Remote
Work location
Structural / Mechanical Engineer Needed for Steel Mast Design for Small Wind Turbine Ended
About the job
We are looking for an experienced structural or mechanical engineer to support the design of a steel mast for a small wind turbine project.
This is not a standard catalogue pole. The mast needs to be designed based on specific loading conditions provided by the client.
Project scope:
We need an engineer who can:
review the given loading conditions
calculate the required mast configuration
propose suitable mast diameter / section sizes / thicknesses
advise whether the mast should be 1-piece or 2-piece
prepare a proposal / concept drawing
estimate the pole weight
consider the structural suitability of the mast for this application, including fatigue-related considerations if relevant
Project data provided by client:
Approximate mast height: 13.45 m
Horizontal force from wind turbine at 15 m: 4,900 N
Horizontal force on mast at 8 m: 3,000 N
Wind turbine weight: 320 kg
Material: steel S235 or S355
Surface treatment: hot-dip galvanizing
Application: outdoor use, wind turbine support mast
Manufacturing preference:
Our production is optimized for steel mast sections up to approximately 12 m in length.
For this reason, we are particularly interested in a polygonal steel mast solution, possibly in 2 sections, with an overlap / slip-joint connection if structurally suitable.
However, the engineer may also propose another technically and economically suitable mast configuration.
Important:
At this stage, we need a proposal / concept design only, not a... read more
This is not a standard catalogue pole. The mast needs to be designed based on specific loading conditions provided by the client.
Project scope:
We need an engineer who can:
review the given loading conditions
calculate the required mast configuration
propose suitable mast diameter / section sizes / thicknesses
advise whether the mast should be 1-piece or 2-piece
prepare a proposal / concept drawing
estimate the pole weight
consider the structural suitability of the mast for this application, including fatigue-related considerations if relevant
Project data provided by client:
Approximate mast height: 13.45 m
Horizontal force from wind turbine at 15 m: 4,900 N
Horizontal force on mast at 8 m: 3,000 N
Wind turbine weight: 320 kg
Material: steel S235 or S355
Surface treatment: hot-dip galvanizing
Application: outdoor use, wind turbine support mast
Manufacturing preference:
Our production is optimized for steel mast sections up to approximately 12 m in length.
For this reason, we are particularly interested in a polygonal steel mast solution, possibly in 2 sections, with an overlap / slip-joint connection if structurally suitable.
However, the engineer may also propose another technically and economically suitable mast configuration.
Important:
At this stage, we need a proposal / concept design only, not a... read more
We are looking for an experienced structural or mechanical engineer to support the design of a steel mast for a small wind turbine project.
This is not a standard catalogue pole. The mast needs to be designed based on specific loading conditions provided by the client.
Project scope:
We need an engineer who can:
review the given loading conditions
calculate the required mast configuration
propose suitable mast diameter / section sizes / thicknesses
advise whether the mast should be 1-piece or 2-piece
prepare a proposal / concept drawing
estimate the pole weight
consider the structural suitability of the mast for this application, including fatigue-related considerations if relevant
Project data provided by client:
Approximate mast height: 13.45 m
Horizontal force from wind turbine at 15 m: 4,900 N
Horizontal force on mast at 8 m: 3,000 N
Wind turbine weight: 320 kg
Material: steel S235 or S355
Surface treatment: hot-dip galvanizing
Application: outdoor use, wind turbine support mast
Manufacturing preference:
Our production is optimized for steel mast sections up to approximately 12 m in length.
For this reason, we are particularly interested in a polygonal steel mast solution, possibly in 2 sections, with an overlap / slip-joint connection if structurally suitable.
However, the engineer may also propose another technically and economically suitable mast configuration.
Important:
At this stage, we need a proposal / concept design only, not a fully detailed fabrication package.
Final manufacturing details can be finalized later.
Deliverables:
brief structural design basis
proposed mast arrangement
preliminary section sizing / dimensioning
concept / proposal drawing
estimated steel weight
notes / assumptions used for the design
Preferred experience:
steel pole / mast / monopole design
wind-loaded steel structures
structural calculations for custom poles
experience with segmented steel poles is a plus
experience with turbine support structures is a plus
To apply, please send:
short introduction
examples of similar projects you have worked on
proposed price
expected delivery time
software you will use for calculations / design read less
This is not a standard catalogue pole. The mast needs to be designed based on specific loading conditions provided by the client.
