PDF to SolidWorks

Contest Ended, Winner(s) have been selected.
Convert PDF to Solid Works 14
In accordance with drawing.
  1. SolidWorks


1st Winner
#20 Opposite Pad by CADmate
Native and accurate
2014-05-09 04:59:38
#5 Pad by CADmate
This was done in Solidworks 2014 native and accurate.
2014-05-07 10:21:55
#1 Pad from .pdf to SW2014 by Antanas
all parametrical model - you can correct all dimension. Please note the dimension of 0.25 in at top of pad - in model are 0.24 in.
2014-05-07 09:27:44
#2 PAD-2 by Antanas
all dimensions of the model corresponds to drawing pdf
2014-05-07 09:36:44
#3 PAD,BEAM by Vishal
The attached part is created in Solidworks 2011.
2014-05-07 09:48:44
#4 Pad by Fishc1710x
2014-05-07 10:03:15
#6 Part. by Keep
2014-05-07 13:15:37
#7 Drawing by Keep
2014-05-07 13:16:53
#8 149162PAD by Matt N.
2014-05-07 13:37:06
#9 Pad Beam by Randima Gajanayaka
This is quite easy. I have completed this with in several minutes. Thank you.
2014-05-07 15:23:29
#10 1399434807BMLDWG_149162PAD by Shishir
2014-05-07 16:20:25
#11 PAD, BEAM by Kevin Dobson
2014-05-07 16:23:18
#12 PAD_BEAM by Rares Cristian
according to the drawing uploaded
2014-05-07 20:06:49
#13 BMLDWG 149162PAD - SolidWorks 2014 by Atanas Ivanov
Model is designed strictly with the dimensions shown on the drawing at the PDF file.
2014-05-07 21:00:17
#14 149162 Pad by jamesmech
Nylon 6/6 Black Pad
2014-05-07 23:00:07
#15 PART 04 by Prem
I uploaded the file as per your PDF, please appreciate my design. This was created by SW 2012 version, but you can open the files in 2014 also.
2014-05-08 05:15:25
#16 solidworks part file by Jay M.
Solidworks 2014
2014-05-08 05:41:34
#17 design1 by ezer153
2014-05-08 06:51:22
#18 Beam by Slava
2014-05-08 07:28:41
#19 149162 Pad Beam by Mathis Consulting
part only. SolidWorks drawing file can be delivered upon request
2014-05-08 17:36:25
#21 PAD,BEAM by CadOasis
Created in SolidWorks 2014 : In accordance with drawing.
2014-05-09 10:33:21
#22 BMLDWG 149162PAD - Corrected Variant by Atanas Ivanov
In this version, I have added one feature, which I have missed in the previous.
2014-05-09 19:24:42


Thu, 08 May 2014 15:47:51 +0000
Do you just want the 3D model or the part file and drawing file?
Wed, 07 May 2014 20:07:02 +0000
Dear sir ,
if possible i can submit file in .stp or .iges format both will open in solidworks14
Wed, 07 May 2014 12:17:36 +0000
Dear sir, Can I make design on Cimatron or Unigraphics software?
Wed, 07 May 2014 07:10:07 +0000
Is SW2012 accepted?

Similar Contests on Cad Crowd

Smart Wristband
I'm a tech&des student in the UK. I've been able to get by without being great at CAD but this year is unavoidable. My project is a wristband designed for old people that can track where they are and their heart rate. This project will be straight forward for anyone familiar with solid works 2013, neeed it by the next 2 days, (due on wed)
solidwork surface modeling
i have a lot of work solidwork surface modeling. I need expert freelancer.
Mechanical Engineer to develop light guides or light pipes used with LEDs
Looking for an engineer that has experience with light guides or light pipes used with LEDs, and that can design a few simple light guides for an electronic device. 3 LEDs - red, green, blue will feed the light pipe. the other end of the light pipe will be visible to the user thorugh a cutout in the enclosure. the user will see this end of the light pipe, which is 2 strips each at .2 wide x 2" long. there may be some curvature to these 2" long strips (maybe a radius of 2.5"). when the red LED is on the strips will light up red. same for green, etc. need to make sure the lighting is continuous (not brighter at one end than the other). Proven experience with LIght pipes is required. $100 for initial sketch and background proving that this design will work. Further work would then be given to winner to develop the concept into a injection molded part. Good Luck and I look forward to working with you.
Double-sided Clamp Redesign
Double Sided Aluminum Clamp. Need redesign of part to make it easier to manufacture on CNC mill. Currently, the easiest method is waterjetting the clamping profile before finishing on the CNC mill. We would like to make the manufacturing easier and all in one MILL.
SolidWorks Simple Box with 2 Cords - Freelance 3D Designer Contest
Keep the dimensions of the box exactly as they are in the 2D version (they are in imperial but can be changed to metric in the solidworks file) I'm looking for a clean 3D Solidworks file of the exterior with the 2 cords that can pull out almost to look like an assembly drawing in Solidworks. I'm not looking to get detailed on what the product is or how it will work, but the top port is a Micro USB, and the bottom port is a Lightning USB. The notches on both are for fingernails and a cord will pull out. There is a very small power button on the bottom and 4 LED lights on the back side that I will update soon. I'm looking for conceptual nice looking design to use for sale of the product.