Ultrasonic Transducer AFE / Pulser-Receiver Electronics Development Ended

About the job

Objective: The goal is to design and develop functional prototype AFE(Analog Front End)/pulser-receiver system that can directly interface with any raw underwater transducer (200KHz to 1MHz) and deliver full echo-profile data to a Raspberry Pi.

Description: I am looking for an experienced analog electronics / ultrasonic / sonar engineer to design and develop (physical device) a custom electronics board (AFE) to interface with a raw underwater ultrasonic transducer.
The board will interface directly with a raw piezoelectric ultrasonic transducer and provide the complete transmit and receive signal chain required for underwater sonar.

The basic architecture is:
Raw Ultrasonic Transducer ↔ TX/RX Front End ↔ ADC ↔ Raspberry Pi / Processor
Required Electronics

The AFE should include:

1. Transducer interface
2. Transmit / Pulser
3. Transmit/Receive switching
4. Receive Analog Front End
5. ADC / Data Acquisition
6. Digital interface
7. Trigger / timing

Desired Output: For each transmitted ping, I want to obtain data similar to:
Amplitude / signal strength vs. time or range (Full Echo Profile output).

I need the complete Altium source files in addition to the Gerber files. Please provide the schematic source, PCB source/layout, Gerbers, BOM, pick-and-place files if applicable, and all design documentation. The PCB should be designed specifically for a ~500 kHz underwater piezoelectric transducer and must include the TX pulser, T/R protection/switching, low... read more
Objective: The goal is to design and develop functional prototype AFE(Analog Front End)/pulser-receiver system that can directly interface with any raw underwater transducer (200KHz to 1MHz) and deliver full echo-profile data to a Raspberry Pi.

Description: I am looking for an experienced analog electronics / ultrasonic / sonar engineer to design and develop (physical device) a custom electronics board (AFE) to interface with a raw underwater ultrasonic transducer.
The board will interface directly with a raw piezoelectric ultrasonic transducer and provide the complete transmit and receive signal chain required for underwater sonar.

The basic architecture is:
Raw Ultrasonic Transducer ↔ TX/RX Front End ↔ ADC ↔ Raspberry Pi / Processor
Required Electronics

The AFE should include:

1. Transducer interface
2. Transmit / Pulser
3. Transmit/Receive switching
4. Receive Analog Front End
5. ADC / Data Acquisition
6. Digital interface
7. Trigger / timing

Desired Output: For each transmitted ping, I want to obtain data similar to:
Amplitude / signal strength vs. time or range (Full Echo Profile output).

I need the complete Altium source files in addition to the Gerber files. Please provide the schematic source, PCB source/layout, Gerbers, BOM, pick-and-place files if applicable, and all design documentation. The PCB should be designed specifically for a ~500 kHz underwater piezoelectric transducer and must include the TX pulser, T/R protection/switching, low-noise receive AFE, filtering, ADC, timing/triggering, and interface to a Raspberry Pi for full echo-profile acquisition. I also need an assembled and tested prototype, not just manufacturing files. read less
Objective: The goal is to design and develop functional prototype AFE(Analog Front End)/pulser-receiver system that can directly interface with any raw underwater transducer (200KHz to 1MHz) and deliver full echo-profile data to a Raspberry Pi.

Description: I am looking for an experienced analog electronics / ultrasonic / sonar engineer to design and develop (physical device) a custom electroni... read more
Objective: The goal is to design and develop functional prototype AFE(Analog Front End)/pulser-receiver system that can directly interface with any raw underwater transducer (200KHz to 1MHz) and deliver full echo-profile data to a Raspberry Pi.

Description: I am looking for an experienced analog electronics / ultrasonic / sonar engineer to design and develop (physical device) a custom electronics board (AFE) to interface with a raw underwater ultrasonic transducer.
The board will interface directly with a raw piezoelectric ultrasonic transducer and provide the complete transmit and receive signal chain required for underwater sonar.

The basic architecture is:
Raw Ultrasonic Transducer ↔ TX/RX Front End ↔ ADC ↔ Raspberry Pi / Processor
Required Electronics

The AFE should include:

1. Transducer interface
2. Transmit / Pulser
3. Transmit/Receive switching
4. Receive Analog Front End
5. ADC / Data Acquisition
6. Digital interface
7. Trigger / timing

Desired Output: For each transmitted ping, I want to obtain data similar to:
Amplitude / signal strength vs. time or range (Full Echo Profile output).

