Garbage Disposal

in 3D Modeling Design held by Dipesh
Contest Closed
Description:
Need to design under the sink garbage disposal unit. There are lot of garbage disposals made with a purpose of kitchen waste disposal. The envelope size will be around 6 inches in diameter and about 8-10 inches long. The unit will utilize 1/3 or 1/2 HP motor.
Wants:
Part designs, Assembly and components 3D models and manufacturing drawings,
Software:
  1. Siemens NX (Unigraphics)
  2. PTC Creo Parametric / Pro-E

Entries

#5 Garbage Disposal Device by Mahbub
May 12, 2016 10:12
#4 garbage disposal by Anekant Jain
Here i have attached every possible view of design. Dimensions can be adjusted according to the requirements and motor and blade size. thank you
more
May 3, 2016 12:46
#3 garbage disposal by Anekant Jain
The design consist all the parts which are required. i can provide you the detail drawing of the design.. thank you.
more
May 2, 2016 12:47
#2 Garburator Concept Design by Decker
I have modelled a concept layout for a garburator today. It is missing a motor, which would be I think a purchased OEM part along with the mounting hardware for the sink. Note I can design or find these parts too just need more time. Attached is a rendering along with a quick assembly drawing showing basic dimensions. This one is actually drawn today by me.
more
Apr 15, 2016 20:26
#1 InSinkErator Evolution Excel Garbage Disposal by Decker
InSinkErator Evolution Excel Garbage Disposal . I can provide, mechanical design, modeling and drafting for this type of equipment. Or I can just help spec one for you.
more
Apr 14, 2016 1:47

Discussion

Tue, 19 Apr 2016 06:59:52 +0000
I`m also requesting you to submit a detailed technical sheet with complete dimensions for your purpose. I don`t really get what you expect to do from a low res picture. There are lots of designers who can model something like that, but please give us details, dimensions etc.

Thanks
Fri, 15 Apr 2016 03:56:32 +0000
Decker are you going to tell the buyer that your submission is an image off of the internet and not anything you created ?
Just curious.

Dipesh

Buyer

Thu, 14 Apr 2016 02:22:26 +0000
Catalin: I am not expecting you to design everything from scratch. I want to see if someone has done something similar for someone else. I will be open to other softwares as well bit will have to see what kind of entries I get. BTW Thanks for your interest in the contest.
Tue, 12 Apr 2016 11:44:05 +0000
First off all Mister Dipesh, if you want a good quality product (because you are asking for manufacturing drawings) you need to give us more information like sink inlet dimension, sewer dimensions, motor dimensions, in inch or in mm? including a very important thing...the shaft of the motor and many more. Based on the information's you offered the best thing that anyone can do is to paint a very nice garbage disposal but hard to manufacture or just copy an existing one. And also you should accept other types of software like Autocad, Solidworks ...including iges and step files.

For 320$ with no info i wish you good luck.

Best regards,

Catalin

Similar Contests on Cad Crowd

Floral Glass Coaster 3D Artwork - STEP
Hi, Im looking for someoone who can design a 3d Product Artwork: Product: 3D Artwork of a round Silicon Glass Coaster Dimensions: Width: 6,5 mm, Diameter: 10,9 cm I have a STL file format, where I started the project, but Im not a professional designer, so I need someone who can maybe start by adopting on my design, as you can find a image attached (IMG1853) and change some things: 1. adopt on the dimensions as written above. 2.add floral structure on the elements/flowers but leaving a straight level at the end. 3. add structure to the buttom and leave here also a straight level at the end. 4.I need a STEP Format at the end. For better understanding I added some pictures of a similar product I would like to orientate on. Also I have a ai Design where you can orientate on the floral structure (see picture attached), but they cant be all taken because the structure is for silicone printin too complex - so the structure needs to be soften up. Please let me know if you can help me with this project. Regards, Jelena.
iPhone/Android Accessory Design Enhancement
This consumer product is an accessory that provides enhanced usability to mobile phones and tablets. The latest design of our "Band" is two parts: 1. Round Base that attaches to the back of the phone (made from a low-friction polymer like polyethylene) 2. A "band" that overlaps with the Round Base (1) and rotates/spins around it. (made from polyethylene over-molded with rubber to provide elasticity to the top band part) The rubber part of the band elongates so that an individual's finger can be placed underneath the band and above the base. The elasticity part is important so it can accommodate different finger sizes. The product allows users to hold the phone more securely. Our current challenge is the design of the "Band" (2). This is where we need the help. As shown in the attached STL file for the Band, there are two circles on either side of the flap that holds the finger down. These circle were put there to provide some added elasticity to the rubber piece. While it does functionally work well, the current design does not look durable or very elegant. We'd like to rethink the band design to make it look incredibly user-friendly, allowing the band to stretch upright to accommodate different finger sizes, while being functionally superior to the current design. Designer will need to provide STL files for my prototyping company to be able to work with.
Where there's muck there's brass
An alternative to picking up dog dropping with plastic bags. A cheap, easy to build, bio-degradeable design. It should, with a minimum of moving parts, (ideally 1-2 piece cardboard structure), pick up and enclose droppings. Should also include built in handle (reasonably distanced from holding section) Simplicity is key. As will need to be able to produce cheaply in large volumes. MUST BE MASS PRODUCEABLE for cost in the region of $1-2.
Unicycle
Hi all, thanks for checking out my contest! I am involved with a company that is looking to receive some entries for a "prototype" electric unicycle. If you aren't familiar let me give you a brief background. Remember the hoverboards last xmas?? The electric unicycle works on essentially the same principle (upside down pendulum theory) to achieve self balancing capability. The current offerings on the market just don't cut it, the plastics are basically thrown together around the requirements of a build, rather than incorporating the necessary components into the design for a smooth finish. I would like the final product to be somewhat futuristic/prototypish looking, maybe a bit sporty. You can get a feeling for whats out there by doing a google search for "electric unicycle". Integral to the design there are 3 requirements. 1.) Obviously the plastic fairing will need to have a cavity for the wheel, but in addition, it will need to subtly include a space for lipo batteries, (doesnt have to be in any particular shape however), and also must include spot for a pcb control board. Both of these items arent excessively large, the PCB is about 4X3 inches and the batteries are about 5X5X1 (but can be reconfigured). 2.) I would also like to incorporate into my design a headlight, and a tail light if possible, but most concerned with head light. Would also like to leave the option open to include small bluetooth speakers, however these would not take very much space at all. 3.) Finally, this design will need to have a retractable handle for balance when getting on/off.
Faith Based Jewelry_1_Christianity
We are a start up launching a line of jewelry based on faith/religion. We are looking to launch with a number of necklaces and bracelets so we are looking for highly innovative designs for pendants and bracelet charms which signify faith based meaning. We want our jewelry line to be worn everyday (not just on occasions) as a charm so that one is never without the blessings of one's faith. We want it to be an essential companion to a user, through thick and thin, to give them the reassurance that one is never alone. We expect: 2 designs for necklace pendants 2 designs for the bracelet charms The designs should be made for metal (sterling silver).