In-car vending machine

in Consumer Products held by Melvin32
Contest Closed
Description:
Hi,

I need a technical drawing of a product idea that I would like to send to manufacture's so they can create a prototype.

The idea is an in-car vending machine/box that can fit snacks and other small items. It needs to fit on the middle/center console of the car (example picture attached). I would want a box that is modern/techie.

The box needs to be unique but similar to the example pictures I'm going to attach.

Three main components:
-Main box
-Clear lid
-Dividers

Dimensions:
-Length: 13 - 13.5 inches
-Width: 8 inches
-Height: 4 - 4.5 inches
Wants:
I am looking for unique esthetics and design. Modern and tech focused.
Don't Wants:
Do not copy the example photos, please. It has to be different and unique.

Entries

#35 CarBox by Nikos Papaioannou
The vending box consists of three pieces. The base box, the lid, which is made of transparent plastic and the drawer. Thanks to the push open system, the driver has the ability to open the drawer and access the snacks without losing contact with the road.
more
Mar 16, 2020 15:29
#33 Car vending machine by Sarmad
Box- Plastic
Lid- Acrylic
Rod/pin-AL
more
Mar 16, 2020 12:23
#32 In-car vending machine by Eroms
The design is operated by turning the knob at the top (clockwise or anti-clockwise), and the internal rack and pinion sends the two compartments the opposite way for access.
Material: light sheet metal for the support and the other main components are made of plastic except some fastener.
more
Mar 16, 2020 3:25
#29 Car Vending by Wahyu Gading Krisna
Hi, This is my box design. hope you like it. This box design is unique, because there is a batman logo to attract people's attention
thank you..
more
Mar 15, 2020 20:25
#28 CAR VENDING PROTOTYPE 2 by ariesta
This box is designed with ergonomic rules, the front of the box is made lower to make it easier to take something that is placed inside, and the front is made slightly smaller to give the driver or passenger the flexibility of the seat next to the box ...
more
Mar 15, 2020 9:44
#27 In- car vending with 3 Dividers by Anh Huynh
This box is designed with 3 dividers:
The largest partition can fit snack pack
Two smaller parttition can fit cookies
The smallest parttion will fit candy...
more
Mar 15, 2020 9:21
#26 CAR VENDING PROTOTYPE 1 by ariesta
This box is designed with ergonomic rules and does not forget the aesthetic element ... so that it is easy to put things and take them ...
more
Mar 15, 2020 5:01
#25 Life Box by Panji Hakim
This box can be used to store food, medicine, or other small items. Inside is one larger space for storing larger items. Beside it there is a part to attach the binder. the lid is divided into 3 parts.
more
Mar 14, 2020 23:02
#24 vending box by Phani-Designs
The vending box contains square sections designed to perfectly fit medium size chocolate bars and mints.
It contains a circular section to put random items or small containers/cans.
It also has two magazine holders, on each side.
more
Mar 14, 2020 2:26
#23 car vending by Jim81
Mar 12, 2020 23:36
#22 ICV_1.0 by Rohit Aggarwal
This box incorporates both a cooling box at the bottom and a normal snack box at the top. The snack box can accommodate all types of snacks from chips to biscuits and mixtures. To keep the cool snacks cold, the separate chill box at the bottom is provided with space for a can and some chocolates. The main requirements have been adhered to, which includes Main box, Clear Lid and Dividers. A sturdy handle is provided at the top for easy placement and shifting. The hinges are easily openable yet snug, and a seal is provided in the chill box for good sealing. Tech-wise the box has a cooling compartment, which can be powered by the car charger, along with compatibility for lighting inside the box and USB and power socket. After approval, the technical drawings will be made clear for easy and fast manufacturing.
more
Mar 12, 2020 13:19
#20 in car vending machine by SML95
hi,
this type of vending machine is better placed behind the driver's seat.
more
Mar 10, 2020 15:30
#19 in-car vending machine by SML95
Hi,
this is my design, it has compartiments ables to fit different snacks, a main bos that holds it all together and it has parts to strap it in the car. if there is any modifications that you would like send me your feed-back.
more
Mar 4, 2020 11:10
#18 BellaBox by Tiodora
Mar 4, 2020 8:42
#17 Concept design for Vending box from VEAS by Vijayakumar
Hi,
This is a concept design. It contains 3 parts. I can send you the Engineering drawing for these parts if you interested.
We are looking forward your positive result.
Thanks and regards.
Vijayakumar
more
Mar 1, 2020 10:17
#16 Car Vending Box by Artificer-kbg
This is a car vending box made up of clear plastic. it consists of a lid that can be opened by the driver from the front. It also consists of a cup holder in the back towards the passenger so that he/she can put a cup over there.
also the slant dividers helps to keep the product in such a way that it is visible to the passenger sitting in the back. Also these slant divider can help you keep items having height more than 4.5 inches (that is the maximum permissible height for the design). this is just a model with outer design features, if you like we can design a complete product for you with additional features.
more
Feb 28, 2020 14:05
#13 Car Vending machine by Muntazir Merchant
The design consists of 2 main containers. Each of the containers can be divided in different ways depending on requirements. It has an adjustable divider for the compartment division. It has sliding doors so it doesn't restrict the drivers "rear" view or hand motion and also isn't susceptible to damage.
Please review my design so I can improve on it. Thank you :)
more
Feb 21, 2020 6:05
#11 IN CAR VENDING SNACKS by ROCKY17
All the requirement measurements is base on your needs
Please see the attachment
Multi configuration rack design
Easy to use for supply and take the favorite Snack
THANK YOU
more
Feb 20, 2020 7:00
#9 vending by Oggy
Feb 18, 2020 16:57
#8 Utility Box by Rajat0101
Dual opening leads, removable separators and a simple design makes it more subtle.
more
Feb 15, 2020 9:20
#6 In-car Vending Machine by Raza Imam
Feb 14, 2020 15:13
#5 Car vending machine by Sarmad
Box- Plastic
Lid- Acrylic
Rod/pin-AL
more
Feb 14, 2020 14:58
#4 In car vending by KAHA5CADi
The cad drawing from plastic and acrylic lids
more
Feb 14, 2020 13:52
#3 IN-CAR VENDING MACHINE by SML95
this car vending machine has two sliders to put snacks in them, as well as compartiment for bottles, cans ..., the lid is clear so that you could see what is inside the box. all the parts could be made by plastic injection molding, the lid can be made with clear plastic.
more
Feb 13, 2020 20:10
#2 In-car Vending Machine by Eroms
This is the first draft of the design, updates coming soon.
Main material list/choice for several parts of the component :
1. Solid frame- Plastic
2. Clear components - Acyrlic
3. Channel - Aluminium bar
more
Feb 13, 2020 6:42
#1 in-vehicle_box_model_P by Pop Horea-Vasile
Designed in licensed ViaCAD_v10, under Linux Ubuntu 19.04.
more
Feb 8, 2020 22:55

