Marijuana leaf for hood ornamentBlind

in CAD Design held by Hoodfins
Contest Ended, Winner(s) have been selected.
Description:
A simple marijuana leaf inside of a circle. This will be for a chrome hood ornament, so it should be "leaf-like" on both sides (3-D) with a ring around it and a one inch wide circular base under the ring where the leaf's base is. No colors necessary.
Wants:
Only 3D design required, no colors. Should be 3 to 3.5 inches tall and wide and about a half inch thick. Bolt location would be under the base of course.
Very important:
Circular Base should be .83 inches in diameter
.262 inches tall
Needs to have a 2mm indentation along the center of the siding that is
exactly .142 inches tall within the .262 inch tall base side.

Bolt location should just be hollow with a one half inch opening.

*** Pictures of these specifications are attached***
Don't Wants:
Nothing too complicated or intricate.
Ask for Sample:
Please send sample of work.
Software:
  1. CAD

Entries

1st Winner
#15 Marijuanitas by unocuatro
Jun 17, 2018 21:08
#1 Marijuana leaf for hood ornament by helghast
Created in Solidworks converted to STL
more
Jun 8, 2018 12:30
#2 Marijuana Leaf by Mecanikad
Hi please check my entry. I hope you like. Please rate it.
more
Jun 8, 2018 20:22
#3 MARIJUANA LEAF by abhi_abhi
Please check my design and rate it :) Its my first contest on CAD CROWD.
more
Jun 8, 2018 23:26
#4 Marijuana leaf for hood ornament 3D Design by Agus Setiawan 892
Under Port Female Thread M.12 x Deep 15mm
more
Jun 9, 2018 5:37
#5 Manjjuana Leaf(SATVA Style Leaf) by Madhan Kumar
I'm really exciting working on this task. I tack this task we consider some details Manjjuana Leaf in three types.
Sativa,Indica and Ruderalis.Now we take Sativa style so why we choose this Because "Sativa leaves are long and slender, often with pronounced serrations, giving the leaves a jagged, almost spiky appearance. The coloration of sativa leaves ranges from bright, lime green to blackish-green at the darkest. The largest leaves can often have up to thirteen leaflets".Please Check and Replay.
more
Jun 10, 2018 6:29
#6 Marijuana leaf for hood ornament Rev2 by helghast
I add 1mm indentation and leaf stem.
more
Jun 11, 2018 0:21
#7 Manjjuana Leaf(SATVA Style Leaf)_1 by Madhan Kumar
Jun 11, 2018 17:01
#9 Amazing Marijuana leaf for hood ornament by Ivan Zerpa
I hope you like my design. For any additional requirement contact me I am at your service.
my best wishes
Ivan Zerpa
more
Jun 13, 2018 1:42
#10 Marijuana Leaf For Hood Ornament by Pkj
Jun 14, 2018 13:09
#11 Hood ornament by Santhosh vishwanatha
Jun 14, 2018 13:59
#13 Marijuana leaf for hood ornament by Mahbub
Sample.
more
Jun 16, 2018 23:16
#14 Hood ornament by Santhosh vishwanatha
Jun 17, 2018 10:18
#16 Marijuna leaf hood by Sricharan
Hope u like it, please suggest if any required...
Regards,
Sricharan
more
Jun 22, 2018 18:19
#17 Marijuna leaf hood by Sricharan
This is a much worked upon improvised display version of the one submitted before. Hope you like it. Please suggest edits and other requirements.
Regards,
Sricharan
more
Jun 24, 2018 7:32
#18 Marijuana leaf for hood ornament by Bijay Kumar
Jun 25, 2018 12:11
#19 Marijuana Leaf by Design Territory
Marijuana Leaf
more
Jun 25, 2018 12:59

Discussion

Design Territory

Designer

Mon, 25 Jun 2018 12:49:48 +0000
In description you say there's a "1 inch wide base". Then again you mention the diameter of base is 0.83in and its 0.262in tall. That's confusing.

Design Territory

Designer

Mon, 25 Jun 2018 11:38:07 +0000
1. "Bolt location should just be hollow with a one half inch opening. " This statement is a bit confusing. The specified diameter is 0.83in so 1.5in bolt opening?
2. Is the thickness of the leaf also 0.5in?
Mon, 25 Jun 2018 10:29:25 +0000
what should be the thickness of circle out side leaf and minimum thickness of leaf?

unocuatro

Designer

Sun, 10 Jun 2018 22:12:16 +0000
Hello Hoodfins, maybe you will attract more designers if you prepay the prize.

Similar Contests on Cad Crowd

GYM EQUIPMENT
I AM LOOKING TO COMBINE THE FUNCTIONALITY OF A TREADMILL AND A STAIR MASTER MACHINE INTO ONE. THIS WOULD MEAN THE STAIRS FROM THE STAIR MASTER WOULD NEED TO BE ABLE TO LAY FLAT WHEN THE USER SELECTS THE OPTION FOR THE TREADMILL. I WOULD LIKE FOR THE STEPS TO BE IN A ESCALATOR FORMAT/CONVEYOR BELT STYLE. THE MACHINE NEEDS TO BE ABLE TO INCLINE USING EITHER HYDRAULICS OR INCLINE MOTOR. THE ARMS OF THE MACHINE SHOULD BE ABLE TO FUNCTION WHEN IN EITHER mode, WHICH MEANS THEY NEEDS TO BE IN ARMS LENGTH. THE BED OF THE MACHINE WHEN IN INCLINE MODE SHOULD ADJUST WITH THE SCREEN SO THAT IS IN EYE REACH OF THE USER.
Bonadikombo Home
Use current hand drawn sketch as a general template. Convert to CAD, adding a foyer at the main entrance/door and toilet (with windows) off of the foyer before Living Room #1. Provide separation of some sort between the foyer and Living Room #1. Relative room sizes should be similar but exact dimensions are not required. Natural lighting of all areas is important. No HVAC systems. To be build in tropical Africa. 2D required, 3D will be nice. Feel free to use colors if needed.
3D CAD Design Of A Dagger
I need a 3D CAD Drawing of a Dagger in a high-res STEP Format. It will be used for 3D Printing and also a graphite mold will be produced on a CNC Milling Machine. The mold will be used for casting silver. Attachment 1: Please follow this sample in regard to detail on the handle and the curves on the blade. Keep the length of the blade on the short side. This is a dagger......not a sword..
CAD Creation For Cylindrical Planter
We're in the process of producing a size range of cylindrical indoor/outdoor planters and need a high-res STEP file to provide to potential manufacturers. This is a high-end homeware product so small details are important. We are open to any small design elements within the specified parameters that keep the product clean and minimal.
HyterLighter Design
Looking to make a unique lighter and need help making a digital 3-D Model so that we can move forward to making our first prototype. Message for more details.