Project scope:
We need an engineer who can:
review the given loading conditions
calculate the required mast configuration
propose suitable mast diameter / section sizes / thicknesses
advise whether the mast should be 1-piece or 2-piece
prepare a proposal / concept drawing
estimate the pole weight
consider the structural suitability of the mast for this application, including fatigue-related considerations if relevant
Project data provided by client:
Approximate mast height: 13.45 m
Horizontal force from wind turbine at 15 m: 4,900 N
Horizontal force on mast at 8 m: 3,000 N
Wind turbine weight: 320 kg
Material: steel S235 or S355
Surface treatment: hot-dip galvanizing
Application: outdoor use, wind turbine support mast
Manufacturing preference:
Our production is optimized for steel mast sections up to approximately 12 m in length.
For this reason, we are particularly interested in a polygonal steel mast solution, possibly in 2 sections, with an overlap / slip-joint connection if structurally suitable.
However, the engineer may also propose another technically and economically suitable mast configuration.
Important:
At this stage, we need a proposal / concept design only, not a fully detailed fabrication package.
Final manufacturing details can be finalized later.
Deliverables:
brief structural design basis
proposed mast arrangement
preliminary section sizing / dimensioning
concept / proposal drawing
estimated steel weight
notes / assumptions used for the design
Preferred experience:
steel pole / mast / monopole design
wind-loaded steel structures
structural calculations for custom poles
experience with segmented steel poles is a plus
experience with turbine support structures is a plus
To apply, please send:
short introduction
examples of similar projects you have worked on
proposed price
expected delivery time
software you will use for calculations / design read less
We are looking for an experienced structural or mechanical engineer to support the design of a steel mast for a small wind turbine project.
This is not a standard catalogue pole. The mast needs to be designed based on specific loading conditions provided by the client.
Project scope:
We need an engineer who can:
review the given loading conditions
calculate the required mast configuration... read more
This is not a standard catalogue pole. The mast needs to be designed based on specific loading conditions provided by the client.
Project scope:
We need an engineer who can:
review the given loading conditions
calculate the required mast configuration... read more
We are looking for an experienced structural or mechanical engineer to support the design of a steel mast for a small wind turbine project.
This is not a standard catalogue pole. The mast needs to be designed based on specific loading conditions provided by the client.
Project scope:
We need an engineer who can:
review the given loading conditions
calculate the required mast configuration
propose suitable mast diameter / section sizes / thicknesses
advise whether the mast should be 1-piece or 2-piece
prepare a proposal / concept drawing
estimate the pole weight
consider the structural suitability of the mast for this application, including fatigue-related considerations if relevant
Project data provided by client:
Approximate mast height: 13.45 m
Horizontal force from wind turbine at 15 m: 4,900 N
Horizontal force on mast at 8 m: 3,000 N
Wind turbine weight: 320 kg
Material: steel S235 or S355
Surface treatment: hot-dip galvanizing
Application: outdoor use, wind turbine support mast
Manufacturing preference:
Our production is optimized for steel mast sections up to approximately 12 m in length.
For this reason, we are particularly interested in a polygonal steel mast solution, possibly in 2 sections, with an overlap / slip-joint connection if structurally suitable.
However, the engineer may also propose another technically and economically suitable mast configuration.
Important:
At this stage, we need a proposal / concept design only, not a fully detailed fabrication package.
Final manufacturing details can be finalized later.
Deliverables:
brief structural design basis
proposed mast arrangement
preliminary section sizing / dimensioning
concept / proposal drawing
estimated steel weight
notes / assumptions used for the design
Preferred experience:
steel pole / mast / monopole design
wind-loaded steel structures
structural calculations for custom poles
experience with segmented steel poles is a plus
experience with turbine support structures is a plus
To apply, please send:
short introduction
examples of similar projects you have worked on
proposed price
expected delivery time
software you will use for calculations / design read less
This is not a standard catalogue pole. The mast needs to be designed based on specific loading conditions provided by the client.
