Hire the best freelance Electrical Distribution expert designers for your company

Born and raised in Houston, Texas. I completed high school in Conroe, Texas (Conroe High School) and was accepted to attend studies at Texas A & M University. Due to a life changing event I was unab... Read more

Born and raised in Houston, Texas. I completed high school in Conroe, Texas (Conroe High School) and was accepted to attend studies at Texas A & M University. Due to a life changing event I was unable to complete my studies there and returned home to be employed by the local electric utility company, Gulf States Utilities. Hired as a line helper in 1979, I worked in construction and maintenance of the electrical utility facilities working my way up thru the ranks from helper to apprentice lineman then to lineman 4th class then to lineman 3rd class. Once I had achieved 3rd class I was able to transition to the service department where I was trusted to work on a truck by myself unsupervised working customer service tickets and troubleshooting outages that occurred on the lines. In 1991 Gulf States Utilities was purchased by Entergy and around this time I transitioned back into the line crew in the Woodlands Network to continue construction and maintenance work on most underground but occasionally overhead lines as well. April of 1999 I transferred to the Design West group of Entergy Texas, Inc. as an Engineer Assistant and a short time later, I earned the title of Senior Engineer Assistant. I presently continue to hold that title. My present job description entails meeting with customers to determine their electrical needs, design Entergy's facilities to serve these customers, procure easements for Entergy's facilities, draft contracts and collect contributions and assemble construction job packets to hand off to our line crews to build. During the last 18 years of my employment, I have used MS Office Suite's Word, Excel, Outlook, Power Point and Access and I have used Auto CAD on a daily basis and in the past 4 years I have used GIS, Pole Foreman and other software.

Wiring Harness Design Consultant with 14+ years of experience in designing electrical distribution system schematics and harness drawings. I am also the Managing founder and Technical Lead of EDS Mast... Read more

Wiring Harness Design Consultant with 14+ years of experience in designing electrical distribution system schematics and harness drawings. I am also the Managing founder and Technical Lead of EDS Master, a consulting firm that provides electrical design engineering solutions for the automotive sector and heavy machinery industry. I leverage my expertise in electrical layouts, circuit design, and CAD engineering to deliver high-quality and cost-effective projects for clients across the globe.

A resourceful, well-read and experienced electrical engineer with a passion for delivering exceptional quality of design. Knowledge: CIBSE Guide K - Electricity in Buildings SLL Code for Lighting... Read more

A resourceful, well-read and experienced electrical engineer with a passion for delivering exceptional quality of design. Knowledge: CIBSE Guide K - Electricity in Buildings SLL Code for Lighting 2012 and CIBSE Lighting Guides (LG5, LG7, LG9, LG16) BS 5266-1, BS 5839-1 and BS 5839-6 BSRIA Guides (BG 1/2008, BG 1/2010, BG 2/2009, BG 31/2012, BG 32/2014, BG 33/2014) Spon’s Mechanical and Electrical Services Price Book 2015 University of Oxford Estates Services - Mechanical and Electrical Design Philosophy 9 Design philosophy documents for Bicester Village and Berkeley Group Building Services Engineering: 6th Edition Work Experience: OCSC - Intermediate Electrical Engineer Furness Green Partnership - Electrical Design Engineer Hoare Lea - Senior Technician Relevant Skills: AutoCAD Revit MEP Navisworks Bluebeam Revu Relux and DIALux Amtech ProDesign Microsoft Office

I am an Electrical Engineer specializing in -Designing of electrical systems ( lighting & power ). - Electrical load calculations and panel schedule. - Lightning protection and earthing. - Cabl... Read more

I am an Electrical Engineer specializing in -Designing of electrical systems ( lighting & power ). - Electrical load calculations and panel schedule. - Lightning protection and earthing. - Cable sizing - Power distribution (schematic & line diagram drawings) - Preparation of Bill of Quantities. Low voltage system services - CCTV systems - Audio system - Fire detection and alarm systems

Electrical Designer specialized in 2D/3D electrical panel design in SolidWorks Electrical, with a background in mechatronics and industrial automation. I design and size control panels and Motor Contr... Read more

Electrical Designer specialized in 2D/3D electrical panel design in SolidWorks Electrical, with a background in mechatronics and industrial automation. I design and size control panels and Motor Control Centers (MCC) with capacitor banks, delivering schematics, panel layouts and BOMs that assembly teams build from, in compliance with NBR 5410. I led my company's migration from legacy CAD to SolidWorks Electrical, cutting assembly errors by 25% and saving 20% in material costs through BOM optimization. Experienced with Siemens and Danfoss VFDs and Siemens and Weidmuller PLCs, and used to remote, asynchronous work with clear communication. Based in Brazil (GMT-3), with good overlap for US and European working hours.

