Design of 3d photography studio

Contest Ended, Winner(s) have been selected.
Description:
Design a small 1.5 m x 1.5 m booth that will be an "add on" to the back of our current photography studios. These studios are in the middle of shopping centres. Single profile only. We have a specific design in mind so if your are good at CAD you won't have a problem doing this with ease
Wants:
Someone with experience in designing 3d CAD especially with experience in retail store design.
Don't Wants:
Someone who cannot show me they have completed similar work to a high standard
Ask for Sample:
Samples of previous work is fine
Software:
  1. Whatever you use

Entries

Discussion

Thu, 27 Mar 2014 13:53:11 +0000
This topic was covered by two previous challenges. In no case the wanna be photographer decided to move along with the design. If you find any design that pleases you, get in contact with the creator. Best regards

Lucian

Administrator

Wed, 26 Mar 2014 07:27:55 +0000
Hi Brendan,

Please remember to include attachments so the designers will fully understand your project. If you need help including these, please refer to this link http://goo.gl/mnFSgg and our help pages.

Thanks,
Lucian

Similar Contests on Cad Crowd

Cottage Lake House Porch Addition
We have a lovely cottage lakehouse that is lacking a covered back porch. The house appears very flat and it needs character. We will only cover the back from windows 1 to 3 to include the glass door. The remaining two windows to the left will not be covered. The porch should extend the length of the deck and follow the line of the deck as it is right on the property line. We can either go through the planters or move them if we need to. The planters allow for a set back of 22 to 24 inches to allow for a proper eave. I have a contractor that can build from sight or plans. Must have metal roof. I will attach a few photos of porches that I like to the last two spots.
Motion sensor
This project is to design the housing for a motion detector for commercial office buildings. it should be approximately 2.5-3.0 inch circle and the body should be no more than 1.0 inch thick. the circle can be bigger if the edges sweep out to with a nice curve back to the ceiling surface. it will mount to a standard t-bar ceiling grid. (the kind of ceiling with the drop in tiles) it should mount in the corner of a light fixture with a portion of the "top" or up facing side exposed to the light fixture. and have a window on the top that looks up at the light... (for a light sensor) the window shall be rectangle and dimensions are: 33.0×10.8mm. the face which points to the room shall have a PIR lens (like this one http://www.jvs.de/Carclo_Fresnel/Drawings/PF68_12076_Drawing.pdf i'd like to receive drawings that are 3d printer ready. ease of mass production and tooling should be considered. drawings should also be open for editing by our team. Our team will add the holders, screws, clips, etc for the Electronics inside. the mounting method could be a small piece of spring steel or plastic. White plastic/PC examples: http://cdn3.volusion.com/jn7vt.cfos2/v/vspfiles/photos/HBL3-2.jpg?1416706843
3D design for a lovely four-leafs clover keyholder
I am looking for a model of a four-leafs clover key holder that would just make me and anyone else fall in love with. If selected it would be an exclusive design. I just need the design of the clover (not the keyring, chain, etc.). I have something very specific in mind. Of course, should be so that it can be realistically produced (technical characteristic of the design - not necessarily the file/program yet). I am looking for something kind of full body, rounded shapes, if leafs kind of remind of a hearth even better, but not main. It really just should look: that's the one. I am attaching a pic of similar objects, just to give you a sense of the full body, roundness ...
Hinge for mailbox
We are designing a thick gauge aluminum mailbox (0.080” aluminum (2024 or similar) front and back; ¼” (6061 or similar) lid). We are having problems finding an off-the-shelf hinge for the lid that meets our evaluation criteria (below). Lid is a thick, flat piece of aluminum, no bends. Final product will be powder-coated.
Solidworks Car model
I am looking for someone to model in solidworks a replica of a car already on the market. I like super cars and classic cars! The file needs to be somewhat editable in solidworks and renderable in keyshot. The contest is quite open ended, the more detail the better.