Ultrasonic Transducer AFE / Pulser-Receiver Electronics Development Ended

About the job

NOTE: Looking for a professional to handle the below project in "Hyderabad City, TELANGANA STATE, INDIA".

Objective: The goal is to design and develop functional prototype AFE(Analog Front End)/pulser-receiver system that can directly interface with any raw underwater transducer (200KHz to 1MHz) and deliver full echo-profile data to a Raspberry Pi.

Description: I am looking for an experienced analog electronics / ultrasonic / sonar engineer to design and develop (physical device) a custom electronics board (AFE) to interface with a raw underwater ultrasonic transducer.
The board will interface directly with a raw piezoelectric ultrasonic transducer and provide the complete transmit and receive signal chain. The transducer we are using is:
https://ultrans.en.made-in-china.com/product/yxYUzZhJhOpW/China-500kHz-Ultrasonic-Underwater-Acoustic-Transducer-Ranging-Transducer-Fishfinder-Transducers-Chirp-Transducers-Transducers-FYW-500-20B-for-Positioning.html

The basic architecture is:
Piezoelectric Ultrasonic Transducer ↔ TX/RX Front End ↔ ADC ↔ Raspberry Pi / Processor
Required Electronics

The AFE should include:

1. Transducer interface
2. Transmit / Pulser
3. Transmit/Receive switching
4. Receive Analog Front End
5. ADC / Data Acquisition
6. Digital interface
7. Trigger / timing

Desired Output: For each transmitted ping, I want to obtain data similar to:
Amplitude / signal strength vs. time or range (Full Echo Profile output).

I need the complete A... read more
NOTE: Looking for a professional to handle the below project in "Hyderabad City, TELANGANA STATE, INDIA".

Objective: The goal is to design and develop functional prototype AFE(Analog Front End)/pulser-receiver system that can directly interface with any raw underwater transducer (200KHz to 1MHz) and deliver full echo-profile data to a Raspberry Pi.

Description: I am looking for an experienced analog electronics / ultrasonic / sonar engineer to design and develop (physical device) a custom electronics board (AFE) to interface with a raw underwater ultrasonic transducer.
The board will interface directly with a raw piezoelectric ultrasonic transducer and provide the complete transmit and receive signal chain. The transducer we are using is:
https://ultrans.en.made-in-china.com/product/yxYUzZhJhOpW/China-500kHz-Ultrasonic-Underwater-Acoustic-Transducer-Ranging-Transducer-Fishfinder-Transducers-Chirp-Transducers-Transducers-FYW-500-20B-for-Positioning.html

The basic architecture is:
Piezoelectric Ultrasonic Transducer ↔ TX/RX Front End ↔ ADC ↔ Raspberry Pi / Processor
Required Electronics

The AFE should include:

1. Transducer interface
2. Transmit / Pulser
3. Transmit/Receive switching
4. Receive Analog Front End
5. ADC / Data Acquisition
6. Digital interface
7. Trigger / timing

Desired Output: For each transmitted ping, I want to obtain data similar to:
Amplitude / signal strength vs. time or range (Full Echo Profile output).

I need the complete Altium source files in addition to the Gerber files. Please provide the schematic source, PCB source/layout, Gerbers, BOM, pick-and-place files if applicable, and all design documentation. The PCB should be designed specifically for a ~500 kHz underwater piezoelectric transducer and must include the TX pulser, T/R protection/switching, low-noise receive AFE, filtering, ADC, timing/triggering, and interface to a Raspberry Pi for full echo-profile acquisition. I also need an assembled and tested prototype, not just manufacturing files.


The freelancer will provide the following items:

Gerber ZIP
NC drill files
Final BOM with manufacturer part numbers
Pick-and-place/centroid file
Assembly drawing
Schematic PDF
PCB layout PDF
PCB source files (KiCad/Altium/etc.)
3D STEP model
Fabrication/assembly notes
DFM/DRC/ERC reports
Firmware/programming requirements read less
NOTE: Looking for a professional to handle the below project in "Hyderabad City, TELANGANA STATE, INDIA".

Objective: The goal is to design and develop functional prototype AFE(Analog Front End)/pulser-receiver system that can directly interface with any raw underwater transducer (200KHz to 1MHz) and deliver full echo-profile data to a Raspberry Pi.

Description: I am looking for an experience... read more
NOTE: Looking for a professional to handle the below project in "Hyderabad City, TELANGANA STATE, INDIA".

Objective: The goal is to design and develop functional prototype AFE(Analog Front End)/pulser-receiver system that can directly interface with any raw underwater transducer (200KHz to 1MHz) and deliver full echo-profile data to a Raspberry Pi.

Description: I am looking for an experienced analog electronics / ultrasonic / sonar engineer to design and develop (physical device) a custom electronics board (AFE) to interface with a raw underwater ultrasonic transducer.
The board will interface directly with a raw piezoelectric ultrasonic transducer and provide the complete transmit and receive signal chain. The transducer we are using is:
https://ultrans.en.made-in-china.com/product/yxYUzZhJhOpW/China-500kHz-Ultrasonic-Underwater-Acoustic-Transducer-Ranging-Transducer-Fishfinder-Transducers-Chirp-Transducers-Transducers-FYW-500-20B-for-Positioning.html

The basic architecture is:
Piezoelectric Ultrasonic Transducer ↔ TX/RX Front End ↔ ADC ↔ Raspberry Pi / Processor
Required Electronics

The AFE should include:

1. Transducer interface
2. Transmit / Pulser
3. Transmit/Receive switching
4. Receive Analog Front End
5. ADC / Data Acquisition
6. Digital interface
7. Trigger / timing

Desired Output: For each transmitted ping, I want to obtain data similar to:
Amplitude / signal strength vs. time or range (Full Echo Profile output).

