Sketch drawing to CAD/.stl file
in
3D Printing Design
held by
KDDG
Last seen:
2013-09-11 21:42:57
Contest Ended, Winner(s) have been selected.
Description:
Need the sketch/measurements of each unit converted into a CAD drawing so we can have a 3D prototype printed.
Wants:
Will need CAD based on measurements provided. IMG 1- Thickness of material on partitions inside box should be 1/8 of an inch thick. Outer box needs to be 1/4 inch thick. Front needs to be open to insert product into each square. Back must be solid
IMG 2- Internal matierial needs to be 1/8 of an inch thick, outer box 1/4 of an inch thick. Front must be open, back must be solid.
Software:
- AutoCAD
Additional Information
IMG2- outer box needs to also be 1/8 of an inch thick, not 1/4.
Prepaid PrizeEntries
#26 1/4 and 1/8 inch thick box
by SSK
CAD models using CATIA software are done and one file is in igs format.
Sep 1, 2013 13:59
#18 PLASTIC PRODUCT HOLDERS FOR__Sketch drawing to CAD/.stl file
by MoodyDesigns
Download Files
- Autodesk Inventor — IMAGE 2 1.0SHEET
- Autodesk Inventor — IMAGE 1 1.0SHEET
- Autodesk Inventor — IMAGE 1 1.0
- Autodesk Inventor — BOTH ANGLED IN
- Autodesk Inventor — ONE AND ONE
- Autodesk Inventor — ANGLED IN
- Autodesk Inventor — IMAGE 2 1.0
- Autodesk Inventor — IMAGE 2 1.0
- Autodesk Inventor — IMAGE 2 1.0SHEET
- Autodesk Inventor — ONE ONE
- Autodesk Inventor — ANGLED IN
- Autodesk Inventor — IMAGE 1 1.0
- Autodesk Inventor — IMAGE 1 1.0SHEET
- Autodesk Inventor — IMAGE 1 1.0SHEET
- Autodesk Inventor — IMAGE 2 1.0SHEET
Simple small plastic product holders.
Aug 27, 2013 2:40
#6 Sketch drawing of CAD/.stl file
by astonetech
The rendering is done with clear plastic,fpr both the drawing.
Aug 18, 2013 8:26
#12 Box
by Chairul Rijal
I have to entries two times, because the first one have an error when I upload .pdf file that contains all design preview that I made. This entry are the complete file.
Aug 19, 2013 14:12
#2 3D BOX-HANG
by cadmec
3D BOX WITH 36 COMPARTMENTS DESIGN MADE TO HANG ON WALL. THICKNESS OF ALL SIDES, INSDES AND BACKSIDE ARE 1/8".
Aug 17, 2013 14:02
Discussion
I Have Submitted New Design..
Thanks
:)
Thanks
:)
Can you please send a drawing of IMG 2 without the 2 holes in the back?
Similar Contests on Cad Crowd
Simple Wristband Attachment Accessory
This contest is to design a very simple wristband attachment accessory piece that can hold a piece of fabric that was cut in a circle. The overall shape of the piece is a football/oval shape. I am attaching some pictures to show a prototype that I made out of paper. There should be 2 triangle shaped holes on the 2 ends that I can attach the piece to. There should also be an inner circle where I can glue the circle cut of fabric. The inner circle should be indented about a millimeter inward from the flat surface to place the cut of fabric. The inner circle should also be 1/2 inches in diameter. There should also be an outline around that inner circle that is flat with the front surface and that outline circle should be a diameter that is about 6 millimeters wider than the inner circle. The overall piece should be about 1.25-1.5 inches long in width from end to end and about 5/8 inches in height from the tallest point in the middle of the piece. All of these measurement can be changed if needed to make the design better, but the inner piece that fits that fabric should be able to comfortably fit a piece of fabric that is 1/2 inches in diameter.
MOLDS for 3D design
I am making some molds to be used to make pendants and Pyramids cast in resin. I attached the examples drawn to the best of my abilty hopefully you can see it in 3d. Pretty simle actually
Rosh
A small, rectangle tag, with a logo on it, and a hole on one side.
childrens playground
childrens playground, just a simple base with 3 activities, a slide off of one side, a tunnel slide off the other, and a pole with two swings off the other.
Design children's bedroom accessories
make 3d designs of children's bedroom interiors. design a door handle and a coat hook.
Can use any software you prefer.
Gundhi Asmoro
Designer