I will design a custom PCB, schematic and 2 or 4 layer layout for your ESP32 or STM32
About this service
Need a PCB that works the first time you order it?
I'm Mehedi, an EEE engineer from SUST and Vice President of RoboSUST. I design compact, manufacturing-ready boards for ESP32, STM32 and Arduino products. My robot PCB won 1st place at Auto Grand Prix.
What you get:
- Clean schematic, organised in functional blocks
- 2 or 4-layer PCB layout with proper power, ground and signal routing
- DRC and ERC checked, 0 errors
- Gerber, BOM and pick-and-place files for JLCPCB or PCBWay
- 3D view and full source files
Recent work:
- Round 4-layer ESP32-S3 health smartwatch (heart rate, SpO2, BLE)
- Wearable alarm band with LED display and LiPo charging
- USB-C PD power board with STM32 and current sensing
- 11-sensor STM32 line-follower robot board
I work with ESP32, STM32, Arduino, sensors, motor drivers, LiPo charging, USB-C and buck/boost regulators.
Need code for the board? I also offer ESP32/STM32 firmware as a service.
Have a breadboard project? I also offer an Arduino-to-PCB service.
Send me your idea, sketch or circuit before ordering and I'll give you an honest quote.
I'm Mehedi, an EEE engineer from SUST and Vice President of RoboSUST. I design compact, manufacturing-ready boards for ESP32, STM32 and Arduino products. My robot PCB won 1st place at Auto Grand Prix.
What you get:
- Clean schematic, organised in functional blocks
- 2 or 4-layer PCB layout with proper power, ground and signal routing
- DRC and ERC checked, 0 errors
- Gerber, BOM and pick-and-place files for JLCPCB or PCBWay
- 3D view and full source files
Recent work:
- Round 4-layer ESP32-S3 health smartwatch (heart rate, SpO2, BLE)
- Wearable alarm band with LED display and LiPo charging
- USB-C PD power board with STM32 and current sensing
- 11-sensor STM32 line-follower robot board
I work with ESP32, STM32, Arduino, sensors, motor drivers, LiPo charging, USB-C and buck/boost regulators.
Need code for the board? I also offer ESP32/STM32 firmware as a service.
Have a breadboard project? I also offer an Arduino-to-PCB service.
Send me your idea, sketch or circuit before ordering and I'll give you an honest quote.
Need a PCB that works the first time you order it?
I'm Mehedi, an EEE engineer from SUST and Vice President of RoboSUST. I design compact, manufacturing-ready boards for ESP32, STM32 and Arduino products. My robot PCB won 1st place at Auto Grand Prix.
What you get:
- Clean schematic, organised in functional blocks
- 2 or 4-layer PCB layout with proper power, ground and signal routing
- DRC and ERC checked, 0 errors
- Gerber, BOM and pick-and-place files for JLCPCB or PCBWay
- 3D view and full source files
Recent work:
- Round 4-layer ESP32-S3 health smartwatch (heart rate, SpO2, BLE)
- Wearable alarm band with LED display and LiPo charging
- USB-C PD power board with STM32 and current sensing
- 11-sensor STM32 line-follower robot board
I work with ESP32, STM32, Arduino, sensors, motor drivers, LiPo charging, USB-C and buck/boost regulators.
Need code for the board? I also offer ESP32/STM32 firmware as a service.
Have a breadboard project? I also offer an Arduino-to-PCB service.
Send me your idea, sketch or circuit before ordering and I'll give you an honest quote.
I'm Mehedi, an EEE engineer from SUST and Vice President of RoboSUST. I design compact, manufacturing-ready boards for ESP32, STM32 and Arduino products. My robot PCB won 1st place at Auto Grand Prix.
What you get:
- Clean schematic, organised in functional blocks
- 2 or 4-layer PCB layout with proper power, ground and signal routing
- DRC and ERC checked, 0 errors
- Gerber, BOM and pick-and-place files for JLCPCB or PCBWay
- 3D view and full source files
Recent work:
- Round 4-layer ESP32-S3 health smartwatch (heart rate, SpO2, BLE)
- Wearable alarm band with LED display and LiPo charging
- USB-C PD power board with STM32 and current sensing
- 11-sensor STM32 line-follower robot board
I work with ESP32, STM32, Arduino, sensors, motor drivers, LiPo charging, USB-C and buck/boost regulators.
Need code for the board? I also offer ESP32/STM32 firmware as a service.
Have a breadboard project? I also offer an Arduino-to-PCB service.
Send me your idea, sketch or circuit before ordering and I'll give you an honest quote.
Need a PCB that works the first time you order it?
I'm Mehedi, an EEE engineer from SUST and Vice President of RoboSUST. I design compact, manufacturing-ready boards for ESP32, STM32 and Arduino products. My robot PCB won 1st place at Auto Grand Prix.
What you get:
- Clean schematic, organised in functional blocks
- 2 or 4-layer PCB layout with proper power, ground and signal routing
- DRC and E... read more
I'm Mehedi, an EEE engineer from SUST and Vice President of RoboSUST. I design compact, manufacturing-ready boards for ESP32, STM32 and Arduino products. My robot PCB won 1st place at Auto Grand Prix.
What you get:
- Clean schematic, organised in functional blocks
- 2 or 4-layer PCB layout with proper power, ground and signal routing
- DRC and E... read more
Need a PCB that works the first time you order it?
