Description:I'm hoping this is a simple project. I have designed a headband (a variation of the coil soccer headband worn by the likes of David Beckham). This one is for the ladies. The coil (unlike the soccer headband) becomes larger at the crown of the head. I will produce it through 3D printing for myself and friends - so far this is just a personal project. Specs are in the attached jpg.
Wants:I want a smooth transition from the tight coils at the ends to the top of band (crown). The band will be made in metal and needs to be a smooth spiral coil, not angular in any place. I will need a stl file for production. Specs are in the attached jpg.
Ask for Sample:Specs are in the attached jpg.
#1 headband coil spec by Jeremy Benjamin
#2 revision A to my previous entry by Jeremy Benjamin
Here's my 2nd pass at it. It's not perfect, but I finessed the model to be smoother in those transition points than my previous version. The challenge is, I'm using a 3D mirroring function to keep it symmetrical, but when I mirror the object about the mid-plane, then the coil is going the wrong direction, so I get some wonky geometry where I try and bridge that gap. Still brainstorming a way to do this. Hopefully this 2nd try is a step in the right direction...
Similar Contests on Cad Crowd
Design two symmetrical Rhombicuboctahedrons (Rohm' for short) for printing on Prusa 3D MK2. The 1st Rhom' needs to be made of 2 parts that can be connected to form the complete shape. The width of the Rhom' should be 100nn from face to face. Each edge of this Rhom' needs to have a 5mm high 'fence' sticking outward. Two inner benches or plates need to be constructed in the inner space of each of the halves. The 2nd Rhom' is also made of 2 parts but without fences and without benches. It is a simple Rhom'. It needs to fit exactly on the 1st Rhom' from the outside. so that the 1st Rohm' go inside the second one. The attached jpg and max files depict the 1st Rhom'. However the max file is full of mistakes and should not be used as anything but as a general reference. Nor the 'fences' need to be constructed as V shape as in the max files. Please ask me anything which is not clear.
Hello, I have attached a blender file that has two objects in the file. The intention of this project is to create an enclosure for a robot. The circular object is the base which will go on top of the robot, the chassis is this (mm), I believe i have already adjusted the initial enclosure to fit on top of the chassis but please verify. http://image.dfrobot.com/image/data/DFR0310/Upper%20plate%20V1_Layerout.pdf I would like the chute object to be mounted on top of the enclosure, where a marble will sit in the chute and when the robot spins, the marble will slide down the chute.
look for someone to setup a 3d file from png file we are Official MOD Approved Merchandise with over 3000 badge we are an DTG pprinter company but we going into 3d printing and need files for this side of the work please find a copy of one of the badge
Clear Plastic Case
I am looking for a round clear plastic case design to be 3D printed for a prototype. This is very generic. The case should be 4.5 inches in diameter, round tapered off around the edge, and approximately 1 inch thick at the center, tapering off to about .25 inches until edges connect. The front and back should be of equal dimensions and attached by plastic and opens and closes, and snaps closed. The back should be black plasting, and the front should be clear plastic. This case would be very similar to something like a round eyelash case holder, or something that might hold ear buds.
3D Printing Design | Meet the minimum thinkness on two small parts of my 3D STL file for Shapeways!
I need someone to make a certain part of my 3D anchor stl file a little thicker. Nothing complicated at all! The guy that was working on this file is really swamped with work and cannot complete this edit. This job should literally take less than 30 minutes if you know what you are doing. On the attached picture it shows that I need to make specific parts of the anchor a little thicker to meet the minimum supported wire thickness of .8mm. Here's what the email I recieved from shapeways said: "Here is why we cannot print your model: The minimum thickness for free/supporting wires > 1.0mm and supported wires > 0.8mm for this material. Please thicken the wires of the model." I have specified what needs to be done on the picture attached. Please message me if you need clarification. If you know what you are doing and have worked with stl. files and understand the thickness minimum that shapeways requires for 3d printing then this should be a no-brainer.