Vertical water tank with exclusive design in 3D
in
3D Modeling Design
held by
rodrigorodrigues
Last seen:
2017-09-11 23:39:16
Contest Closed
Description:
I need a design for a tank water reservoir for use indoors in small space.The tank needs to be modern, clean and unique design.
The tank must be upright to be used in the corner of a kitchen, in a bathroom, near the garden, etc.
The tank capacity is 200 liters of water.
Measurements:
Width: 40 cm
Depth: 25 cm
Height: approximately 120 cm, in fact the height can be flexible according to the design of the tank.
Position: Vertical rectangular.
The tank is made of polyethylene roto molding process.
I need definition of a good design to hire a company to create the manufacturing mold tank.
I discovered with a manufacturer that the tank is flat it has the problem of stewing because of the weight of water, so it needs to have details to reinforce their structure without stewing when full.
Opening to 15 cm in diameter cap on top.
The center tap height of 40 cm
Opening the side near the floor to the total arterial runoff of water that may also be used to interconnect a second tank.
Wants:
I will choose the best design.Best concept, exclusive and unique design.
Clean and practical to use.
Don't Wants:
Coarse and simple product.
Ask for Sample:
I agree to receive proposal without being finalized.
We first analyze the proposed concept.
If the design meet, we can finish later.
Software:
- AutoCAD
- SolidWorks
Additional Information
I I was wrong at the height of the product.Consider only the width and depth measurements, the height can be flexible.
Width: 40 cm
Depth: 25 cm
Capacity: 200 liters
Height: flexible, according to the drawing.
Payment PendingEntries
#33 Classic column
by Flaviano Crespi
Model inspired by the linearity of greek columns.
Oct 13, 2015 20:31
#32 Drop_VWT
by TIC
Reinforcement: groove and hole
Low connecting hole.
Minimalist design
Low connecting hole.
Minimalist design
Oct 13, 2015 17:44
#30 Simple Water Tank
by Saaddin N.
Simple Water Tank is a tank water reservoir for use in the corner of a kitchen, in a bathroom, near the garden. Simple Water Tank was created from idea to design in October 2015 for the Design Contest for Engineers held by Cad Crowd. The Water Tank had to be modern, clean, and
unique design. Therefore, the design of Simple Water Tank aims to make it looks like a
decoration.
Simple Water Tank capacity is 200 liters of water, with 40 cm width, 25 cm depth, and 230 cm height. The tank position is vertical rectangular. It is made
of transparent polyethylene with the rotational molding process. Transparent color chosen in order to meet modern, clean, and unique design concept, also to facilitate monitoring of water level and water clarity. The arc radius in every corner of Simple Water Tank is 5 mm to meet the requirement for the rotational molding process.
Simple Water Tank has 15 cm in diameter cap on top for water inlet. It also has water outlet on the side near the floor to the total arterial runoff of water that may also be used to interconnect a second tank. Simple Water Tank have details to reinforce their structure to prevent stewing when full.
unique design. Therefore, the design of Simple Water Tank aims to make it looks like a
decoration.
Simple Water Tank capacity is 200 liters of water, with 40 cm width, 25 cm depth, and 230 cm height. The tank position is vertical rectangular. It is made
of transparent polyethylene with the rotational molding process. Transparent color chosen in order to meet modern, clean, and unique design concept, also to facilitate monitoring of water level and water clarity. The arc radius in every corner of Simple Water Tank is 5 mm to meet the requirement for the rotational molding process.
Simple Water Tank has 15 cm in diameter cap on top for water inlet. It also has water outlet on the side near the floor to the total arterial runoff of water that may also be used to interconnect a second tank. Simple Water Tank have details to reinforce their structure to prevent stewing when full.
Oct 12, 2015 22:51
#29 Concept 1
by PETER LAKATOS
The surface of the model is symmetric to the sides, the shape gives it strength, to hold the shape and also look smooth modern and unique
Oct 9, 2015 20:04
#28 Vertical water Tank
by SaketCad
Vertical water tank designed in Solidworks 2012
Oct 9, 2015 13:12
#26 Vertical water tank with exclusive design in 3D
by REDA
thank you for your feedback
Oct 9, 2015 10:38
#24 Water Tank
by Diogenes Bezzi
Water tank to be finalized according to customer preferences / notes.
Oct 2, 2015 20:50
#17 Modular-stackable water tank system
by Bogdan Andrei
The system comprises in a series of smaler water tanks, which are designed to fit one in top of the other one(s), having a self aligning male-female connector type. Using this system will be more easier to implement it in mass production, give the end-user more flexibility, and reducing manufacturing flaws to minimum. The entire system comprising in a certain numbers of modules, will sit on a ground support, where a pump and other devices could be hiden, along with the pipe connectors and fittings.
