Robotic Enclosure

Contest Ended, Winner(s) have been selected.
Description:
Hello,

I have attached a blender file that has two objects in the file. The intention of this project is to create an enclosure for a robot. The circular object is the base which will go on top of the robot, the chassis is this (mm), I believe i have already adjusted the initial enclosure to fit on top of the chassis but please verify.

image.dfrobot.com/image/data/DFR0310/Upper%20plate%20V1_Layerout.pdf

I would like the chute object to be mounted on top of the enclosure, where a marble will sit in the chute and when the robot spins, the marble will slide down the chute.
Wants:
Design must be a clean and uniform design. It must be able to fit on the chassis size that is linked.

Other software can be used but PLEASE submit a stil file for 3D printing and a blender file with the model. Also, keep it simple!
Software:
  1. Autodesk Inventor
Additional Information
Forgot to list the PREFFERED CAD SOFTWARE:

BLENDER, but I am open to all other software.

Update 1:
Referenced to the comment regarding the dimensions and blender scaling, I do not want the enclosure to be EXACTLY the same size as the chassis (in terms of the diameter) I want the enclosure to be slightly smaller (that is why the enclosure is ~115mm).

I have also attached the pictures of the robot to help with the design of the enclosure.


Entries

1st Winner
#2 Robotic Enclosure by Adam
Mar 14, 2017 19:53
#1 Robotic Enclosure by Adam
Diameter of sphere changed per your requirement. Preparing for the combine ......
more
Mar 14, 2017 18:57

Discussion

Tue, 14 Mar 2017 19:15:12 +0000
Can you upload the 3d model in OBJ or 3ds format?

Adam

Designer

Tue, 14 Mar 2017 18:58:33 +0000
is a 2mm wall thickness ok for the final model ?

j23huynh

Buyer

Tue, 14 Mar 2017 18:13:25 +0000
Hey Design-for-UX

I've attached pictures of the robot and ideally i want the chute to mount on top of the sphere structure. Make any adjustments necessary to make it one model after melding them together. I do not mind if the sphere is slightly changed/molded to accommodate the chute structure.

j23huynh

Buyer

Tue, 14 Mar 2017 17:54:52 +0000


Hey Adam,

You are correct the outside diameter is 115, I actually made it exactly 115. as I do not want the enclosure to completely rest on the edge of the object. I am open to complete remodels but I thought it would be easier to submit designs I currently have.

GKG

Tue, 14 Mar 2017 17:42:52 +0000
Can you please share any image or rough sketch about the final model you are expecting.

It certainly helps all.

Thanks,
GG

Adam

Designer

Tue, 14 Mar 2017 17:22:44 +0000
Your blender file requires it to be scaled down by a factor of .1 (point 1) to get close to intended size.
After that, the inside diameter of the sphere only measures 110.5 and the outside diameter 115.
This means the board image your provided in the pdf link wont fit in the base.

You're probably better off having someone remodel both parts. Conventional CAD systems don't have a blender export option, but you can export to STL.

Similar Contests on Cad Crowd

childrens playground
childrens playground, just a simple base with 3 activities, a slide off of one side, a tunnel slide off the other, and a pole with two swings off the other.
Simple Wristband Attachment Accessory
This contest is to design a very simple wristband attachment accessory piece that can hold a piece of fabric that was cut in a circle. The overall shape of the piece is a football/oval shape. I am attaching some pictures to show a prototype that I made out of paper. There should be 2 triangle shaped holes on the 2 ends that I can attach the piece to. There should also be an inner circle where I can glue the circle cut of fabric. The inner circle should be indented about a millimeter inward from the flat surface to place the cut of fabric. The inner circle should also be 1/2 inches in diameter. There should also be an outline around that inner circle that is flat with the front surface and that outline circle should be a diameter that is about 6 millimeters wider than the inner circle. The overall piece should be about 1.25-1.5 inches long in width from end to end and about 5/8 inches in height from the tallest point in the middle of the piece. All of these measurement can be changed if needed to make the design better, but the inner piece that fits that fabric should be able to comfortably fit a piece of fabric that is 1/2 inches in diameter.
Dice
I need to make dice candy so I need a 3D print out of dice that are 10 dice across and 10 dice high which will give me a 100 dice mold. I will pour food grade silicone around the 3d printout and use that for my candy mold. The file I have here for the dice is too large so I need it redrawn so that I can get the 3d mold made.
Ring design with branches and bramble
We are looking for a ring that will eventually be printed in sterling, featuring bare branches. Ring band needs to resemble a branch (or branches), and the top of the ring needs branches wrapping about it. Inside this ring we'll be adding an element later, so we need a pocket underneath the branches that will fit an item that is approx 5mmx20mm. The design sketch shows a bit of a lip to the pocket from the side view, this will help keep the item in place. Once the design is approved, we'll need it in US sizes 5-13.
Rosh
A small, rectangle tag, with a logo on it, and a hole on one side.