Im looking for someoone who can design a 3d Product Artwork:
Product: 3D Artwork of a round Silicon Glass Coaster
Dimensions: Width: 6,5 mm, Diameter: 10,9 cm
I have a STL file format, where I started the project, but Im not a professional designer, so I need someone who can maybe start by adopting on my design, as you can find a image attached (IMG1853) and change some things:
1. adopt on the dimensions as written above.
2.add floral structure on the elements/flowers but leaving a straight level at the end.
3. add structure to the buttom and leave here also a straight level at the end.
4.I need a STEP Format at the end.
For better understanding I added some pictures of a similar product I would like to orientate on.
Also I have a ai Design where you can orientate on the floral structure (see picture attached), but they cant be all taken because the structure is for silicone printin too complex - so the structure needs to be soften up.
Please let me know if you can help me with this project.
Additional InformationThe designer needs to create a layout using individual floral elements from the eps file attached and the design is going to be CNC machined into a mould and needs to be between 0 and 3 mm height.
Similar Contests on Cad Crowd
iPhone/Android Accessory Design Enhancement
This consumer product is an accessory that provides enhanced usability to mobile phones and tablets. The latest design of our "Band" is two parts: 1. Round Base that attaches to the back of the phone (made from a low-friction polymer like polyethylene) 2. A "band" that overlaps with the Round Base (1) and rotates/spins around it. (made from polyethylene over-molded with rubber to provide elasticity to the top band part) The rubber part of the band elongates so that an individual's finger can be placed underneath the band and above the base. The elasticity part is important so it can accommodate different finger sizes. The product allows users to hold the phone more securely. Our current challenge is the design of the "Band" (2). This is where we need the help. As shown in the attached STL file for the Band, there are two circles on either side of the flap that holds the finger down. These circle were put there to provide some added elasticity to the rubber piece. While it does functionally work well, the current design does not look durable or very elegant. We'd like to rethink the band design to make it look incredibly user-friendly, allowing the band to stretch upright to accommodate different finger sizes, while being functionally superior to the current design. Designer will need to provide STL files for my prototyping company to be able to work with.
The ROBERT project
We would like a fresh set of eyes on our device ROBERT, a rehabilitation robot that release healthcare workers of heavy and continuous lifting which can cause physical strain and pain in the back, loin, wrists and shoulders. We aim to optimise rehabilitation through more frequently and prolonged exercises which can result in fewer complications and a faster retrieval of a patient’s strength. See more at www.myrobert.com. The current look is a mixture of many components comming together which does not result in a uniform design. Further we whish to incorporate a new robot arm, made by the company KUKA, the LBR iiwa version, https://www.kuka.com/en-de/products/robot-systems/industrial-robots/lbr-iiwa. This will later come in a MEDtech version, similar in use but in white and with a small change to the interface base. CAD data of the industrial version can be used for this design, change is that wiring will come out of the bottom of the medtech version and not the sides like the industrial version, so completely round in base instead of the small square thing on the side of the industrial version (so no visible wires). The industrial version can be downloaded here: https://www.kuka.com/en-de/services/downloads. It is the "LBR iiwa 14 R820" found under division "KUKA Robotics".
I am building a new home and require innovative interior architectural design options ( kitchen, family room, living room and powder room) that will accommodate an exterior elevation that is already defined. One of the most important aspects to this assignment is the location of the interior foyer relative to the location of stairs that go up to the 2nd floor and down to the basement. The desired design of the foyer is to be defined in terms of its presence but not in a manner that it takes away from the interior space in a significant manner. Once a 1st floor layout is approved, the need to prepare a modern and eye catching interior design (with furniture, crown holding, tray ceilings, wainscotting, etc. ) with photo like renderings will be required. I have attached the exterior elevation (which is reversed to the actual location of the garage) but it provides a sense of the foyer location. I have also provided a PDF of the ground floor footprint that we have to work with. The dimensions of the foot print is fixed. This ground floor plan design is not the optimal in terms of the foyer so we are looking for innovative designs that will fit within the plan dimensions and our needs..
Racing drone (quadcopter) from notes to CAD and 3D model
Your task is to draft a mini racing drone from my design specifications. The drone itself will consist of two pieces of moulded carbon fibre: - bottom hull - hood Key features of the drone: - two piece construction with interlocking lip - tube arms (16mm outer diameter, 12mm inner diameter) - fit 6" diameter propeller (152.4mm) - 16x19mm standard motor mounting - fit standard HS1177 camera with adjustable camera angle from 0° - 70° of tilt - fit standard flight controller circuit board (30.5mm square mounting holes on the bottom) - 4mm thick at motor mount - 3-4mm thickness of hull THE ATTACHED ZIP FILE CONTAINS SKETCHUP FILES WITH DIMENSIONAL DATA, PROTOTYPE IMAGES AND IMAGES TO USE AS A REFERENCE Deliverables: - Technical CAD model of drone components - Inverse CAD model for the moulds for both pieces - 3D renders Bonus points for: - finite element analysis to highlight structural weaknesses and suggest improvements - include motors, propeller and other electronics in the 3D renders
Faith Based Jewelry_1_Christianity
We are a start up launching a line of jewelry based on faith/religion. We are looking to launch with a number of necklaces and bracelets so we are looking for highly innovative designs for pendants and bracelet charms which signify faith based meaning. We want our jewelry line to be worn everyday (not just on occasions) as a charm so that one is never without the blessings of one's faith. We want it to be an essential companion to a user, through thick and thin, to give them the reassurance that one is never alone. We expect: 2 designs for necklace pendants 2 designs for the bracelet charms The designs should be made for metal (sterling silver).