I'm Mehedi, an EEE engineer from SUST and Vice President of RoboSUST. I design compact, manufacturing-ready boards for ESP32, STM32 and Arduino products. My robot PCB won 1st place at Auto Grand Prix.
What you get:
- Clean schematic, organised in functional blocks
- 2 or 4-layer PCB layout with proper power, ground and signal routing
- DRC and ERC checked, 0 errors
- Gerber, BOM and pick-and-place files for JLCPCB or PCBWay
- 3D view and full source files
Recent work:
- Round 4-layer ESP32-S3 health smartwatch (heart rate, SpO2, BLE)
- Wearable alarm band with LED display and LiPo charging
- USB-C PD power board with STM32 and current sensing
- 11-sensor STM32 line-follower robot board
I work with ESP32, STM32, Arduino, sensors, motor drivers, LiPo charging, USB-C and buck/boost regulators.
Need code for the board? I also offer ESP32/STM32 firmware as a service.
Have a breadboard project? I also offer an Arduino-to-PCB service.
Send me your idea, sketch or circuit before ordering and I'll give you an honest quote. read less
I'm Mehedi, an EEE engineer from SUST and Vice President of RoboSUST. I design compact, manufacturing-ready boards for ESP32, STM32 and Arduino products. My robot PCB won 1st place at Auto Grand Prix.
What you get:
- Clean schematic, organised in functional blocks
- 2 or 4-layer PCB layout with proper power, ground and signal routing
- DRC and ERC checked, 0 errors
- Gerber, BOM and pick-and-place files for JLCPCB or PCBWay
- 3D view and full source files
Recent work:
- Round 4-layer ESP32-S3 health smartwatch (heart rate, SpO2, BLE)
- Wearable alarm band with LED display and LiPo charging
- USB-C PD power board with STM32 and current sensing
- 11-sensor STM32 line-follower robot board
I work with ESP32, STM32, Arduino, sensors, motor drivers, LiPo charging, USB-C and buck/boost regulators.
Need code for the board? I also offer ESP32/STM32 firmware as a service.
Have a breadboard project? I also offer an Arduino-to-PCB service.
Send me your idea, sketch or circuit before ordering and I'll give you an honest quote. read less
Service offer categories
PCB Design Services
3D Design Services
3D Modeling
Software & skills
Analog Electronics Design
Electrical Engineering
Electronics Design
Product Development
Schematic Design
+2 more
This service includes
| Service tiers | Simple $25 | Standard $70 | Advanced $150 |
|---|---|---|---|
| Summary | Simple PCB | Product PCB | Advanced PCB |
| Details | - Schematic + 2-layer PCB - Up to 20 components - Gerber files - Source files | - Schematic + 2-layer PCB - Up to 60 components - Gerber, BOM, 3D view - Pick & place file | - Up to 4-layer PCB - Up to 120 components - DFM check + full fab files - JLCPCB order help |
| Delivery time | 3 days | 5 days | 7 days |
| Number of revisions | 2 | 3 | 5 |
Member since
October 2026
Languages
English,
Bengali (Bangla)
Avg. response time
1 hour
PCB design and embedded firmware engineer (KiCad, EasyEDA, Altium, ESP32, STM32)
Need a PCB that passes DRC the first time and is ready to order from JLCPCB? I design 2- and 4-layer boards and write the ESP32/STM32 firmware that runs on them, so you work with one engineer from schematic to working prototype.
What I can do for you:
- Schematic capture and PCB layout in KiCad, EasyEDA or Altium Designer (2 and 4 layers)
- Custom symbols and footprints from datasheets
- Manufact... read more
What I can do for you:
- Schematic capture and PCB layout in KiCad, EasyEDA or Altium Designer (2 and 4 layers)
- Custom symbols and footprints from datasheets
- Manufact... read more
Questions and answers
Your idea, a schematic or hand sketch, the main parts, and the board size if you have one. A rough idea is fine.
Yes. I export Gerbers, BOM and pick-and-place to their specs and check them with DRC before delivery.
KiCad or EasyEDA, whichever you prefer. Altium on request. You always get the full source files.
Yes. I also offer ESP32/STM32 firmware as a separate service.
Cad Crowd Billing Security policy
Service quality is protected by Cad Crowd Billing Security policy.
More similar services
See related services
- 3D Design services
- 3D Modeling services
- CAD Design services
- 3D CAD Design services
- 2D & 3D Design services
- CAD Modeling services
- 3D CAD Modeling services
- 2D & 3D Modeling services
- Engineering Design services
- Drafting services
- AutoCAD services
- Mechanical Design services
- 3D Models services
- Design for Manufacturing services
- 2D Drawing services
- 2D Drafting services
- CAD Drafting services
- 2D AutoCAD services
- Product Design services
- Rendering services
- SolidWorks services
- Mechanical Engineering services
- Architectural Design services
- 3D Rendering services
- 3D Solidworks services
- Manufacturing Drawings services
- 2D/3D AutoCAD services
- Assembly Design services
- 2D & 3D Modeling Solidworks services
- Mechanical Engineer services
- Design Engineer services
- Industrial Design services
- Interior Design services
- AutoCAD Mechanical services
- Product Development services
- FEA services