Electrical technologist with a background in commercial and industrial electrical installations with 10+ years of design and estimation experience in power and renewable energy sector including in dep... Read more

Electrical technologist with a background in commercial and industrial electrical installations with 10+ years of design and estimation experience in power and renewable energy sector including in depth knowledge of preparation of conceptual and detailed estimation and design drawings of power plant, electrical distribution system and plant

Professional Engineer with a focus on MEP/Transportation. Design focus includes site electrical infrastructure, building interior electrical systems and electrical overhead and underground utility de... Read more

Professional Engineer with a focus on MEP/Transportation. Design focus includes site electrical infrastructure, building interior electrical systems and electrical overhead and underground utility design. Typical product includes construction drawings and/or calculations. Electrical design skills include the following: - Electrical equipment fit-out and specifications - Cable, conduit and equipment sizing, protection and installation - Site electrical utility layout and infrastructure - Construction cost estimation - Interior and exterior lighting design - Design compliance in accordance with the National Electric Code or National Electric Safety Code - Familiarity with public agency design standards and requirements Previous projects in the following sectors: - Parks and public spaces - Building restorations - New housing development - Streetscape and roadway improvements - Rail systems infrastructure - Electric utility infrastructure - Marinas - Decorative sign and structure lighting Based out of New York City area.

EDS Design Engineer with over 12 years of comprehensive engineering experience, specializing for the last 9 years in 3D/2D Electrical Distribution Systems (EDS) routing and packaging for Premium Autom... Read more

EDS Design Engineer with over 12 years of comprehensive engineering experience, specializing for the last 9 years in 3D/2D Electrical Distribution Systems (EDS) routing and packaging for Premium Automotive OEMs. High-level expertise in CATIA V5 (Electrical Workbench) and Capital Harness Designer. My background also includes over 3 years of rigorous structural packaging and mechanical systems integration within the Aerospace industry using Siemens NX. I bridge the gap between complex electrical architecture and physical vehicle integration, ensuring full DMU compliance, clearance management, and manufacturing-ready documentation. How I can help your project: • 3D Wire Harness Routing & Packaging: Comprehensive routing, flattening, and bundle optimization within complex environments (Automotive & Aerospace standards). • 2D Harness Manufacturing Documentation: Delivering production-ready installation drawings, schematics, and accurate Bill of Materials (BOM). • DMU & Digital Integration: Clearance management, tolerance stack-up analysis, and physical conflict resolution (clash analysis). • PLM & Data Management: Robust configuration control and release management within Teamcenter and related databases. Whether you need a quick CAD modification, 2D-to-3D conversion, or end-to-end EDS design for a new platform, I deliver industry-grade engineering solutions on time. Let's connect to discuss your project requirements.

I'm a distribution electrical design planner with hands-on experience designing and planning electrical distribution systems, including layout, routing, and system documentation. I work across AutoCAD... Read more

I'm a distribution electrical design planner with hands-on experience designing and planning electrical distribution systems, including layout, routing, and system documentation. I work across AutoCAD and GIS-based tools to produce accurate, construction-ready design packages for utility and infrastructure projects. I'm now taking on contract and freelance design work alongside my full-time role, and I bring the same attention to detail and reliability that utility-grade design work demands — clear documentation, accurate as-built alignment, and on-time delivery. I'm comfortable working independently and communicating regularly with clients to keep projects on track. Available part-time (10–20 hrs/week) for distribution design support, CAD drafting, GIS mapping, or interconnection design assistance.

