Full System DFM: Design & FEA for a Modular, Crimpable Spearpoint Ended

About the job

I am looking for a high-level DFM/FEA engineer to design a single, new flagship component for a high-performance spear system. You must be an expert in Fusion 360.
​The Goal:
Design a new "Spearpoint Ferrule" (v2.0) that combines all our innovations. This one component must do everything:
​Be the Spearpoint: It will hold modular "5mm barb inserts."
​Be Crimpable: It will attach directly to the bamboo shaft via a low-power, hand-powered circular crimper.
​Your Engineering & Design Tasks (All in Fusion 360):
​Thread Standard (Analysis):
​Analyze our "5mm barb" concept and recommend the strongest, most appropriate thread standard that can be integrated into its base.
​Design the new ferrule to accept these threads.
​Crimp Design (DFM):
​Design the base of the ferrule to be crimpable by a low-power press.
​This includes redesigning "flutes" and features that "bite" into the bamboo shaft.
​"Flush-Finish" Aesthetics (DFM):
​Design the base of the ferrule with a "tapered skirt" engineered to compress perfectly flush with the bamboo shaft after crimping.
​Aesthetics (General):
​The body of the ferrule should be "fluted" for a high-end, aesthetic finish.
​Deliverables:
​Your final delivery must be made by sharing the completed project with our Fusion 360 account.
​Fusion 360 Source Files (.f3d):
​The native, editable .f3d file for the new Gidgie_Spearpoint_v2.0.
​The native, editable .f3d file for the new Barb_5mm_Threaded.
​FEA Simulation Setups (in Fusion 360):... read more
I am looking for a high-level DFM/FEA engineer to design a single, new flagship component for a high-performance spear system. You must be an expert in Fusion 360.
​The Goal:
Design a new "Spearpoint Ferrule" (v2.0) that combines all our innovations. This one component must do everything:
​Be the Spearpoint: It will hold modular "5mm barb inserts."
​Be Crimpable: It will attach directly to the bamboo shaft via a low-power, hand-powered circular crimper.
​Your Engineering & Design Tasks (All in Fusion 360):
​Thread Standard (Analysis):
​Analyze our "5mm barb" concept and recommend the strongest, most appropriate thread standard that can be integrated into its base.
​Design the new ferrule to accept these threads.
​Crimp Design (DFM):
​Design the base of the ferrule to be crimpable by a low-power press.
​This includes redesigning "flutes" and features that "bite" into the bamboo shaft.
​"Flush-Finish" Aesthetics (DFM):
​Design the base of the ferrule with a "tapered skirt" engineered to compress perfectly flush with the bamboo shaft after crimping.
​Aesthetics (General):
​The body of the ferrule should be "fluted" for a high-end, aesthetic finish.
​Deliverables:
​Your final delivery must be made by sharing the completed project with our Fusion 360 account.
​Fusion 360 Source Files (.f3d):
​The native, editable .f3d file for the new Gidgie_Spearpoint_v2.0.
​The native, editable .f3d file for the new Barb_5mm_Threaded.
​FEA Simulation Setups (in Fusion 360):
​The FEA setup and results for the barb pull-out test must be saved in the "Simulation" workspace of the .f3d file.
​The FEA setup and results for the crimping simulation must also be saved within the project.
​1-Page Recommendation:
​A brief PDF (attached to the Fusion 360 project) justifying your chosen thread standard.
Successful completion of this job will trigger another 13 parts. read less
I am looking for a high-level DFM/FEA engineer to design a single, new flagship component for a high-performance spear system. You must be an expert in Fusion 360.
​The Goal:
Design a new "Spearpoint Ferrule" (v2.0) that combines all our innovations. This one component must do everything:
​Be the Spearpoint: It will hold modular "5mm barb inserts."
​Be Crimpable: It will attach directly to the... read more
I am looking for a high-level DFM/FEA engineer to design a single, new flagship component for a high-performance spear system. You must be an expert in Fusion 360.
​The Goal:
Design a new "Spearpoint Ferrule" (v2.0) that combines all our innovations. This one component must do everything:
​Be the Spearpoint: It will hold modular "5mm barb inserts."
​Be Crimpable: It will attach directly to the bamboo shaft via a low-power, hand-powered circular crimper.
​Your Engineering & Design Tasks (All in Fusion 360):
​Thread Standard (Analysis):
​Analyze our "5mm barb" concept and recommend the strongest, most appropriate thread standard that can be integrated into its base.
​Design the new ferrule to accept these threads.
​Crimp Design (DFM):
​Design the base of the ferrule to be crimpable by a low-power press.
​This includes redesigning "flutes" and features that "bite" into the bamboo shaft.
​"Flush-Finish" Aesthetics (DFM):
​Design the base of the ferrule with a "tapered skirt" engineered to compress perfectly flush with the bamboo shaft after crimping.
​Aesthetics (General):
​The body of the ferrule should be "fluted" for a high-end, aesthetic finish.
​Deliverables:
​Your final delivery must be made by sharing the completed project with our Fusion 360 account.
​Fusion 360 Source Files (.f3d):
​The native, editable .f3d file for the new Gidgie_Spearpoint_v2.0.
​The native, editable .f3d file for the new Barb_5mm_Threaded.
​FEA Simulation Setups (in Fusion 360):
​The FEA setup and results for the barb pull-out test must be saved in the "Simulation" workspace of the .f3d file.
​The FEA setup and results for the crimping simulation must also be saved within the project.
​1-Page Recommendation:
​A brief PDF (attached to the Fusion 360 project) justifying your chosen thread standard.
Successful completion of this job will trigger another 13 parts. read less

