Light bulb with thread on

in 3D Printing Design held by Ingeborg Rosenvinge
Contest Closed
Description:
We need a light bulb with thread on - for 3D printing. We are a thread cutting tool company, and for making a commercial we need a light bulb with threads all the way to the top.
Wants:
It has to be nice and printable. I attached a commercial for beer with a light bulb. It should be easy to find a model where the thread can be attached.
Don't Wants:
Poor design
Software:
  1. Autodesk or toher

Entries

No Entries Submitted Yet.

Discussion

Wed, 19 Apr 2017 15:40:31 +0000
@Lucian,

Thanks for your quick response.

Lucian

Administrator

Wed, 19 Apr 2017 15:35:55 +0000
Hi,

The contest will be closed until the buyer will prepay the contest, since he didn't prepaid and selected the winners for his previous contest.

Lucian
Wed, 19 Apr 2017 15:17:31 +0000
Your previous contest also ended without selecting a winner and also a payment pending.
Wed, 19 Apr 2017 14:52:35 +0000
please make a Prepaid Prize
Wed, 19 Apr 2017 14:51:34 +0000
Incandescent bulb or led bulb?

Similar Contests on Cad Crowd

Ring design with branches and bramble
We are looking for a ring that will eventually be printed in sterling, featuring bare branches. Ring band needs to resemble a branch (or branches), and the top of the ring needs branches wrapping about it. Inside this ring we'll be adding an element later, so we need a pocket underneath the branches that will fit an item that is approx 5mmx20mm. The design sketch shows a bit of a lip to the pocket from the side view, this will help keep the item in place. Once the design is approved, we'll need it in US sizes 5-13.
Rhombicuboctahedron
Design two symmetrical Rhombicuboctahedrons (Rohm' for short) for printing on Prusa 3D MK2. The 1st Rhom' needs to be made of 2 parts that can be connected to form the complete shape. The width of the Rhom' should be 100nn from face to face. Each edge of this Rhom' needs to have a 5mm high 'fence' sticking outward. Two inner benches or plates need to be constructed in the inner space of each of the halves. The 2nd Rhom' is also made of 2 parts but without fences and without benches. It is a simple Rhom'. It needs to fit exactly on the 1st Rhom' from the outside. so that the 1st Rohm' go inside the second one. The attached jpg and max files depict the 1st Rhom'. However the max file is full of mistakes and should not be used as anything but as a general reference. Nor the 'fences' need to be constructed as V shape as in the max files. Please ask me anything which is not clear.
Badge
look for someone to setup a 3d file from png file we are Official MOD Approved Merchandise with over 3000 badge we are an DTG pprinter company but we going into 3d printing and need files for this side of the work please find a copy of one of the badge
Clear Plastic Case
I am looking for a round clear plastic case design to be 3D printed for a prototype. This is very generic. The case should be 4.5 inches in diameter, round tapered off around the edge, and approximately 1 inch thick at the center, tapering off to about .25 inches until edges connect. The front and back should be of equal dimensions and attached by plastic and opens and closes, and snaps closed. The back should be black plasting, and the front should be clear plastic. This case would be very similar to something like a round eyelash case holder, or something that might hold ear buds.
3D Printing Design | Meet the minimum thinkness on two small parts of my 3D STL file for Shapeways!
I need someone to make a certain part of my 3D anchor stl file a little thicker. Nothing complicated at all! The guy that was working on this file is really swamped with work and cannot complete this edit. This job should literally take less than 30 minutes if you know what you are doing. On the attached picture it shows that I need to make specific parts of the anchor a little thicker to meet the minimum supported wire thickness of .8mm. Here's what the email I recieved from shapeways said: "Here is why we cannot print your model: The minimum thickness for free/supporting wires > 1.0mm and supported wires > 0.8mm for this material. Please thicken the wires of the model." I have specified what needs to be done on the picture attached. Please message me if you need clarification. If you know what you are doing and have worked with stl. files and understand the thickness minimum that shapeways requires for 3d printing then this should be a no-brainer.