Designer with analytical process, electrohydraulic and PLC controls with management, field experience in safety critical oil/gas and power control systems

Designer with analytical process, electrohydraulic and PLC controls with management, field experience in safety critical oil/gas and power control systems

Hi i,m hamed khalgh zekrabad i,m Instrumentation engineer & electrical engineer I have worked for 2 years in a structural engineering consultations firm & 4 years in Smart Intelligence Company I... Read more

Hi i,m hamed khalgh zekrabad i,m Instrumentation engineer & electrical engineer I have worked for 2 years in a structural engineering consultations firm & 4 years in Smart Intelligence Company I worked by KNX product - S_bus product - Zigbee product and ect , Services Provided: -Product Design . -Electrical/Electronics design solutions. -Electrical CAD -PLC programming -Microsoft ICDL

I've been doing 2D and 3D design work since 2009. I have experience in a wide variety of fields, such as architectural, mechanical, electrical, and many more. I primarily work with Autodesk Inventor... Read more

I've been doing 2D and 3D design work since 2009. I have experience in a wide variety of fields, such as architectural, mechanical, electrical, and many more. I primarily work with Autodesk Inventor and Autocad but I have experience with other software as well.

-Teaching Assistant at Alexandria University (Mathematics department). -Senior Electrical Engineer, graduated form Faculty of Engineering, Alexandria University with cumulative grade (Very Good With H... Read more

-Teaching Assistant at Alexandria University (Mathematics department). -Senior Electrical Engineer, graduated form Faculty of Engineering, Alexandria University with cumulative grade (Very Good With Honors ~ 84.45% )(Ranked 9th in my class). I have very good background in many fields of Electrical Engineering (e.g Electrical Distribution , Protection, Smart Home IOT and Light Current) With Good Experience In AutoCad , Dialux and Etap Soft-wares seeking to have a job as A Senior Engineer.

I am an electrical engineer specializing in power distribution, Revit MEP design, and automation systems. With experience in electrical distribution projects for commercial and industrial buildings, I... Read more

I am an electrical engineer specializing in power distribution, Revit MEP design, and automation systems. With experience in electrical distribution projects for commercial and industrial buildings, I have strong expertise in AutoCAD, DIALux, ETAP, and Revit MEP. I also have knowledge in KNX automation and Python scripting for electrical design optimization. My goal is to provide high-quality electrical solutions that align with industry standards and energy efficiency best practices.

Hi guys, I hope all is well. My name is Abdulwahab solkar. I live in Mumbai, india. i have done Bachelor Of Engineering in electrical. I have 3 years of Design Experience in Electrical Distribution Sy... Read more

Hi guys, I hope all is well. My name is Abdulwahab solkar. I live in Mumbai, india. i have done Bachelor Of Engineering in electrical. I have 3 years of Design Experience in Electrical Distribution Systems, Substation Design, Earthing and lightning protection system and lighting calculation for Industrial Plants of various nature like Oil and Gas, Petrochemical, Heavy Engineering Industries etc. I have software proficiency in Autocad, Etap and Dialux and well Familiar with relevant national and international standards codes like IS, IEC, NFPA, IEEE, ANSI, NEC, NBC, OISD etc. I am acquainted with electrical protection and metering philosophy, electrical layouts, equipment sizing and selection, hazardous area classification, Power System study including load flow, short circuit, highest motor starting, and relay co-ordination. I had worked for various clients like Oil & Natural Gas Corporation Limited, Onshore Engineering Limited, and Hindustan Petroleum Corporation Limited etc. If you have any query you can contact me at any time. Thank you for your time and consideration. Let’s find superior & economical electrical design solution.

Versatile CAD Drafter and Designer with over 25 years of production drafting experience delivering electrical, mechanical, and structural drawing packages for industrial, energy, and mega-capital faci... Read more

Versatile CAD Drafter and Designer with over 25 years of production drafting experience delivering electrical, mechanical, and structural drawing packages for industrial, energy, and mega-capital facilities. Expert in translating engineering sketches, surveys, and redlines into high-precision AutoCAD, Inventor, and Plant 3D sets. Combines electrical drafting mastery (single-lines, schematics, cable trays) with mechanical detailing (sheet metal enclosures, skids, P&IDs) and structural layouts (pad loading, matting plans, civil interfaces). Delivers a turnkey, zero-rework domestic solution with immediate US Central Time turnaround.

