Industrial Design of a Hand Pulse Detector
in
3D Modeling Design
held by
lesterngbp
Last seen:
2017-08-15 15:08:35
Contest Ended, Winner(s) have been selected.
Description:
We are looking for a industrial design (outlook) of a hand pulse detector. This device will consist of the following.1) Two metal plates on the device that will come in contact with hand when grip on it. This will form a closed circuit between the plates and thereby detect the electrical pulse from the hand (refer to attached for the existing device). Ideally the area of each contact surface of the metal plate should be more than 2000 square mm.
2) A micro USB port for charging the battery.
3) Power Indicator
4) ON/OFF switch.
Internal design of the device is not necessary but must cater enough room to house the below
1) 1500 square mm X 1mm (thickness) PCB
2) 750 square mm X 4mm(thickness) battery.
The design shall be in 3D CAD.
Wants:
- Think out of the box, and open to any type of style. No need to follow the existing design (see attached)- Ergonomics, easy of hold and cater to all sizes of hand.
- Aesthetics pleasing in term of form & color, and originality are to be valued. Visual design is important here. IT MUST BE COOL !! - we want to evoke a visceral reaction to the device
Don't Wants:
- No sharp or clunky edges.- Non-manufacturable designs and complex designs
- Cheap plastic look & feel
Software:
- Any 3D CAD
Additional Information
There will not be a cable connecting to the device, only the USB port for charging. The size of the device need to be portable.Please note that we are looking for something that think out of the box, and open to any type of style. No need to follow the existing design. It can be like a shape of pebbles stone or something ergonomically friendly that can grab around. Important thing is it must look cool - we want to evoke a visceral reaction to the device.
It would be good to have an illustration to show that the size of PCB and Battery can fit into the device.
Entries
#23 Hand Pulse Detector V2
by Pablo Gosso
Hi lesterngbp
Attached Concept 2
Following your specs for look & feel I also use same strategy, Iconic shape, easy to recognize. Minimalistic and good design rules with some small texture details just to add a subtle design flavor, this time the details are in the soft plastic parts, leaving the metal plates clean to appreciate the shapes.
Hope you find it suitable for your product,
Looking forward to your feedback, Pablo
Attached Concept 2
Following your specs for look & feel I also use same strategy, Iconic shape, easy to recognize. Minimalistic and good design rules with some small texture details just to add a subtle design flavor, this time the details are in the soft plastic parts, leaving the metal plates clean to appreciate the shapes.
Hope you find it suitable for your product,
Looking forward to your feedback, Pablo
Jul 13, 2017 21:31
#37 Pulse Detecor 2.0
by ;lzsvpja-] bja]=
Download Files
- Luxion KeyShot — Grip Device 2.1005
- Luxion KeyShot — Grip Device 2.1006
- Luxion KeyShot — Grip Device 2.1007
- Luxion KeyShot — Grip Device 2.1008
- Luxion KeyShot — Grip Device 2.1009
- Luxion KeyShot — Grip Device 2.1010
- Luxion KeyShot — Grip Device 2.1011
- Luxion KeyShot — Grip Device 2.1012
- Luxion KeyShot — Grip Device 2.1013
Jul 14, 2017 14:39
Discussion
Showing last 20 comments - View All
Congrats to Winner& Cadcrowd
Apologies, no more new submission will be considered.
Those with Nominate or with 4 stars are qualify for the final round selection and you are welcome to refine your design with more details like the manufacturing consideration or material selection.
Those with Nominate or with 4 stars are qualify for the final round selection and you are welcome to refine your design with more details like the manufacturing consideration or material selection.
How do we know the shortlisted candidates.Will the client PM them?
Thanks for all your submission and appreciate your time and effort put in.
As of now, I have shorted listed for the winner. No new submission will be considered as the contest is closed. The reason for the extension is to let the short listed designer to have the time to refine their design as this content start till now is very short, only weeks till now.
Let me know if you have any question or concern. Thanks
As of now, I have shorted listed for the winner. No new submission will be considered as the contest is closed. The reason for the extension is to let the short listed designer to have the time to refine their design as this content start till now is very short, only weeks till now.
Let me know if you have any question or concern. Thanks