I need the complete Altium source files in addition to the Gerber files. Please provide the schematic source, PCB source/layout, Gerbers, BOM, pick-and-place files if applicable, and all design documentation. The PCB should be designed specifically for a ~500 kHz underwater piezoelectric transducer and must include the TX pulser, T/R protection/switching, low-noise receive AFE, filtering, ADC, timing/triggering, and interface to a Raspberry Pi for full echo-profile acquisition. I also need an assembled and tested prototype, not just manufacturing files.


The freelancer will provide the following items:

Gerber ZIP
NC drill files
Final BOM with manufacturer part numbers
Pick-and-place/centroid file
Assembly drawing
Schematic PDF
PCB layout PDF
PCB source files (KiCad/Altium/etc.)
3D STEP model
Fabrication/assembly notes
DFM/DRC/ERC reports
Firmware/programming requirements read less

Things to know

Job location

Remote

Work location

Job skill level

Expert

Skill Level

Job rate

$800

Fixed-rate (USD)

Job type

Part-time

Job type

Job length

Under 1-month

Job duration

Areas of expertise

Altium Altium Designer Analog Electronics Design BOM (Bill of Materials) Electronic Hardware Design Embedded Systems +3 more

Job categories

Electrical Engineering Engineering Design Electronics Design Service

About the client

Payment ready

United States (02:26 am)

Posted

Active

Job activity

14 Applicants

1 interviews in progress

More open jobs from this client (4)

PCB testing and firmware development for acoustic transducer

Remote - Posted
THIS PROJECT HAS TWO PARTS *. Existing PCB Verification, Testing & Validation *. Developing firmware for the burst generation & echo processing Existing PCB Verification,...
Electronic Prototyping and Design Services PCB Design Services Firmware Developers
View job

Underwater Enclosure for Scanning Echo Sounder

India - Posted
Underwater Ultrasonic Mechanical Scanning Device ------------------------------------------------- We are seeking an expert to design and develop an underwater FORWARD LOOKI...
Mechanical Design Services CAD Drawing Services SolidWorks Design Services
View job

Ultrasonic Transducer AFE / Pulser-Receiver Electronics Development

Remote - Posted
Objective: The goal is to design and develop functional prototype AFE(Analog Front End)/pulser-receiver system that can directly interface with any raw underwater transducer (...
Electronic Prototyping and Design Services 3D Design Services 3D Modeling
View job

Underwater Scanning Sonar - LOCAL ONLY (Connecticut)

Remote - Posted
I'm seeking an experienced local freelancer (in state of Connecticut) to help mount an underwater sensor on a stepper motor for 180-degree scanning capabilities. The sensor wi...
Engineering Design 3D Design Services 3D Modeling
View job

Similar jobs

CAD designer needed to model 3D consumer product

Remote - Posted
Need to design South Indian style closed stone setting necklace,jhumka,bangles. Stone measurements and drawing will be provided.
3D Modeling 3D Design Services Engineering Design
View job

CAD Designer Needed – Custom Wallet Chain Clip Design

Remote - Posted
Hi there, My name is Salvador, and my business partner and I are looking for a CAD designer to assist us with an existing wallet-chain project. We have the entire wallet...
3D Design Services 3D Modeling Engineering Design
View job

Designing a Mechanical Medical Device

Remote - Posted
We are a IITGN Based Startup and need industrial design Experts to design out product for a commercial use purpose.
Mechanical CAD Design Medical Devices Design Product Engineering Services Mechanical Design Services Engineering Design
View job

Mechanical engineering designer

Visakhapatnam, India - Posted
Desiging support for Product development with familiar with solidworks / creo to create 3d models and generate required views.
Mechanical Design Services Machine Design Engineering Design
View job

PV*SOL Design & Simulation Expert Needed for Commercial Solar/BESS Project (700 kWp / 500 kWh)

Remote - Posted
Project Overview: PV Array: ~700 kWp rooftop installation Inverter System: 500 kW capacity (commercial string inverters) Battery Storage: 500 kWh BESS integration Grid S...
Solar Panel Drawing Plans Engineering Design Electrical Engineering PV Solar Panel Drafting
View job

Pressure Vessels Mechanical Draftsman

Remote - Posted
I am looking for a Mechanical Static Equipment Draftsman that has experience in oil & gas international projects to create detail drawings for pressure vessels the candida...
Mechanical Drafting Engineering Design 2D CAD Design Services Oil & Gas Mechanical Drawing Services
View job

How it works

Find hourly jobs

Find hourly jobs

Top rated experts are regularly hired for hourly jobs & ongoing client work.
Fixed-rate jobs

Fixed-rate jobs

Experts can browse & apply to fixed-rate work & quote on a flat-rate basis.
Design contests

Design contests

Experts build a reputation and earn prizes by participating in design challenges.

About Cad Crowd

4.9/5.0

(Our client satisfaction)

G2 2022

Spring high performer

222,193

global members

33,595

projects delivered to clients


Trusted by
US Army Corps of Engineers
Tiffany
BCG
Target
KPMG
Xprize

Find freelance & remote jobs

Your next big opportunity is just a click away. Create a free profile and start finding work tailored to your skills.