At Cad2D Outsourcing, we specialize in providing drafting services to electrical substation design and installation contractors. Our expertise lies in the meticulous updating of "As-built" or "As-cons... Read more

At Cad2D Outsourcing, we specialize in providing drafting services to electrical substation design and installation contractors. Our expertise lies in the meticulous updating of "As-built" or "As-constructed" drawings, paper-to-CAD conversion, as well as electrical distribution protection and control (P&C) secondary interfacing and cable scheduling for both electrical substation replacement and new connection projects. Our primary focus revolves around the critical task of keeping as-built drawings accurate and up-to-date, ensuring their alignment with the "As-constructed" stages of electrical and multi-utility projects. Our range of services encompasses comprehensive revisions to electrical schemes, wiring, and general arrangement drawings, encompassing both mechanical and electrical aspects. We also excel in graphic design for network and multi-utility drawings, effectively addressing the need for revisions arising from site mark-ups or comments following installation. Furthermore, our capabilities extend to the conversion of paper-based and raster graphic image drawings into precise, workable AutoCAD drawings. We can also overlay these drawings with vector topography and geometry, facilitating a more detailed and accurate representation of the project landscape. At Cad2D Outsourcing, we pride ourselves on offering innovative solutions that meet the evolving needs of electrical substation design and installation projects. Our commitment is to maintain the integrity and accuracy of project drawings, enhancing the overall quality and efficiency of your endeavors.

Professional Civil Engineer, BIM Lead, and Infrastructure Specialist with 10+ years of proven delivery across tier-1 oil & gas EPC facilities, heavy civil infrastructure, structural bridges, municipal... Read more

Professional Civil Engineer, BIM Lead, and Infrastructure Specialist with 10+ years of proven delivery across tier-1 oil & gas EPC facilities, heavy civil infrastructure, structural bridges, municipal road networks, and multidisciplinary commercial/residential architecture. Proven Track Record on Major Capital Projects: • Project Manager Assistant — G.E.T Technical Services on the Tilenga Upstream Oil & Gas Development Project (TotalEnergies EP Uganda, Buliisa / Albertine Graben). • Site Manager & QA/QC Manager on the $19M CNOOC Kingfisher EPC Project (China State Construction Engineering Corp - CSCEC). • Supervision on the $430M Entebbe International Airport Modernization with Dar Al-Handasah. • Site management on national bridge programs (Awoo Bridge $2.7M & Nalakasi Bridge $2.7M) under the Uganda National Roads Authority (UNRA). • Engineering surveying & CAD modeling on the $26M Nansana–Busunju highway with China WuYi. Core Technical Services & Capabilities: 1. MEP Modeling & Engineering Analysis: • Complete Mechanical, Electrical, and Plumbing (MEP) BIM coordination in Autodesk Revit MEP & Navisworks Manage. • HVAC mechanical design: air distribution duct sizing (Equal Friction and Static Regain methods), air terminals, and mechanical plant room equipment layout. • Electrical distribution modeling: primary switchboards, branch panels, cable tray routing, conduits, and circuit schedules. • Public health & plumbing: gravity drainage with sloped piping (1%–2% fall), soil/waste stacks, domestic cold & hot water distribution, and fire suppression sprinkler systems. • 3D clash detection, interference checking, and coordination reports across MEP, architectural, and structural trades. 2. Architectural & Structural BIM & FEA: • Autodesk Revit (Architecture & Structure) modeling from conceptual design up to LOD 350 construction documentation. • Detailed construction drawings, building sections, elevations, and permit packages. • Automated Bar Bending Schedules (BBS) and reinforced concrete detailing. • Structural modeling and FEA checks (Autodesk Robot Structural Analysis, ProtaStructure, and MIDAS Civil/midasGen per Eurocode 2 and BS 8110). 3. Civil Infrastructure & Earthworks: • Autodesk Civil 3D terrain modeling (TIN surfaces, LiDAR point clouds, GPS survey points). • Horizontal & vertical road alignments, superelevation transitions, custom assemblies, and 3D corridors. • Earthwork volumetric cut/fill calculation (Average End Area & Prismoidal methods) and Mass Haul Diagrams. • Gravity stormwater drainage networks and pressurized piping systems. 4. Construction QA/QC & Digital Geomatics: • Full compliance with ISO 9001 (Quality), ISO 14001 (Environment), ISO 45001 (Occupational H&S), and ISO 19650 (BIM Information Management). • Inspection & Test Plans (ITPs), material laboratory testing audits (concrete, soils, asphalt, steel), and high-precision geodetic setting out. I combine real-world site construction supervision with cutting-edge digital BIM workflows. Every drawing and 3D model is produced for practical constructability, exact tolerances, and zero clash errors. Ready to assist with your architectural plans, MEP coordination, structural calculations, civil earthworks, or 3D CAD models. Click "Invite to Project" or send a direct message to discuss your scope!

