Cat Bong Design

We are a start-up design company based in Mullingar and supported by Enterprise Ireland as a HPSU. We require an experienced solidworks engineer to complete various sheet metal components in flat sheet and folded. Initially we would require in the region of 20/30 hours service which may be extended.

The project is to develop a small waterproof weather monitoring button which will include a UV, humidity and temperature sensors. The button will be pairing with a mobile phone for transmitting data. This button could be used both at the beach to monitor UV exposure but also in house for room climate monitoring, We need a small electronic and sensor enclosure with the following specs: 1) Button or other (rectangular/cube/etc) similar shape 2) Small dimensions to host a 15mm x 25mm x 3mm PCB 3) Include a coin battery with an option of easy access for replacement 4) The enclosure/product should have a small protected whole for a humidity/temperature sensor (not more than 2mm diameter) 5) Include a UV sensor so access to light is needed 6) Include a Power switch/button 7) Include a led for indicating operation 8) Include a robust belt clip (or other removable clip, or/plus a magnet) built into the design 9) Waterproof design 10) A trendy design aesthetically pleasing as possible 11) we need the source solidworks files for printing on our 3D printing We intent to further work with the winning designer so as to fine-tune the design after initial testings

A travel baby wipes case with two snap clip mechanisms. One to open the case to reload the wipes and another on top to access the wipes. The design should be as flat, sleek and as close to dimensions as possible. Various prints will be added so design should consider how a print may be interrupted or warped. A small loop needs to be added where desired for a lanyard to attach the case to bags strollers etc. Dimensions should be as close to W:120mm H:21mm D:30mm. The design should not infringe on internal compartment for wipes so the case can be closed easily. Potential for future projects for winner.

Concept: Create a device with the ability for a dog to put his paw on six different areas. Embedded in the pad or mat are proximity switches. As the dog places their paw in each area both words, i.e. Drink, Eat, Outside, Love Me, Play and Leave Me Alone are played along with an accompanied dog sound, background noise (or Bark, etc). They include: 1. Drink 2. Eat 3. Outside 4. Love 5. Play 6. Leave me alone I would also link up via marketing with the current paw treat dispenser (marketing relationship), some have dual cameras so u can see them and they can see u and u can electronically send them a treat. https://www.bedbathandbeyond.com/store/product/petcube-bites-interactive-wi-fi-pet-camera-and-treat-dispenser/3342848?skuId=62817813&enginename=google&mcid=PS_googlepla_nonbrand_pet_online&product_id=62817813&adtype=pla&product_channel=online&adpos=&creative=223560994791&device=m&matchtype=&network=g&mrkgadid=3245052790&mrkgcl=609&rkg_id=0&utm_campaignid=71700000037121734&utm_adgroupid=58700004139975561&targetid=92700034063773421&gclid=EAIaIQobChMIiYPHiaGt6AIVCmKGCh2ClQB_EAQYAyABEgK17PD_BwE&gclsrc=aw.ds Imagine a hybrid of a puppy dispensing system above with the Einstein Training Pad. The dog steps on hungry or water His bowls fill up Gets a Treat How many dogs are there in the US? According to a pet owners survey, there were approximately 89.7 million dogs owned in the United States in 2017. This is an increase of over 20 million since the beginning of the survey period in 2000, when around 68 million dogs were owned in the United States. Number of dogs in the U.S. 2000-2017. Published by Emma Bedford, Nov 27, 2019. The statistic also shows the share of pet owners in the United States in 2016, by generation. In 2016, 35 percent of pet owners were Millennials. Baby boomers were the next largest generation of pet owner, with 32 percent. Statista 2020

We are seeking designs for a pet wearable band. Which will encase an oval shaped device that will go on a pet collar. At this time we are seeking some creative designs but not the actual 3D printed versions. We have attached a few photos of what we are seeking; including a version that would be a bow for a female and bone for a male. We are open to other concepts and ideas. The oval in the middle of the designs will house the wearable.