Sep 12, 2015 15:15
#16 water tank curve shaped
by abdillah yusuf
water tank with 200 L capacity.. suitable for minimalist home interior
Sep 12, 2015 6:37
#11 Vertical Tank
by Irfan
Capacity=200 Litres.
Easy Roto Mold .
alphacad.tk
alphacadco.weebly.com
Easy Roto Mold .
alphacad.tk
alphacadco.weebly.com
Sep 4, 2015 6:55
#10 Vertical water tank with exclusive design in 3D
by abdillah yusuf
watertank with stream cutting line design
Sep 2, 2015 6:24
#9 Vertical water tank with exclusive design in 3D
by REDA
Thank you for you confidence ;)
Aug 27, 2015 9:14
#6 Vertical water tank
by J. Lentowicz
Sir
This is my concept for you water tank. It meets all requirements set forth by you. If you have any question please contact me.
Thank you
This is my concept for you water tank. It meets all requirements set forth by you. If you have any question please contact me.
Thank you
Aug 26, 2015 17:58
#3 VERTICAL TANK CP-1
by DesignerRavi
Sir,
This concept is designed as per the dimensions but instead of using 120cm height i have used 160cm, if you want me to change i can change.
All the files are attached in zip folder please find the attachment.
Thank you.
DesignerRavi
This concept is designed as per the dimensions but instead of using 120cm height i have used 160cm, if you want me to change i can change.
All the files are attached in zip folder please find the attachment.
Thank you.
DesignerRavi
Aug 20, 2015 21:22
#1 Honeycomb Reservoir
by Ahmed Mezil
The Honeycomb reservoir design is aimed to achieve the following:
-provide rigidity during water storage (reduced stewing effect)
-smooth surfaces make the reservoir easy to handle
-shell thickness of 1 inch meets rotational molding guidelines
-Aesthetically pleasing
I'd be happy to answer any questions or concerns you may have regarding my design. I can also modify it upon request, if we wish to move forward.
Thank you,
-Ahmed
-provide rigidity during water storage (reduced stewing effect)
-smooth surfaces make the reservoir easy to handle
-shell thickness of 1 inch meets rotational molding guidelines
-Aesthetically pleasing
I'd be happy to answer any questions or concerns you may have regarding my design. I can also modify it upon request, if we wish to move forward.
Thank you,
-Ahmed
Aug 19, 2015 3:26
Discussion
.
The center tap height of 40 cm I don't understand :)
The center tap height of 40 cm I don't understand :)
40*25* height flexible
200 litres
200 litres
I'm sorry, I really I was wrong at the time of the product.
Consider only the width and depth measurements, the height can be flexible.
Consider only the width and depth measurements, the height can be flexible.
i have the same note as @jezdo, your dimensions leading to 120 litres, so you have to edit your order Description
Volume of 40*25*120 cm is 120 Litres, not 200
Similar Contests on Cad Crowd
converting 2D to 3D
We are looking for designers who can make 3d models (in STL format) from 2D images.
The images are furniture or jewelry.
The models should be only the geometry shape (STL) .
There is no need for texture, color or rendering.
We would like to have at least 100 models per week.
Bring our mascot to life! 2D to 3D Design for 3D Printing
Our mascot has lived his entire life as nothing more than a 2D image on a screen. It's very sad, and it's time that changed!
We would like to render our buddy into 3D with the ability to print and assemble him with the new wave of MakerBot 2 3D printers. The output should be an SLA files we can slice and print.
The final piece will be used as promotional material and/or just something around the office.
280Z Hood Scoop
Looking for a 3D model I can use to print or CNC of a hood scoop
Liver Shell
Design should be of a liver shell. It should be an anatomically accurate model that can be printed if needed to. The inside should be hallow and the liver should include a hole on top where the hyper-vein would normally be and a hole on bottom where the vein would leave. The liver shell should be a 2 piece design that can be clicked/ screwed together to symmetrically put together the 2 halves.
http://www.exchange3d.com/3D-Model-of-Liver-Anatomy/prod_28235.html#preview
A more simplified version of this will be perfect.
J-shape
3D modeling of a J-shaped massage tool, much like a Theracane only smaller in dimensions. The tool should be modeled as close as possible to the attached images. The straight portion of the J-shape is approximately 10 inches long and 3/8in in diameter. The hook portion of the tool should form an approximately 180 degree arc and terminate in spherical end of 9/16in diameter. The handle, at the top of the J-shape, should be approximately 3/4in in diameter. The attached jpg images are of the actual tool that I would like modeled and should give you a good idea of it's dimensions. The png file should also provide a good reference. Thanks.
REDA
Designer