I am an Electrical Design & Power System Engineer with hands-on experience in delivering efficient, reliable, and standards-compliant electrical engineering solutions. I specialize in power system des... Read more

I am an Electrical Design & Power System Engineer with hands-on experience in delivering efficient, reliable, and standards-compliant electrical engineering solutions. I specialize in power system design, analysis, and optimization for industrial, commercial, and infrastructure projects. My core expertise includes load flow analysis, short circuit studies, relay coordination, arc flash analysis, cable sizing, and equipment selection as per international standards such as IEC, IEEE, NEC, and ANSI. I am proficient in industry-leading tools like ETAP, SKM Power Tools, and AutoCAD for detailed engineering and system modeling. I have worked on projects involving electrical distribution systems, busduct design, transformer sizing, and protection schemes, ensuring safety, reliability, and cost-effectiveness. I focus on delivering accurate designs with clear documentation, meeting both technical and client requirements.

Hi, I’m Rakesh, a professional Mechanical Designer with hands-on industry experience in **SolidWorks, Sheet Metal Design, and AutoCAD 2D**. I currently work as a designer specializing in the design a... Read more

Hi, I’m Rakesh, a professional Mechanical Designer with hands-on industry experience in **SolidWorks, Sheet Metal Design, and AutoCAD 2D**. I currently work as a designer specializing in the design and development of **electrical distribution panels and sheet metal enclosures**. My experience includes creating accurate 3D models, sheet metal components, assemblies, and detailed 2D manufacturing drawings. ### My Expertise * **SolidWorks 3D Modeling** * **SolidWorks Sheet Metal Design** * Sheet Metal Enclosures & Fabrication Parts * Electrical Distribution Panel Design * 2D Manufacturing & Fabrication Drawings * **AutoCAD 2D Drafting** * Assembly Design * Flat Pattern Development * Bend & Manufacturing Details * Design Modifications and Engineering Drawings * Converting 2D drawings into 3D models * Creating production-ready drawings I focus on creating **accurate, practical, and manufacturing-friendly designs** while considering sheet metal fabrication requirements, dimensions, bends, clearances, and assembly. Whether you need a **new sheet metal design, modification of an existing design, SolidWorks 3D model, AutoCAD 2D drawing, or manufacturing drawing**, I can help turn your requirements into professional and accurate engineering designs. I value **accuracy, clear communication, attention to detail, and meeting deadlines**. My goal is to provide designs that are not only visually correct but also practical for real-world manufacturing. **Let’s discuss your project and bring your design ideas to life.**

MEP Engineer | Skilled in HVAC, Electrical & Plumbing Systems|Skilled MEP Engineer with hands-on understanding of HVAC, electrical distribution, plumbing layouts, and fire-fighting systems, focused on... Read more

MEP Engineer | Skilled in HVAC, Electrical & Plumbing Systems|Skilled MEP Engineer with hands-on understanding of HVAC, electrical distribution, plumbing layouts, and fire-fighting systems, focused on ensuring quality, safety, and smooth project exec

I am an Electrical and Electronics Engineering professional specializing in Core Electrical Design and CAD drafting. I help clients create accurate, standard-compliant electrical layouts, SLDs, and te... Read more

I am an Electrical and Electronics Engineering professional specializing in Core Electrical Design and CAD drafting. I help clients create accurate, standard-compliant electrical layouts, SLDs, and technical documentation for residential, commercial, and renewable energy projects. Core CAD & Design Expertise: • AutoCAD Drafting: Detailed Single Line Diagrams (SLDs) and electrical floor layouts. • System Sizing: Load Estimation, Maximum Demand calculations, Transformer & DG Sizing, and Cable Selection. • Standards & Compliance: strict adherence to NBC 2016 and familiarity with basic IEC Standards. • Project Documentation: Advanced Excel for comprehensive Bill of Quantities (BoQ) preparation and cost estimation. Highlighted Projects & Accomplishments: • G+10 Premium Residential Tower: Engineered the complete electrical distribution system for a 40-unit tower (~645 kW Total Connected Load). I sized a 630 kVA Transformer and drafted all detailed SLDs and floor layouts in AutoCAD. • Utility-Scale Solar PV: Conducted technical and financial feasibility analysis for a 6.54 MW grid-connected plant using NREL SAM, optimizing system design for maximum energy yield. Whether you need precise AutoCAD drafting for project approvals, reliable load calculations, or renewable energy feasibility models, I am committed to delivering clean, professional, and highly accurate results

