Taylor Sunroom- floor plans, deck plan, roof plan & elevations

in CAD Design held by Taylor Sunroom
Contest Closed
Description:
1. To scale metric Site Plan (showing new layout of sunroom and decks) (revise from existing plan not to scale)

Foundation plan, floor plans, deck plan, roof plan, elevations (3), Section & section details (revise from existing drawings)

New drawings for an upper deck (measurements provided) with side spiral stairs
Wants:
basic drawings for Red Deer Alberta Development Permit, and Building Permit
Don't Wants:
overly complicated to time consuming drawings - I have the basic drawings which are revised - just not a program to have them drawn with auto cad.
Software:
  1. AutoCAD

Entries

#10 house2 by viz_rado
Jan 16, 2014 8:55
#9 house2 by viz_rado
Jan 16, 2014 8:55
#8 house by viz_rado
Jan 16, 2014 8:54
#7 Glass and steel house by viz_rado
Jan 16, 2014 8:53
#6 Glass and steel house by viz_rado
Jan 16, 2014 8:52
#5 Glass and steel house by viz_rado
Jan 16, 2014 8:51
#3 deck sample by re:designusa
multi tiered deck with landscaping
more
Jan 12, 2014 17:50
#2 SAMPLE OF WORK by DBARN
Download Files
THIS IS A SAMPLE OF ARCHITECTURAL DRAFTING WORK THAT I DO.
more
Jan 8, 2014 19:34
#1 Sample project by DamarHut
Sample project
more
Dec 18, 2013 3:46

Discussion

Thu, 02 Jan 2014 08:44:11 +0000
Hi Taylor!!
Please include attachments.
I am happy to do this work for you.

Thanks
Khyati
Wed, 18 Dec 2013 07:13:07 +0000
Hi Taylor,
Please include attachments of your requirements, pdf or hand drawn etc.
Looking forward for your response soon.

Thanks
Izan
Wed, 18 Dec 2013 03:40:29 +0000
Hi Taylor,
I am a Civil Engineer / AutoCAD drafter from Australia. Looking forward to doing this work for you once drawings are uploaded.
Kind Regards,
Stephanie

MacKenzie Brown

Administrator

Mon, 16 Dec 2013 20:06:23 +0000
Hi Taylor,
Please remember to include attachments so the freelancers will fully understand your project. If you need help including these, please send us an email or refer to this link: http://goo.gl/mnFSgg
Thanks,
MacKenzie

Similar Contests on Cad Crowd

Original Sketches to DWG Re-Draft / Conversion (2 weeks)
Required is to convert original architectural sketches into layered DWG drawings. The unit of interest is the first unit from right to left and the work can be limited to re-drafting of plans and details only for this unit. Details from mid units must be used to overlay details for the unit of interest (as the original drafter provided greater details that apply for for all units only on the 2nd, 3rd of 4th units)
Myth and Mystique
I am trying to make a silicone mermaid brush. I need a cad design of the tail since the ferrule and hair would be added on. This is a make up brush used for make up. I would like the tail to have scales as well as a bit of pearls.
Nut Case Puzzle
The product is a hollow bolt that can be unlocked and twisted apart. It’s modelled after the “nut case” puzzle, but should be much higher quality. There should be two nuts threaded to twist up and down the shaft. When the nuts get to the head of each bolt, they should turn freely counter-clockwise to match a number on top of each bolt head. In addition to the primary threads that allow the the nuts to twist up and down the bolt shaft there should be a lip with an opening that lines up with dog clips (or protrusions) at the end of each bolt opposite its head. This opening is matched by lining up a number on the nuts with the appropriate number on the head of the bolt. Once the numbers are matched, the bolts can be pulled apart and the nuts screwed back towards the center of the shafts, pushing the dog clips and separating the bolts. When the nuts meet in the center, the user should be able to rotate the heads of each bolt counter-clockwise to release the nuts and take the puzzle completely apart, or thread the nuts back up the shaft to return the puzzle to one piece.
Electronic toothbrush Floss head
I have designed a reusable floss-head attachment for a sonic toothbrush. The purpose of this design is to send to a machinist in order to create a plastic injection mold. The issue I have is that I am not an experienced 3D modeler. I used sketchup to create the design and then used free cad to convert the STL file into a STEP CAD file. Each machinist I have sen the STL and CAD files to has not been able to work either of these files.