through co-op work terms and club experience. Previous employment includes conception and design of industrial automation equipment from consumer packaging to aluminum refinement.

I am product designer with passion for machine and machinery parts design. I have worked on various projects for both startups and established companies, focusing mostly on product visualisation and e... Read more

I am product designer with passion for machine and machinery parts design. I have worked on various projects for both startups and established companies, focusing mostly on product visualisation and effective results. I have worked on number of mechanical projects designing and manufacturing both as well, viz Sauce Dispenser, Coin Based Water Dispenser, Fastest Paper Plate Machine, Solenoid Engine, etc. I prefer to use Siemens NX (Unigraphics) but I am also a proficient user of AutoCAD, SolidWorks, and various CAD packages like Catia and Pro Engineer. With my extensive experience in these fields, I can deliver successful and attention grabbing visuals that will make your products stand out from your competition and get attention they deserve.

I specialize in high quality, dynamic visuals and 3D models for the architecture, construction, live events and entertainment industry. My experience in all levels of event set construction gives me k... Read more

I specialize in high quality, dynamic visuals and 3D models for the architecture, construction, live events and entertainment industry. My experience in all levels of event set construction gives me keen insight into not just the design but also the budget, materials, construction and turnaround time of your build. The result is a faster workflow and high-quality output because I understand your language and everything it takes to put an event together. My whole life and career have been dedicated to art, design, engineering and creative problem solving. Anyone who has worked in the London events industry can confidently say that they know how to solve a probem....fast!!

Highly Experienced Facade Designer | Building Envelope Specialist 🏢 | Estimator I'm a results-driven Facade Designer with over 6+ years of experience in designing and delivering complex building env... Read more

Highly Experienced Facade Designer | Building Envelope Specialist 🏢 | Estimator I'm a results-driven Facade Designer with over 6+ years of experience in designing and delivering complex building envelope solutions. I'm excited to explore remote opportunities worldwide and am available for immediate join. I am open to freelance work. ✅ Key Expertise: ▪️Facade Design & Engineering ▪️Building Envelope Solutions ▪️Estimation & Cost Management ▪️AutoCAD, Blue-beam Revu, Asana ▪️ACM/ACP Cladding, Curtainwall ▪️Fibre Cement ,Panel Cladding ▪️Unitized Systems, Tile/Stone Cladding ▪️Balustrade Railing ▪️Canopy, Skylight, Signage, Spider Glazing ▪️Semi-Unitized Systems ▪️Door, Windows, Framing, As-built Drawings ✅ Services: ▪️Facade Design & Detailing ▪️Estimation & Material Takeoff ▪️MTO/Cutting List Generation ▪️Fabrication Drawings & Tentative Orders ▪️As-built Drawings & Site Support I'm passionate about delivering innovative and sustainable facade solutions. Let's connect 📮to discuss how I can contribute to your project.🤝 🪬🧿

I'm a fresh graduate from Alexandria University with a bachelor's degree in Electromechanical Engineering. I have always been a fast learner with the ability to always come up with new ideas and solu... Read more

I'm a fresh graduate from Alexandria University with a bachelor's degree in Electromechanical Engineering. I have always been a fast learner with the ability to always come up with new ideas and solutions which drove me to pursue an engineering degree to help change the world into a better place and improve people's lives. I have worked on different projects related to the automotive, robotics, and construction fields. 1- I spent 3 years in an FSAE team from working on the fuel system, becoming the engine sub-team lead to being the chief design engineer of the team, and taking the decision to stop working on IC vehicles and start working on an FSAE EV. 2- Designing and programming a mini palletizing robot for a robotics course and manufacturing it using 3D printing technology. 3- Designing a Bionic arm where I designed and manufactured 2 prototypes using 3D printing technology (prepared the 3D printing files and printed them myself) and collected anthropometric data to support my design decisions. 4- Designing the electrical floor lighting and power plans for an educational building as a part of my Codes and Specifications of Electrical Systems course. Currently, most of my experience and knowledge is in mechanical engineering with some knowledge and experience in electrical engineering, making me suitable for projects requiring a mechanical engineer to work closely with electrical engineers for better systems integration.

Cassiopeia Technologies is a Microelectronic engineering design and consulting firms that work on the most advanced technology to offer engineering solutions and services with the best quality and com... Read more

Cassiopeia Technologies is a Microelectronic engineering design and consulting firms that work on the most advanced technology to offer engineering solutions and services with the best quality and competitive price from prototyping and manufacturing to mechatronics and renewable energy, we offer all. Our team of experts with unparalleled knowledge of software and firmware, electronics, mechatronics and robotics is ever available to attend to your requests.

I have experience in Press Tool Design :- 1.Progressive Tool 2.Draw Tool 3.Blanking & Piercing Tool 4.Transfer Tool -Draw,Trim,Cam Bending,Hemming Also I have good exposer in jig and fixture like:-... Read more

I have experience in Press Tool Design :- 1.Progressive Tool 2.Draw Tool 3.Blanking & Piercing Tool 4.Transfer Tool -Draw,Trim,Cam Bending,Hemming Also I have good exposer in jig and fixture like:- 1.Drill jig 2.Reaming Jig 3.Grinding Fixture 4.Maching Fixture 5.Welding Fixture I can work on following software :- 1.AutoCAD 2.Simens NX 3.Solidwork 4.Catia 5.Creo

I'm mechanical engineer with many years experience in modeling and simulating 3D systems , I'm looking for a freelance Job and i'm very fast using 3D softwares

I'm mechanical engineer with many years experience in modeling and simulating 3D systems , I'm looking for a freelance Job and i'm very fast using 3D softwares

3D modeling (SolidWorks) Development of technical drawings Optimization for laser cutting and bending Design of products ready for mass production

3D modeling (SolidWorks) Development of technical drawings Optimization for laser cutting and bending Design of products ready for mass production

I am passionate for designing. I have worked at several projects and they all where innovations .My design is been manufactured many times and it is been successful till now. My main stream is Mechani... Read more

I am passionate for designing. I have worked at several projects and they all where innovations .My design is been manufactured many times and it is been successful till now. My main stream is Mechanical engineering and it is my passion too. I have one patent and 4 research papers on my name. My personal interest is to make innovative projects. I always prefer to design, which can be easily be manufactured and I also work with manufacturing team to make better understanding and preferable design that can be easily manufacture and easy to use in daily life.