- Sheet Metal Design - Tooling/ Fixtures - Injection/ Blow Mold Design - Prototypes & 3D Printing Files - Electrical Distribution Equipment such as: Enclosures, Cabinets, Buss Routing, Retrofittin... Read more

- Sheet Metal Design - Tooling/ Fixtures - Injection/ Blow Mold Design - Prototypes & 3D Printing Files - Electrical Distribution Equipment such as: Enclosures, Cabinets, Buss Routing, Retrofitting, Connectors, Insulation - Electronic Enclosures & Injection Mold-able Mass Production Designs - CNC Programming, Profile Machines, Turret Punches, Mills and Lathes

Technical Abilities: • CAD Software: AutoCAD 2017 (electrical and LT), Solidworks. • Programming Software: Horner APC, Rockwell Studio5000, Connected Components Workbench, RSLogix500. • Misc.: Com... Read more

Technical Abilities: • CAD Software: AutoCAD 2017 (electrical and LT), Solidworks. • Programming Software: Horner APC, Rockwell Studio5000, Connected Components Workbench, RSLogix500. • Misc.: Commissioning, Project Management, Preventive Maintenance Program Set-up, Lockout & Tagout Program Set-up, AutoCad Standards Development. Experience: Versatility Services Inc. Brooksville, FL- Clatskanie, OR President/Owner 10/14 to Present www.versatilityservices.com Small independent system integrator • Applied engineering principles to design, modify and develop facilities, testing, machines, equipment and processes used in processing and manufacturing products. • Analyzed equipment specifications and performance requirements to determine designs to be produced by existing manufacturing and processing facilities and methods. • Analyzed engineering proposals, process requirements and related technical data pertaining to industrial machinery and equipment design. • Determined feasibility of designing new plant equipment and modifying existing facilities, considering costs, available space, time limitations, company planning and other technical and economic factors. • Provided technical information concerning manufacturing and processing techniques, materials, properties and limitations that affected long range plant and product engineering planning. • Studied engineering and technical publications to keep abreast of technological changes and developments in industry. • Program PLC using ladder logic. • Develop HMI screens. • Built custom control panels. • Provided start-up and commissioning services. • Lighting design. • Walked down existing installations and created red-line as-built drawings. • Updated existing CAD files to reflect current state of systems accurately. • Engineer and design PLC based control systems for the industrial market. • Specify instrumentation, estimating, project management, and purchasing. DcR Engineering Services Tampa, FL HT/DcR Engineering Lakeland Senior Electrical Designer 04/05 to 10/14 • Applied engineering principles to design, modify and develop facilities, testing, machines, equipment and processes used in processing and manufacturing products. • Analyzed equipment specifications and performance requirements to determine designs to be produced by existing manufacturing and processing facilities and methods. • Analyzed engineering proposals, process requirements and related technical data pertaining to industrial machinery and equipment design. • Determined feasibility of designing new plant equipment and modifying existing facilities, considering costs, available space, time limitations, company planning and other technical and economic factors. • Provided technical information concerning manufacturing and processing techniques, materials, properties and limitations that affected long range plant and product engineering planning. • Studied engineering and technical publications to keep abreast of technological changes and developments in industry. • Used computer-assisted engineering software and equipment. • Walked down existing installations and created red-line as-built drawings. • Updated existing CAD files to reflect current state of systems accurately. Engineer and design PLC based control systems for the municipal and industrial market. Specify instrumentation, estimating, project management, and purchasing. Rocha Controls Tampa, FL Electrical Designer 11/00 to 12/04 • Applied engineering principles to design, modify and develop facilities, testing, machines, equipment and processes used in processing and manufacturing products. • Analyzed equipment specifications and performance requirements to determine designs to be produced by existing manufacturing and processing facilities and methods. • Analyzed engineering proposals, process requirements and related technical data pertaining to industrial machinery and equipment design. • Determined feasibility of designing new plant equipment and modifying existing facilities, considering costs, available space, time limitations, company planning and other technical and economic factors. • Provided technical information concerning manufacturing and processing techniques, materials, properties and limitations that affected long range plant and product engineering planning. • Studied engineering and technical publications to keep abreast of technological changes and developments in industry. • Used computer-assisted engineering software and equipment. • Walked down existing installations and created red-line as-built drawings. • Updated existing CAD files to reflect current state of systems accurately. Engineer and design PLC based control systems for the municipal and industrial market. Specify instrumentation, estimating, project management, and purchasing. Central Power & Lime Brooksville, FL Electrician 02/00 to 11/00 • Repaired and maintained electrical equipment in generating station and powerhouse. • Tested defective equipment to determine cause of malfunctions and failures, using voltmeters, ammeters and related electrical testing apparatus. • Repaired and replaced equipment, such as relays, switches, supervisory controls and indicating and recording instruments. • Tested and repaired switchboard and equipment circuitry, interpreting wiring diagrams to trace and connect numerous wires carrying currents for independent functions. • Cleaned and repaired brushes, commutators, windings and bearings of generators, motors and converters. • Successfully handled converting blueprints to Autocad format. • Walked down existing installations and created red-line as-built drawings. • Updated existing CAD files to reflect current state of systems accurately. Universal Studios Escape Orlando, FL Animation/Show Control Technician 04/99 to 02/00 Troubleshoot, repair, and performed preventative maintenance on various PLC controlled systems including a rollercoater, a stunt show, and a state of the art special effects show. Worked on Allen-Bradley soft start controllers, variable frequency drives, electro-hydraulic and pnuematic equipment. Schenctady International Inc. Schenectady, NY Electrician 03/95 to 03/99 • Installed and repaired electrical systems, apparatuses and electrical and electronic components of industrial machinery and equipment. • Installed power supply wiring and conduit for newly installed machines and equipment, such as robots, conveyors and programmable controllers. • Connected power supply wires to machines and equipment and connected cables and wires between machines and equipment. • Diagnosed malfunctioning apparatuses, such as transformers, motors and lighting fixtures, using test equipment. • Tested malfunctioning machinery and discussed malfunctions with other maintenance workers. • Visually inspected and listened to machines and equipment to locate causes of malfunctions. • Dismantled machines and equipment to gain access to problem areas. • Replaced faulty electrical components of machine, such as relays, switches and motors and positioned sensing devices. • Planned layout of wiring and installed wiring, conduit and electrical apparatuses in buildings.

