Sheet metal fabrication design

in Product Design held by Ben Barrett
Contest Closed
Description:
We are a start-up design company based in Mullingar and supported by Enterprise Ireland as a HPSU.

We require an experienced solidworks engineer to complete various sheet metal components in flat sheet
and folded.

Initially we would require in the region of 20/30 hours service which may be extended.
Wants:
All details will be discussed evaluation of applicants CV and phone conversation.
Don't Wants:
Person who is unable to meet face to face initially and perhaps for a few follow-up meetings. Therefore someone relatively local.
Software:
  1. SolidWorks

Entries

No Entries Submitted Yet.

Discussion

No Comments Submitted Yet.

Similar Contests on Cad Crowd

Cat Bong Design
I have Various Shapes That I seek to Have Produced ,for Enthusiast, my First Project will be my Favorite Subject. CATS. I'm a cat mom and would like to eventually have this Produced.The Best Cat BONG Design.
Small waterproof weather sensor housing
The project is to develop a small waterproof weather monitoring button which will include a UV, humidity and temperature sensors. The button will be pairing with a mobile phone for transmitting data. This button could be used both at the beach to monitor UV exposure but also in house for room climate monitoring, We need a small electronic and sensor enclosure with the following specs: 1) Button or other (rectangular/cube/etc) similar shape 2) Small dimensions to host a 15mm x 25mm x 3mm PCB 3) Include a coin battery with an option of easy access for replacement 4) The enclosure/product should have a small protected whole for a humidity/temperature sensor (not more than 2mm diameter) 5) Include a UV sensor so access to light is needed 6) Include a Power switch/button 7) Include a led for indicating operation 8) Include a robust belt clip (or other removable clip, or/plus a magnet) built into the design 9) Waterproof design 10) A trendy design aesthetically pleasing as possible 11) we need the source solidworks files for printing on our 3D printing We intent to further work with the winning designer so as to fine-tune the design after initial testings
Calling all pet product designers for a new innovative dog feeding board.
I have read your description carefully and Finally, I make design as per your requirement.
New product line for site furnishings manufacturer
We have recently purchased an older site furnishing manufacturer and would like to introduce a new and more modern product line. http://street.woodcraftdesignltd.com/ Please feel free to visit the current website to see our existing products. We primarily want a Park Bench Waste and recycling receptacle A lighted bollard Later on adding a Poster Pillar and a Bike rack Our chosen new line will be put into production and therefore will need to be Modern,lightweight but durable,as maintenance free as possible and not too complicated to manufacture and assemble. In our existing product we use the following materials Steel and Aluminum for structure Cedar, Ipe and Oak for seating Our most popular bench size is 1800mm We would like to incorporate composite materials for a seating option (bearing in mind we have had issues with composite sagging in heat We would like to compete with companies such as Maglin and Wishbone Our existing products do not have any CAD drawings included and this makes it more difficult for us to be specified in by landscape architects. We are not sure exactly what they require and any guidance in that would be appreciated.
New kettlebell weight range
New kettlebell design. I would like 3d CAD drawings with details measurements to use for producing moulds for a new kettlebell range in cast iron. from range of 5KG to 24KG.(5,8,12,16,20,24kg). Front and rear with a flat surface, one side showing weight in both KG/LBS, the otherside left blank for logo. Handlewidth diameter (35mm) and dimensions between horns of handle and handle to ball distance for all kettlebells shoud be the same. At the base of the kettlebell, a circular handle built into the design should be larger than the kettlebell base, with 28mm grip diameter, and the first few cm of the base hollowed out to allow a hand and fingers to reach inside and grip almost all the way around the bar throughout the full circle.