Rising Stairs

in Mechanical Engineering held by Aly
Contest Closed
  • Open
  • Choosing Finalist
  • Ended
Design a four-step set of stairs that can go flat at the to or bottom of the stairs, lift a person and wheelchair either up or down, and then take the normal stairs form. Stair lift must be able to operate from either the top or bottom of the stairs. See attached picture for desired end product.
Efficiency of elegance of the design.
  1. 3D PDF Files


= Buyer's Rating


Fri, 06 Apr 2018 11:15:28 +0000
you want the same design in the picture or not.
and you didn't pay for this sir.

Rishi Gangwar


Sat, 24 Mar 2018 13:33:27 +0000
The project is almost complete but please increase the price and specify the capacity to carry, it is vital in order to complete its last phase and for me to finally submit.
Sat, 24 Mar 2018 06:52:47 +0000
and plz provide some technical details i.e weight,height etc
Sat, 24 Mar 2018 06:51:18 +0000
i can do it with electrical equipment but kindly increase design cost at-least $300-$400
Sat, 24 Mar 2018 05:57:45 +0000
Hello Aly
How much is the height from the yard to the floor?


Sat, 24 Mar 2018 04:35:12 +0000
Please explain how to build a product with maybe patent protection? And...the development of the product will take not les than 2 months ant will cost just for the engineering not les than 10.000 Euro. So? Do not be so naiv please! However we speak about mashinery and transportation ot peaple, the requirements are not joke,



Tue, 20 Mar 2018 22:28:37 +0000
This product is only available in the UK. I'm trying to build this in my house for my son. It will not be a commercial product, just something that I can contract its design and build. My intention is to have three contests: 1) Engineering Drawing, 2) Engineering Design, including materials, electro-hydronic mechanizm and operations, and 3) Build.
This context is for the first step, the drawing only



Tue, 20 Mar 2018 13:14:51 +0000
Do u need electro-hydraulic operation?
Tue, 20 Mar 2018 03:29:37 +0000
I am prepare to work on this project.
Mon, 19 Mar 2018 19:49:34 +0000
This is not a DIY project. This is serious engineering with liabilities and patent infringement possibilities.
I agree with both comments before me which should explain why this is not a pre-pay as well.
Mon, 19 Mar 2018 19:00:43 +0000
How is this a contest? It looks to me like a reverse engineering job. Something that is already available. You might want to check if there is a patent on this product already.
Mon, 19 Mar 2018 15:26:01 +0000
An interesting project, but it is worth a lot more than $100!

Similar Contests on Cad Crowd

Underground Refuge Chamber
Design an underground refuge chamber for hardrock mines.
3D modelling and mechanical design
the mechanical properties values will be used to find the proper material and 3D printing process, after identifying the best process and material , a FEA simulation is required to be performed to check if the material and process were chosen are selected correctly and can withstand the actual forces and load applied on the product ...
Designing a Gear lock mechanism
I have two simple spur gears that I want design a lock mechanism for them. The lock shall be engaged with one of these two spur gears and prevent rotation in both directions (both CW and CCW). The lock mechanism shall be triggered easily with a signal or a servo or similar method upon the request of operator to lock gears. The lock mechanism should be able to released easily and with simplicity.
3d insulator drawing in segments. with hollow internal section.
Air Conditioning project - Cooling Loads of FIU Solar Houses
To help you get started on the RTSM for the project, I would like to point out that detailed explanations about the procedures used in the example spreadsheet can be found in the book attached along with the project description: *Example 8-16, pp.266-272* Please follow the instruction to understand how it is implemented. You might need to refer Chapter 7 for the solar heat gain, such as equation 7-32. Once you understand the example, The project should be much easier. Please let me know if you have any questions.