I am a Technical Project Designer with extensive experience in AutoCAD and practical experience in Revit. I develop technical installation projects from scratch, including electrical, plumbing/sanitar... Read more

I am a Technical Project Designer with extensive experience in AutoCAD and practical experience in Revit. I develop technical installation projects from scratch, including electrical, plumbing/sanitary, HVAC, ventilation, extraction, gas GN/GLP, and compressed air systems. My work includes technical drawings, details, isometrics, technical documentation, and 3D modeling based on engineering criteria and project requirements. I also have professional experience using Trimble Connect to identify interferences and make model modifications to resolve clashes. My main strength is my extensive practical experience in technical drafting and project development, combined with strong AutoCAD skills and hands-on Revit experience.

I am a Senior Electrical Design Engineer (Certified EIT License# 56066), with 2 years of experience in subscribing goals and objectives, including geographic and project-type diversity; Understand and... Read more

I am a Senior Electrical Design Engineer (Certified EIT License# 56066), with 2 years of experience in subscribing goals and objectives, including geographic and project-type diversity; Understand and apply National Electrical Code (NEC) & California Electrical Code (CEC) and electrical power engineering principles ¬ Establish system application, design, and operational parameters / sequences. ¬ Ensure QA/QC process. ¬ Determination of project scheduling requirements, manpower requirements, and project budgets. ¬ Conducting field inspections and subsequent detailed inspection reports.

Electrical and Computer Engineer (M.Sc.) with over 15 years of experience in electrical power engineering, industrial automation, and electrical systems design. Proven expertise in delivering projects... Read more

Electrical and Computer Engineer (M.Sc.) with over 15 years of experience in electrical power engineering, industrial automation, and electrical systems design. Proven expertise in delivering projects from concept design through manufacturing, testing, commissioning, and final handover. Experienced in designing LV power distribution systems, control systems, and electrical panels using AutoCAD and EPLAN. Strong practical background in manufacturing and field commissioning provides a unique ability to identify design issues early, optimize engineering solutions, and ensure reliable project execution. Licensed Professional Engineer authorized for both electrical design and construction supervision in the Republic of Serbia. • Electrical Power Systems Design • Low Voltage (LV) Distribution Systems • Industrial Automation • Control System Design • Electrical Distribution & Control Panels • AutoCAD • EPLAN Electric P8 • Single-Line & Multi-Line Schematics • Technical Documentation • Testing & Commissioning • Production Planning • Procurement Coordination • Project Management • Technical Problem Solving