I agree with Adriano 135 entries surely one of them is good enough to be selected. Cadcrowd should be charging money for an extended contest..after all, time is money.
I do not think it's right to postpone the challenge again.
Everyone here has put a lot of effort into their designs, based on a predetermined deadline.
If a desired product did not appear yet, you should give better feedback as to what you are really looking forward to seeing.
I bet everyone here agrees with what I'm talking about.
Everyone here has put a lot of effort into their designs, based on a predetermined deadline.
If a desired product did not appear yet, you should give better feedback as to what you are really looking forward to seeing.
I bet everyone here agrees with what I'm talking about.
Looking forward to your feedback to develop the concept
Hi
Please rate my last design so i can improve
Please rate my last design so i can improve
Nice Cristiano, really unique design.



Hi Adam,
The thickness of battery and PCB is petty much fixed as stated. The area is given as a guide for you to cater enough room for the component, so it can be any size as long as it is within the area (sq. mm) specified.
The thickness of battery and PCB is petty much fixed as stated. The area is given as a guide for you to cater enough room for the component, so it can be any size as long as it is within the area (sq. mm) specified.
Would it be possible to get the width, height, and depth of the battery and the width and height of the PCB, or can it be any size as long as it is within the sq. mm's specified ?


Ergonomics is a concern when griping due to the profile. Aesthetics need to improve.



Similar Contests on Cad Crowd
Racing drone (quadcopter) from notes to CAD and 3D model
Your task is to draft a mini racing drone from my design specifications.
The drone itself will consist of two pieces of moulded carbon fibre:
- bottom hull
- hood
Key features of the drone:
- two piece construction with interlocking lip
- tube arms (16mm outer diameter, 12mm inner diameter)
- fit 6" diameter propeller (152.4mm)
- 16x19mm standard motor mounting
- fit standard HS1177 camera with adjustable camera angle from 0° - 70° of tilt
- fit standard flight controller circuit board (30.5mm square mounting holes on the bottom)
- 4mm thick at motor mount
- 3-4mm thickness of hull
THE ATTACHED ZIP FILE CONTAINS SKETCHUP FILES WITH DIMENSIONAL DATA, PROTOTYPE IMAGES AND IMAGES TO USE AS A REFERENCE
Deliverables:
- Technical CAD model of drone components
- Inverse CAD model for the moulds for both pieces
- 3D renders
Bonus points for:
- finite element analysis to highlight structural weaknesses and suggest improvements
- include motors, propeller and other electronics in the 3D renders
Keyshot Product Rendering
Render photo-realistic multiple view of products for use in visualization, web/print etc.
8 product models, 3D STP files already available
Requiring only application of surface finish and lighting options.
Faith Based Jewelry_1_Christianity
We are a start up launching a line of jewelry based on faith/religion. We are looking to launch with a number of necklaces and bracelets so we are looking for highly innovative designs for pendants and bracelet charms which signify faith based meaning.
We want our jewelry line to be worn everyday (not just on occasions) as a charm so that one is never without the blessings of one's faith. We want it to be an essential companion to a user, through thick and thin, to give them the reassurance that one is never alone.
We expect:
2 designs for necklace pendants
2 designs for the bracelet charms
The designs should be made for metal (sterling silver).
ecig design
we need a ecig design, now all ecigs design are boring, all MOD looks the same, ego style all looks the same.we need a unique one,
Floral Glass Coaster 3D Artwork - STEP
Hi,
Im looking for someoone who can design a 3d Product Artwork:
Product: 3D Artwork of a round Silicon Glass Coaster
Dimensions: Width: 6,5 mm, Diameter: 10,9 cm
I have a STL file format, where I started the project, but Im not a professional designer, so I need someone who can maybe start by adopting on my design, as you can find a image attached (IMG1853) and change some things:
1. adopt on the dimensions as written above.
2.add floral structure on the elements/flowers but leaving a straight level at the end.
3. add structure to the buttom and leave here also a straight level at the end.
4.I need a STEP Format at the end.
For better understanding I added some pictures of a similar product I would like to orientate on.
Also I have a ai Design where you can orientate on the floral structure (see picture attached), but they cant be all taken because the structure is for silicone printin too complex - so the structure needs to be soften up.
Please let me know if you can help me with this project.
Regards,
Jelena.
REDA
Designer