Original Sketches to DWG Re-Draft / Conversion (2 weeks)

in CAD Design held by Jim Cristow
Contest Closed
Description:
Required is to convert original architectural sketches into layered DWG drawings. The unit of interest is the first unit from right to left and the work can be limited to re-drafting of plans and details only for this unit. Details from mid units must be used to overlay details for the unit of interest (as the original drafter provided greater details that apply for for all units only on the 2nd, 3rd of 4th units)
Wants:
Quality of re-drafting.
Time-to-delivery (2 weeks)
Software:
  1. AutoCAD (2017)
Additional Information
This project has been amended. Two additional files show rough sketches for ideas for updates to original ground and basement floor plans to accommodate a restaurant equipped with flyer, griddle, gas oven and a pizza oven. Using these sketches required is to also overlay these updates over the original plans and create mechanical drawings to support these new floor plans. Changes to layout of restaurant are allowed if one considers necessary or has ideas for a better layout.

Entries

#8 SHEET 2 by tigre
May 12, 2017 9:24
#7 All Drawings by Smart Engineering Solutions
Hi...All drawings are ready. JPEG attached.
Thanks
SES
more
May 11, 2017 13:55
#6 plan by Mr.X khan
Plan
more
May 11, 2017 10:23
#4 Auto Cad Drawing No 3 by Smart Engineering Solutions
Hi,
Please see attached screen shot of drawing #3. Hope you would like it and consider it for your requirement. Please let us know for the further formalities.
Thanks
SES
more
May 4, 2017 15:42
#3 Original Sketches to DWG Re-Draft / Conversion by Percie
Hi Jim,
I attach 3 plan to one drawings so you can download it one time. Hope you Like the Screenshot.
The Elevation and other last 2 sheet will be follow after the payment change to Prepaid.
Regards,
more
May 2, 2017 6:58
#2 DWG Re-Draft Conversion (Sheet4 & 5) by helghast
May 1, 2017 21:47
#1 DWG Re-Draft / Conversion (Sheet 1 to 3) by helghast
Only sheet 1 to 3. Im not yet finish on sheet 4 and 5.
more
May 1, 2017 8:46

Discussion

Jim Cristow

Buyer

Wed, 17 May 2017 11:20:32 +0000
Hi - thanks to everyone for the submissions. I have selected helghast as a partial winner (based on the fact that the amendments noted in the Additional Information section were not fully addressed). He has now collected his prize through an amended private contest. Congratulations to helghast and many thanks to everyone!

Mr.X khan

Designer

Wed, 17 May 2017 06:15:21 +0000
Kindly Announce the winner. Thanks.

Jim Cristow

Buyer

Thu, 04 May 2017 12:57:15 +0000
Thanks for the comments, Adam. What are the guarantees that all requirements will be completed if one prepays?
Thu, 04 May 2017 02:50:09 +0000
It's amazing how many people will spend the time for a no gurantee, payment pending contest.
Sat, 29 Apr 2017 22:59:21 +0000
Hello will you accept a drawings on 2016 format? Thanks
Sat, 29 Apr 2017 11:09:52 +0000
I like this project work. I work on it
Sat, 29 Apr 2017 02:13:10 +0000
Hello,

With payment pending, it's a substantial time risk for a designer to work on this "contest".
It probably shouldn't be a contest at all since the deliverable is straightforward.

Just my take on it.
Sat, 29 Apr 2017 01:52:46 +0000
I might give it a shot. T-Dot eh? How old are these plans? I could do them in ft-in with secondary units being mm. I am also thinking one DWG for PDF underlays, one to XREF those into floor plans, and a third to XREF the plans into a parent file for the sections and elevations and the project layout sheets. Your thoughts?
I am surprised that Toronto allowed windowless second bedrooms in the inside units, but you're only interested in the end unit at plan east, correct?
Fri, 28 Apr 2017 17:53:22 +0000
kindly change payment status

thnx

Jim Cristow

Buyer

Fri, 28 Apr 2017 17:51:03 +0000
Hi, thank you for your comment. The original project will be amended shortly to request for mechanical drawings for a restaurant on the first level along with work area and bathrooms in the basement.
Fri, 28 Apr 2017 17:42:04 +0000
Hello Sir, Thanks for post the job, i am working on it.

Similar Contests on Cad Crowd

Taylor Sunroom- floor plans, deck plan, roof plan & elevations
1. To scale metric Site Plan (showing new layout of sunroom and decks) (revise from existing plan not to scale) Foundation plan, floor plans, deck plan, roof plan, elevations (3), Section & section details (revise from existing drawings) New drawings for an upper deck (measurements provided) with side spiral stairs
Interchangeable frisbee disc design
Hello, Looking for a qualified individual to draft a CAD design for a disc golf disc aka frisbee disc that has a standard center core that can be screwed into exchangeable outer rims. The design must be within specs that I have outlined and feature an air tight interlocking design that will not come loose when the disc is thrown or hits an object. Production of this item would be injection molded with TPE.
ART CAM tool paths for cnc
I need my own pen and ink drawings converted from JP2 to g code for a CNC milling project.
Hard-Hat Clipable Safety Notification System (#2)
We were very happy with the results from our first design concept competition so we decided to host another Cad Crowd competition but focus more on designing to a specific PCB and shape this time. We're looking for small, sleek, manufacurable, and aesthetic designs for a hard-hat clipable safety notification system for construction workers to improve their work safety. The device can sense dangers with internal electronics and alert the user real-time using light and sound notifications. The device will be clipped to the under-side of the hard-hat (see attached image "placement.png"). The device has LEDs along the curved portion of the PCB and two side-fire speakers to convey dangers to the user (see attached image "PCB.png"). There is a snap-dome push button on the right side of the PCB. Please design a fused rubber actuator for the snap-dome. Assembly: The front case will have 3mm screw bosses. The clip slides over the boss, next the PCB, then the back case, then a screw to hold it all together (see attached image "assembly.png") . The project will be pre-payed once there is 3 quality design entries (including CAD files).
4 Transmission Drawings for Patent Application
-1 Overall Control System Diagram -1 Overall Layout of the Servo-Automated Gearbox -2 Cross Sectional Drawings of Key Components NOTE: All drawings will have numbers and lettering. 2 drawings will have some hatching.