Discussion

Eroms

Designer

Fri, 14 Feb 2020 14:18:11 +0000
Please can the submission date be extended?
Tue, 11 Feb 2020 04:53:32 +0000
My team will crush this design, help you prototype it, create pre-production units and select a manufacturer - mass production or small volume. We are new to Cad Crowd, but have a Product Development firm with a wealth of experience. This is a great idea, and posting it like this puts you in a race to get to market. We can help.
Sat, 08 Feb 2020 08:35:04 +0000
I can think of three to five different ways of doing it.. and I could produce a prototype. Not really going to hand over at design for a chance to win two hundred bucks? Kind of an interesting little product though.
Fri, 07 Feb 2020 17:57:33 +0000
I would request you to prepay.

Similar Contests on Cad Crowd

Silicone Toddler Placemat
We want to make a silicone placemat for toddlers with extruding bowls (probably 3 bowls). The shape should be a dinosaur (maybe stegosaurus or t-rex). Please see attached elephant for an idea of what we are looking for. Simple yet elegant and appealing. The mat size should be 10"x7.7"x1". The bowls should comprise most of the mat, besides perhaps a 1" to maybe 1/2" border. The edges should allow for spilling a drink and the liquid would not run onto the table. Past the raised edges though, the mat should slope down towards the table. The idea is that the toddler (or even adult really) cannot get his fingers underneath the mat because it slopes towards the table. We also need a small credit card style tool to lift up the mat since it will basically be impossible to pull up from the table once you lay it down.
Protective Dog Vest - Project for Antanas
As discussed with Antanas
Ultra Creative Frame for 11x14 Paintings
Hello! This is my first attempt at a campaign and hoping to use it as a launching pad for more work. For this project, I'm an artist that needs ultra-creative unique painting FRAMES to surround 11x14 single-sheet paper. I'd love the FRAMES to be part of the painting itself, not just a separate accessory that goes on the wall. I'm looking for the absolute most over the top beautiful, gorgeous, creative ideas for what I can only describe my work to be abstract, splatter type. **** I've included some of my paintings as examples. *** I included an origami paper flower I made, with the type of paint splatter that will not only go into the final paper but the FRAME itself.
Two-Piece Plastic Shot Glass Design with Screw Threads
(See attachment for figure drawings) Shot glass shape (will be plastic moldable) with sloped/curved upper region (Fig. C) 90mm in height, fully assembled (Fig. C) 52 mm diameter at the top; 35 mm diameter at the bottom (Fig. C) Desired wall thickness: 2 mm 2 pieces (Fig. A and Fig. B) screw together to form the item (Fig. C) Top piece (Fig. A): Height of 20 mm plus 5 mm male threads (we are flexible on the dimensions of the threads based on designer’s expertise) The brim should be rounded Bottom piece (Fig. B): Height of 70 mm includes 5 mm of corresponding inner female threads at the top The objective is to create an inner chamber when the two pieces are screwed together that will hold in a solid piece, but allow liquid to flow through. This should be achieved by having the bottoms of both pieces include a stylized, wavy “grate”. (Fig. D).
Playful & Fun Inspired Taco Holder
We need you to redesign the look of the taco holder (photo attached) to be even cooler, sillier, ridiculous and something everyone would want in their pantry. The most imaginative, hilarious and irresistible design wins!