New Dumbbell LineBlind

An alternative to picking up dog dropping with plastic bags. A cheap, easy to build, bio-degradeable design. It should, with a minimum of moving parts, (ideally 1-2 piece cardboard structure), pick up and enclose droppings. Should also include built in handle (reasonably distanced from holding section) Simplicity is key. As will need to be able to produce cheaply in large volumes. MUST BE MASS PRODUCEABLE for cost in the region of $1-2.

We would like a fresh set of eyes on our device ROBERT, a rehabilitation robot that release healthcare workers of heavy and continuous lifting which can cause physical strain and pain in the back, loin, wrists and shoulders. We aim to optimise rehabilitation through more frequently and prolonged exercises which can result in fewer complications and a faster retrieval of a patient’s strength. See more at www.myrobert.com. The current look is a mixture of many components comming together which does not result in a uniform design. Further we whish to incorporate a new robot arm, made by the company KUKA, the LBR iiwa version, https://www.kuka.com/en-de/products/robot-systems/industrial-robots/lbr-iiwa. This will later come in a MEDtech version, similar in use but in white and with a small change to the interface base. CAD data of the industrial version can be used for this design, change is that wiring will come out of the bottom of the medtech version and not the sides like the industrial version, so completely round in base instead of the small square thing on the side of the industrial version (so no visible wires). The industrial version can be downloaded here: https://www.kuka.com/en-de/services/downloads. It is the "LBR iiwa 14 R820" found under division "KUKA Robotics".

FROM SCANNER IMAGES YOU HAVE TO MOUNT COMPLETE SCULPTURE

This consumer product is an accessory that provides enhanced usability to mobile phones and tablets. The latest design of our "Band" is two parts: 1. Round Base that attaches to the back of the phone (made from a low-friction polymer like polyethylene) 2. A "band" that overlaps with the Round Base (1) and rotates/spins around it. (made from polyethylene over-molded with rubber to provide elasticity to the top band part) The rubber part of the band elongates so that an individual's finger can be placed underneath the band and above the base. The elasticity part is important so it can accommodate different finger sizes. The product allows users to hold the phone more securely. Our current challenge is the design of the "Band" (2). This is where we need the help. As shown in the attached STL file for the Band, there are two circles on either side of the flap that holds the finger down. These circle were put there to provide some added elasticity to the rubber piece. While it does functionally work well, the current design does not look durable or very elegant. We'd like to rethink the band design to make it look incredibly user-friendly, allowing the band to stretch upright to accommodate different finger sizes, while being functionally superior to the current design. Designer will need to provide STL files for my prototyping company to be able to work with.

Hi, Im looking for someoone who can design a 3d Product Artwork: Product: 3D Artwork of a round Silicon Glass Coaster Dimensions: Width: 6,5 mm, Diameter: 10,9 cm I have a STL file format, where I started the project, but Im not a professional designer, so I need someone who can maybe start by adopting on my design, as you can find a image attached (IMG1853) and change some things: 1. adopt on the dimensions as written above. 2.add floral structure on the elements/flowers but leaving a straight level at the end. 3. add structure to the buttom and leave here also a straight level at the end. 4.I need a STEP Format at the end. For better understanding I added some pictures of a similar product I would like to orientate on. Also I have a ai Design where you can orientate on the floral structure (see picture attached), but they cant be all taken because the structure is for silicone printin too complex - so the structure needs to be soften up. Please let me know if you can help me with this project. Regards, Jelena.