Description:We are seeking designs for a pet wearable band. Which will encase an oval shaped device that will go on a pet collar. At this time we are seeking some creative designs but not the actual 3D printed versions. We have attached a few photos of what we are seeking; including a version that would be a bow for a female and bone for a male. We are open to other concepts and ideas. The oval in the middle of the designs will house the wearable.
Wants:We would like to see a variety of different bands and other cool designs.
Don't Wants:Just to see bows and bones. I need everyone to be as creative as possible.
- Any (1.0)
#20 Pet Wearable by Rhizky Ariyansyah
#21 pet wearable- Please check the attached files. by Abid Yusuf
#23 Pet Wearable_phv_02 by Pop Horea
#31 BOW AND BONE by SHIVAM MISHRA
Similar Contests on Cad Crowd
Baby wipes case
A travel baby wipes case with two snap clip mechanisms. One to open the case to reload the wipes and another on top to access the wipes. The design should be as flat, sleek and as close to dimensions as possible. Various prints will be added so design should consider how a print may be interrupted or warped. A small loop needs to be added where desired for a lanyard to attach the case to bags strollers etc. Dimensions should be as close to W:120mm H:21mm D:30mm. The design should not infringe on internal compartment for wipes so the case can be closed easily. Potential for future projects for winner.
Interchangeable Battery Adapter Holster Pack - Industrial CAD Designer
Hello, I need someone to help me make a interchangeable battery clip adapter where these Ryobi batteries (found from Home depot) clip into each other as seen in picture It must be able to maintain enough room and functionality where the electrical terminals make proper contact. The batteries in the picture are laid out exactly how I want it to clip into each other. Just fill in the space between the battery with the housing that I need for you to design. I also need an access port about 7mm in diameter. The designer must already have access to these batteries which are common from home depot.
to design a container shelving system.
Small waterproof weather sensor housing
The project is to develop a small waterproof weather monitoring button which will include a UV, humidity and temperature sensors. The button will be pairing with a mobile phone for transmitting data. This button could be used both at the beach to monitor UV exposure but also in house for room climate monitoring, We need a small electronic and sensor enclosure with the following specs: 1) Button or other (rectangular/cube/etc) similar shape 2) Small dimensions to host a 15mm x 25mm x 3mm PCB 3) Include a coin battery with an option of easy access for replacement 4) The enclosure/product should have a small protected whole for a humidity/temperature sensor (not more than 2mm diameter) 5) Include a UV sensor so access to light is needed 6) Include a Power switch/button 7) Include a led for indicating operation 8) Include a robust belt clip (or other removable clip, or/plus a magnet) built into the design 9) Waterproof design 10) A trendy design aesthetically pleasing as possible 11) we need the source solidworks files for printing on our 3D printing We intent to further work with the winning designer so as to fine-tune the design after initial testings
New product line for site furnishings manufacturer
We have recently purchased an older site furnishing manufacturer and would like to introduce a new and more modern product line. http://street.woodcraftdesignltd.com/ Please feel free to visit the current website to see our existing products. We primarily want a Park Bench Waste and recycling receptacle A lighted bollard Later on adding a Poster Pillar and a Bike rack Our chosen new line will be put into production and therefore will need to be Modern,lightweight but durable,as maintenance free as possible and not too complicated to manufacture and assemble. In our existing product we use the following materials Steel and Aluminum for structure Cedar, Ipe and Oak for seating Our most popular bench size is 1800mm We would like to incorporate composite materials for a seating option (bearing in mind we have had issues with composite sagging in heat We would like to compete with companies such as Maglin and Wishbone Our existing products do not have any CAD drawings included and this makes it more difficult for us to be specified in by landscape architects. We are not sure exactly what they require and any guidance in that would be appreciated.