Faith Based Jewelry_1_Christianity Blind

This consumer product is an accessory that provides enhanced usability to mobile phones and tablets. The latest design of our "Band" is two parts: 1. Round Base that attaches to the back of the phone (made from a low-friction polymer like polyethylene) 2. A "band" that overlaps with the Round Base (1) and rotates/spins around it. (made from polyethylene over-molded with rubber to provide elasticity to the top band part) The rubber part of the band elongates so that an individual's finger can be placed underneath the band and above the base. The elasticity part is important so it can accommodate different finger sizes. The product allows users to hold the phone more securely. Our current challenge is the design of the "Band" (2). This is where we need the help. As shown in the attached STL file for the Band, there are two circles on either side of the flap that holds the finger down. These circle were put there to provide some added elasticity to the rubber piece. While it does functionally work well, the current design does not look durable or very elegant. We'd like to rethink the band design to make it look incredibly user-friendly, allowing the band to stretch upright to accommodate different finger sizes, while being functionally superior to the current design. Designer will need to provide STL files for my prototyping company to be able to work with.

An alternative to picking up dog dropping with plastic bags. A cheap, easy to build, bio-degradeable design. It should, with a minimum of moving parts, (ideally 1-2 piece cardboard structure), pick up and enclose droppings. Should also include built in handle (reasonably distanced from holding section) Simplicity is key. As will need to be able to produce cheaply in large volumes. MUST BE MASS PRODUCEABLE for cost in the region of $1-2.

Hi all, thanks for checking out my contest! I am involved with a company that is looking to receive some entries for a "prototype" electric unicycle. If you aren't familiar let me give you a brief background. Remember the hoverboards last xmas?? The electric unicycle works on essentially the same principle (upside down pendulum theory) to achieve self balancing capability. The current offerings on the market just don't cut it, the plastics are basically thrown together around the requirements of a build, rather than incorporating the necessary components into the design for a smooth finish. I would like the final product to be somewhat futuristic/prototypish looking, maybe a bit sporty. You can get a feeling for whats out there by doing a google search for "electric unicycle". Integral to the design there are 3 requirements. 1.) Obviously the plastic fairing will need to have a cavity for the wheel, but in addition, it will need to subtly include a space for lipo batteries, (doesnt have to be in any particular shape however), and also must include spot for a pcb control board. Both of these items arent excessively large, the PCB is about 4X3 inches and the batteries are about 5X5X1 (but can be reconfigured). 2.) I would also like to incorporate into my design a headlight, and a tail light if possible, but most concerned with head light. Would also like to leave the option open to include small bluetooth speakers, however these would not take very much space at all. 3.) Finally, this design will need to have a retractable handle for balance when getting on/off.

We are looking for a industrial design (outlook) of a hand pulse detector. This device will consist of the following. 1) Two metal plates on the device that will come in contact with hand when grip on it. This will form a closed circuit between the plates and thereby detect the electrical pulse from the hand (refer to attached for the existing device). Ideally the area of each contact surface of the metal plate should be more than 2000 square mm. 2) A micro USB port for charging the battery. 3) Power Indicator 4) ON/OFF switch. Internal design of the device is not necessary but must cater enough room to house the below 1) 1500 square mm X 1mm (thickness) PCB 2) 750 square mm X 4mm(thickness) battery. The design shall be in 3D CAD.

Hi, Im looking for someoone who can design a 3d Product Artwork: Product: 3D Artwork of a round Silicon Glass Coaster Dimensions: Width: 6,5 mm, Diameter: 10,9 cm I have a STL file format, where I started the project, but Im not a professional designer, so I need someone who can maybe start by adopting on my design, as you can find a image attached (IMG1853) and change some things: 1. adopt on the dimensions as written above. 2.add floral structure on the elements/flowers but leaving a straight level at the end. 3. add structure to the buttom and leave here also a straight level at the end. 4.I need a STEP Format at the end. For better understanding I added some pictures of a similar product I would like to orientate on. Also I have a ai Design where you can orientate on the floral structure (see picture attached), but they cant be all taken because the structure is for silicone printin too complex - so the structure needs to be soften up. Please let me know if you can help me with this project. Regards, Jelena.