Project scope:
We need an engineer who can:
review the given loading conditions
calculate the required mast configuration
propose suitable mast diameter / section sizes / thicknesses
advise whether the mast should be 1-piece or 2-piece
prepare a proposal / concept drawing
estimate the pole weight
consider the structural suitability of the mast for this application, including fatigue-related considerations if relevant
Project data provided by client:
Approximate mast height: 13.45 m
Horizontal force from wind turbine at 15 m: 4,900 N
Horizontal force on mast at 8 m: 3,000 N
Wind turbine weight: 320 kg
Material: steel S235 or S355
Surface treatment: hot-dip galvanizing
Application: outdoor use, wind turbine support mast
Manufacturing preference:
Our production is optimized for steel mast sections up to approximately 12 m in length.
For this reason, we are particularly interested in a polygonal steel mast solution, possibly in 2 sections, with an overlap / slip-joint connection if structurally suitable.
However, the engineer may also propose another technically and economically suitable mast configuration.
Important:
At this stage, we need a proposal / concept design only, not a fully detailed fabrication package.
Final manufacturing details can be finalized later.
Deliverables:
brief structural design basis
proposed mast arrangement
preliminary section sizing / dimensioning
concept / proposal drawing
estimated steel weight
notes / assumptions used for the design
Preferred experience:
steel pole / mast / monopole design
wind-loaded steel structures
structural calculations for custom poles
experience with segmented steel poles is a plus
experience with turbine support structures is a plus
To apply, please send:
short introduction
examples of similar projects you have worked on
proposed price
expected delivery time
software you will use for calculations / design read less
Things to know
Expert
Skill Level
$10 - $25/hr
Hourly (USD)
Part-time
Job type
Under 1-month
Job duration
Areas of expertise
2D & 3D by Solidworks
2D CAD Drawings
2D and 3D CAD Design
2D and 3D Engineering Design
3D AutoCAD, Ansys
Bentley STAAD.Pro
CSi SAP2000
Steel Structure Design
Structural Analysis
+6 more
Job categories
Structural Steel Detailing
Mechanical Design Services
Mechanical Engineering
Structural Engineering
Steel Detailing Services
+2 more
About the client
Payment ready
Macedonia (03:59 am)
Posted
Active
Job activity
33 Applicants
0 interviews in progress
More open jobs from this client (1)
Urgent Steel Detailer / Workshop Drawing Engineer for Hall 1 Steel Substructure
Remote - Posted
We are looking for an experienced steel detailer / workshop drawing engineer for an urgent industrial steel project.
The assignment is for Hall 1 steel substructure worksho...
Structural Steel Detailing
Shop Drawing Services
Fabrication Drawings Services
Steel Detailing Services
Steel Shop Drawing Services
View job
Similar jobs
Cabana Plans - Complete Permit Plans (including engineering, Sign & Seal)
United States - Posted
We need complete permit plans (including engineering, and Sign & Seal) for a Cabana in California. Attached is the preliminary design. Required output plan set in PDF format a...
Construction Drawings
Design & Drafting
Architectural Drawing Services
Architectural Planning and Design
Structural Engineering
View job
To Model a single story Dry-stone timber laced masonry structure and analyze it for Push-Over Analysis in SAP2000
Remote - Posted
I am a final year Civil Engineering Student, and for our final year design project, we are need to model a single story Dry stone timber laced masonry building, and do analysi...
Structural Engineering
Structural Design Services
Civil Engineering
View job
Mechanical Design of a Transforming Mirror Cube Secret Box with Gear Mechanism
Remote - Posted
I am looking for a skilled Mechanical Engineer to design a 3D model for a "Mirror Cube" that transforms into a secret jewelry/ring box using an internal gear mechanism, exactl...
Mechanical Design Services
3D Modeling
3D Design Services
View job
Pallet Dispenser
Remote - Posted
We are ATM Lazić, a Serbian manufacturer of industrial packaging machinery with 30+ years of experience serving EU clients. We need a complete mechanical design package for an...
3D Modeling
3D Product Modeling
Manufacturing Drawings
Mechanical Engineering
Machine Design
View job
Designer needed for Stress Analysis and Support Load Calculation for Fire Pump Room Piping System
Remote - Posted
We are seeking a piping stress analysis designer/engineer to perform a detailed stress analysis and support load calculation for a fire pump room piping system based on the at...
Engineering Design
FEA Finite Element Analysis
Structural Engineering
Mechanical Engineering
View job
Mechanical design engineer for panel components development drawing
Remote - Posted
Experience in designing electrical panel components development drawing and converting to nesting drawing for lasar cutting
Mechanical Design Services
Design Engineering Services
Mechanical Drawing Services
View job