Things to know

Job location

Bangkok, Thailand

Work location

Job skill level

Expert

Skill Level

Job rate

$200

Fixed-rate (USD)

Job type

Part-time

Job type

Job length

Under 1-month

Job duration

Areas of expertise

Autocad Fusion 360 CAD Modeling

Job categories

Design for Manufacturability (DFM Services) Mechanical Design Services FEA Finite Element Analysis Design Engineering Services +1 more

About the client

Payment ready

Australia (12:11 am)

Posted

Active

Job activity

8 Applicants

4 interviews in progress

6 unanswered invites

Similar jobs

Industrial design

Remote - Posted
Hello, my name is Shriyansh. We are manufacturers of construction materials with an existing facility spanning over 190,000 sq. ft. We are currently expanding into aggregate p...
AutoCAD Drafting & Design Industrial Design Services Product Engineering Services 3D Design Services Mechanical Design Services
View job

Mechanical Design Engineer – Collapsible / Deployable Consumer Product (Feasibility & Concept Development)

Remote - Posted
Project type: Mechanical engineering, mechanism design, feasibility assessment and prototyping Project description I am the founder of an early-stage consumer product st...
Mechanical Design Services Product Engineering Services Engineering Design
View job

Prototype Exercise Equipment Blueprint/CAD Program and Questions

Mckinney, United States - Posted
Hello, I'm looking for someone to help me come up with the design of a protype for a piece of workout equipment. I put and ai image of roughly what I'm looking for (will discu...
Exercise Equipment Design Product Engineering Services Mechanical Design Services Prototype Design Services
View job

Oscillating power tool saw blade

Remote - Posted
I am looking to produce a prototype of a steel saw blade. The material will need to be thin sheet metal, laser cut to very specific geometry + metal bending. I need help modif...
Sheet Metal Design Prototype Design Services Mechanical Design Services
View job

RTM Simulation Using Moldex3D

Remote - Posted
Part 1 Using Moldex 3D, simulate the Resin Transfer Molding (RTM) process for the prepared solid mesh and ply orientation (attached mfe and kpt files). Review the instructi...
3D Modeling Engineering Design Mechanical Design Services Product Engineering Services Mold and Die Design Services
View job

Hydrolic piston

Canada - Posted
Looking for experienced design engineer for quote looking for patent also and to assume functionality
3D Modeling Part-to-CAD Modeling Mechanical Design Services Machine Design Mechanical Engineering
View job

How it works

Find hourly jobs

Find hourly jobs

Top rated experts are regularly hired for hourly jobs & ongoing client work.
Fixed-rate jobs

Fixed-rate jobs

Experts can browse & apply to fixed-rate work & quote on a flat-rate basis.
Design contests

Design contests

Experts build a reputation and earn prizes by participating in design challenges.

About Cad Crowd

4.9/5.0

(Our client satisfaction)

G2 2022

Spring high performer

224,206

global members

33,595

projects delivered to clients


Trusted by
US Army Corps of Engineers
Tiffany
BCG
Target
KPMG
Xprize

Find freelance & remote jobs

Your next big opportunity is just a click away. Create a free profile and start finding work tailored to your skills.