Hire RF PCB design Designers in Brazil

I am an Electrical Engineer specializing in electronic hardware and PCB design, with a focus on RF, high-speed interfaces, signal integrity, embedded systems, and manufacturable electronic products.... Read more

I am an Electrical Engineer specializing in electronic hardware and PCB design, with a focus on RF, high-speed interfaces, signal integrity, embedded systems, and manufacturable electronic products. I support both complete hardware development and focused engineering work such as PCB design review, troubleshooting, electromagnetic simulation, signal-integrity analysis, layout optimization, and preparation for manufacturing. My work covers the complete hardware development cycle, including system architecture, component selection, schematic capture, multilayer PCB layout, power architecture, prototype bring-up, debugging, validation, DFM/DFT, and manufacturing release. A recent project involved the electromagnetic analysis and optimization of a GMSL2 serializer-to-FAKRA PCB interconnect operating up to 6 GHz. I developed a KiCad-to-openEMS simulation workflow to evaluate S-parameters, return loss, impedance, transmission-line geometry, connector launches, via structures, anti-pads, and reference-plane discontinuities. I also develop embedded and industrial hardware using STM32 and ESP32 platforms, cellular connectivity, GNSS, LoRaWAN, CAN, RS-485, Ethernet, BLE, Wi-Fi, sensors, industrial interfaces, low-power electronics, and battery-powered systems. Typical projects I support include: — Complete schematic and PCB development — RF and high-speed PCB design — Multilayer and controlled-impedance layouts — PCB design review before fabrication — Existing hardware troubleshooting and redesign — Signal-integrity and electromagnetic analysis — Embedded and industrial IoT hardware — Power-management circuits — Prototype bring-up and validation — BOM optimization and component selection — DFM, DFT and manufacturing documentation I have experience across industrial R&D, freelance engineering, hardware validation, and test engineering, including two years in R&D at Furukawa Electric. My main engineering tools include KiCad, Altium Designer, openEMS, Python, EasyEDA Pro, and ParaView. I also maintain my own electronics bench with an oscilloscope, spectrum analyzer, soldering equipment, and rework tools for prototype assembly, bring-up, troubleshooting, and validation. My objective is not simply to complete a PCB layout, but to deliver hardware that is electrically robust, manufacturable, testable, and ready for the next stage of product development. If you have a new hardware design, a PCB approaching fabrication, or an existing board that is not performing as expected, I can review the requirements and recommend the most effective path forward.

I am an Electrical Engineer specializing in electronic hardware and PCB design, with a focus on RF, high-speed interfaces, signal integrity, embedded systems, and manufacturable electronic products.... Read more

I am an Electrical Engineer specializing in electronic hardware and PCB design, with a focus on RF, high-speed interfaces, signal integrity, embedded systems, and manufacturable electronic products. I support both complete hardware development and focused engineering work such as PCB design review, troubleshooting, electromagnetic simulation, signal-integrity analysis, layout optimization, and preparation for manufacturing. My work covers the complete hardware development cycle, including system architecture, component selection, schematic capture, multilayer PCB layout, power architecture, prototype bring-up, debugging, validation, DFM/DFT, and manufacturing release. A recent project involved the electromagnetic analysis and optimization of a GMSL2 serializer-to-FAKRA PCB interconnect operating up to 6 GHz. I developed a KiCad-to-openEMS simulation workflow to evaluate S-parameters, return loss, impedance, transmission-line geometry, connector launches, via structures, anti-pads, and reference-plane discontinuities. I also develop embedded and industrial hardware using STM32 and ESP32 platforms, cellular connectivity, GNSS, LoRaWAN, CAN, RS-485, Ethernet, BLE, Wi-Fi, sensors, industrial interfaces, low-power electronics, and battery-powered systems. Typical projects I support include: — Complete schematic and PCB development — RF and high-speed PCB design — Multilayer and controlled-impedance layouts — PCB design review before fabrication — Existing hardware troubleshooting and redesign — Signal-integrity and electromagnetic analysis — Embedded and industrial IoT hardware — Power-management circuits — Prototype bring-up and validation — BOM optimization and component selection — DFM, DFT and manufacturing documentation I have experience across industrial R&D, freelance engineering, hardware validation, and test engineering, including two years in R&D at Furukawa Electric. My main engineering tools include KiCad, Altium Designer, openEMS, Python, EasyEDA Pro, and ParaView. I also maintain my own electronics bench with an oscilloscope, spectrum analyzer, soldering equipment, and rework tools for prototype assembly, bring-up, troubleshooting, and validation. My objective is not simply to complete a PCB layout, but to deliver hardware that is electrically robust, manufacturable, testable, and ready for the next stage of product development. If you have a new hardware design, a PCB approaching fabrication, or an existing board that is not performing as expected, I can review the requirements and recommend the most effective path forward.

Thank you for visiting my profile. I'm Engr. Muhammad Uzair, a hardware and firmware engineer with 6+ years of experience delivering production-ready electronic solutions. I specialize in: - Multil... Read more

Thank you for visiting my profile. I'm Engr. Muhammad Uzair, a hardware and firmware engineer with 6+ years of experience delivering production-ready electronic solutions. I specialize in: - Multilayer PCB design (up to 8 layers) — signal integrity, RF, IoT, and power electronics - Power electronics design — DC-DC and AC-DC conversion circuits - Firmware development for STM32, dsPIC, ESP32/ESP8266 with UART, SPI, I2C, CAN, USB, and MODBUS - RF circuit design — filters, antenna tuning, and wireless systems From schematic capture to Gerber files and working prototype — I manage the full design cycle with precision and on-time delivery. Let's bring your ideas to life!