I need the complete Altium source files in addition to the Gerber files. Please provide the schematic source, PCB source/layout, Gerbers, BOM, pick-and-place files if applicable, and all design documentation. The PCB should be designed specifically for a ~500 kHz underwater piezoelectric transducer and must include the TX pulser, T/R protection/switching, low-noise receive AFE, filtering, ADC, timing/triggering, and interface to a Raspberry Pi for full echo-profile acquisition. I also need an assembled and tested prototype, not just manufacturing files. read less

Things to know

Job location

Remote

Work location

Job skill level

Expert

Skill Level

Job rate

$500

Fixed-rate (USD)

Job type

Part-time

Job type

Job length

Under 1-month

Job duration

Areas of expertise

3D PCB Modeling Altium Analog Electronics Design Arduino Schematic Design +2 more

Job categories

Electronic Prototyping and Design Services 3D Design Services 3D Modeling

About the client

Payment ready

United States (02:26 am)

Posted

Active

Job activity

12 Applicants

1 interviews in progress

More open jobs from this client (4)

PCB testing and firmware development for acoustic transducer

Remote - Posted
THIS PROJECT HAS TWO PARTS *. Existing PCB Verification, Testing & Validation *. Developing firmware for the burst generation & echo processing Existing PCB Verification,...
Electronic Prototyping and Design Services PCB Design Services Firmware Developers
View job

Underwater Enclosure for Scanning Echo Sounder

India - Posted
Underwater Ultrasonic Mechanical Scanning Device ------------------------------------------------- We are seeking an expert to design and develop an underwater FORWARD LOOKI...
Mechanical Design Services CAD Drawing Services SolidWorks Design Services
View job

Ultrasonic Transducer AFE / Pulser-Receiver Electronics Development

Remote - Posted
NOTE: Looking for a professional to handle the below project in "Hyderabad City, TELANGANA STATE, INDIA". Objective: The goal is to design and develop functional prototype...
Electrical Engineering Engineering Design Electronics Design Service
View job

Underwater Scanning Sonar - LOCAL ONLY (Connecticut)

Remote - Posted
I'm seeking an experienced local freelancer (in state of Connecticut) to help mount an underwater sensor on a stepper motor for 180-degree scanning capabilities. The sensor wi...
Engineering Design 3D Design Services 3D Modeling
View job

Similar jobs

Need a Dynamo script for QTO/Schedules in Civil 3D.

Remote - Posted
Job Requirement / Scope of Work Civil 3D / Dynamo Programmer – Automated QTO Extraction and Reporting Tool Develop a Dynamo script for Autodesk Civil 3D that automates t...
Civil Drafting Services 3D Design Services 3D Modeling
View job

CAD designer needed to model 3D consumer product

Remote - Posted
Need to design South Indian style closed stone setting necklace,jhumka,bangles. Stone measurements and drawing will be provided.
3D Modeling 3D Design Services Engineering Design
View job

SCAN TO 3D SOLIDWORKS DESIGNER

Remote - Posted
Have scans to be imported into SolidWorks for design editing
3D Scan to CAD Service 3D CAD Translation Services 3D Design Services
View job

SolidWorks 2026 FEA Analysis

Remote - Posted
SOLIDWORKS 2026 FEA simulation analysis needed on bolted structural assembly model. Model is complete less fasteners. This is a project to project need. Turnaround is A.S.A....
FEA Finite Element Analysis 3D Design Services 3D Modeling
View job

Multi-Axis CNC Programming - SolidCAM Preferred

United States - Posted
Looking for a candidate that could work on-site in Bethlehem, PA and help transform cutting edge designs into programs for multi-axis milling applications. Team member could i...
CNC Programming SolidWorks Design Services 3D Design Services
View job

Technical concept illustration — subscale composite launch vehicle interstage test article

Remote - Posted
We need a single illustrative image (not a diagram) for a research funding submission, to be used publicly in web articles. Minimum 1920×1080px, 16:9 aspect ratio. Subject:...
Concept Design 3D Rendering Services 3D Modeling Aerospace Engineering
View job

How it works

Find hourly jobs

Find hourly jobs

Top rated experts are regularly hired for hourly jobs & ongoing client work.
Fixed-rate jobs

Fixed-rate jobs

Experts can browse & apply to fixed-rate work & quote on a flat-rate basis.
Design contests

Design contests

Experts build a reputation and earn prizes by participating in design challenges.

About Cad Crowd

4.9/5.0

(Our client satisfaction)

G2 2022

Spring high performer

222,193

global members

33,595

projects delivered to clients


Trusted by
US Army Corps of Engineers
Tiffany
BCG
Target
KPMG
Xprize

Find freelance & remote jobs

Your next big opportunity is just a click away. Create a free profile and start finding work tailored to your skills.