Iphone Case - Freelance 3D Designer & Modelling Contest

in 3D Modeling Design held by ShadiB
Contest Ended, Winner(s) have been selected.
  • Open
  • Choosing Finalist
  • Ended
Description:
This is an Iphone 5 case. It is made out of injection molded rubber on the inside and titanium on the outside shell. As you can see in the attached files, the center back of the case is composed of 2 pieces: a round injection molded rubber piece and an aluminum sheet shaped as an eclipse. This aluminum sheet is engraved on one side with an s shape, a wire will be laid on top of that piece.

Convert from AutoCad to Solidworks. Changes in design spec are OK if they make the case look better or increase manufacturing efficiency.

Also are looking to create an attachable- detachable piece. This piece will be on the right side of the case (opposite of the volume buttons) and will allow the consumer to clip-on or somehow attach a leather flap that lays over the Iphone screen.
You can completely change the right side of the case to create this piece. Open to any cool ideas! Try to keep it as slim as possible and efficient in terms of manufacturing.
Wants:
1. Accuracy of converting file
2. Readiness for manufacturing
3. Attachable piece!! Very important!!!
Software:
  1. SolidWorks
Additional Information
Update!!!!: Please ignore everything about the attachable piece/hinge. The side opposite the volume buttons should not have any holes. Also, please upload separate files for the rubber and the titanium pieces.

Autocad file uploaded!!

Thanks!

Entries

= Buyer's Rating
1st Winner
#6 Iphone Case- Rev01 by CAD SPARKLES
2nd Winner
#5 iphone 5 case by vinya
#1 I Phone Case by Nick Trep Designs
#2 rubber case iPhone5 by danby
#3 Iphone Case by CAD SPARKLES
Download Files
#4 iphone 5 case by vinya

Discussion

vinya

Designer

Fri, 21 Feb 2014 03:53:13 +0000
wow shadi let me know if there is anything more i can do for you!

vinya

Designer

Mon, 17 Feb 2014 05:33:58 +0000
who is the winner here!
Fri, 14 Feb 2014 04:11:38 +0000
Hello sir, I am new in this field can u give me some suggestions about this, like softwares rather than Solid Works.

ShadiB

Buyer

Fri, 07 Feb 2014 17:21:34 +0000
Vinya: you can use any thin trace for the wire on the aluminum...diameter is .5 mm. The rubber piece you are reffering to sits between the titanium and the aluminum

vinya

Designer

Fri, 07 Feb 2014 07:25:34 +0000
what is the diameter of the wire that will be laid on eliptiacal tatanium and why wire is there? i dont see round shaped rubber at the back its eliptical in attached file

ShadiB

Buyer

Mon, 27 Jan 2014 22:00:15 +0000
Yes, that is fine as long as it can be used as a DFM (.iges files)
Sat, 25 Jan 2014 04:12:39 +0000
Hi, Can I submit a design from Shark LT...? the design can be in format that will open in SolidWorks

ShadiB

Buyer

Fri, 24 Jan 2014 00:32:25 +0000
Fixed!

CAD SPARKLES

Designer

Thu, 23 Jan 2014 01:19:33 +0000
could not able to open the pdf file

Similar Contests on Cad Crowd

Silicone Ring 3D Design
Hi, I need a 3D CAD ring rendering that will be made into a silicone ring mold. The mold will be made of copper or stainless steel Our logo (attached) needs to be debossed on the inside. Please see attached files for the (very) rough 2D mockups Dimensions of the ring should be: Inside Diameter: 20.6mm Thickness: 1.75mm Width: 9mm Color: Black Here's a link to the original (tungsten) ring: http://www.giftflavors.com/tungsten-wedding-band-ring-10mm-wedding-band-for-men-women-all-sizes-18k-rose-gold-plated-designer-rings-comfort-fit-black-beveled-edge-brushed-polished-male-mans-his-hers-couple-sets-personalize-laser-engraving-available-lifetime-guarantee/ I'll be very responsive as I'm looking to finish & pay quickly on this as it's a rush job. Thanks!!
Unique, yet Simple, Card Holder Tray (Children's Board Game)
INTRODUCTION: Friends, I place this project in your capable hands... please help me move the cause forward! I'm a dad, and one-person start-up, using my retirement savings to develop a children's board game. (There's a real lack of truly funny reading games for kids aged 5-8 years. Most are really boring. My intention is to introduce a new board game at retail that fills the gap and gets younger kids laughing and reading.) ASSIGNMENT: Develop the production-ready Mini Card Holder Tray which will be used in the game. Deliverables (hope I got these right)... - A CAD and STL file which can be (a) used to 3D print a prototype/sample, (b) provided to a manufacturer for development of a mold and mass production of tray - A PDF showing the tray from 2-3 perspectives USE OF TRAY: This game includes miniature playing cards, and they are held in a card holder tray which is essential to game play. Play starts as the card tray slides over (on top of the table or playing surface) to Player 1. He draws his cards. After playing the cards, he pushes/slides the tray to Player 2. She'll take her turn, and slide the tray to the next player. Turns continue until the game ends. MAXIMUM DIMENSIONS OF TRAY: So the tray will fit in the game box, its size cannot exceed 170mm x 100mm x 35mm. CARD SLOTS IN TRAY: To ensure proper game play, the card slots (where the cards fit) must be as follows… - Left Side -- a front and rear slot to hold cards - Middle -- a single front slot to hold cards - Right Side -- a front and rear slot to hold cards Each tray opening/slot must be able to hold at least (35) 44 x 67mm mini playing cards... that's about 14mm deep. (Please also provide the appropriate extra space in the width of the card slots so the cards can be easily inserted and pulled out.) See attached image of my temporary tray (01_TempTray.jpg) that I cut up crudely from an ice cube mold, for a visual of the number of tray slots, and their orientation. THOUGHT-STARTERS FOR STYLE OF TRAY: I've seen two types of trays that could work well. See attached examples in PDF (02_TwoTrayTypes.jpg)... - Tray that lies flat (on its back) - Tray that holds cards somewhat upright (at an angle for viewing) Or maybe a hybrid of the two tray types? In terms of design, something that's simple, contemporary and visually pleasing (like Apple® products), would be great. I've attached an earlier mock up of the game's box cover, in case that can stimulate ideas also. (03_BoxCover_InProgress.jpg)
BXL1
We need a design/file ready for prototype printing and injection molding Product is placed in swimming pool skimmer or pump basket and is in constant water flow. We need a container to hold the copper/silver cilinder to give it a more MARKETABLE LOOK. Plastic container/packaging for blueray xl 4-in-1 Mineral Clarifier. check cilinder in bluerayxl.com. I will need 3 columns with a square plastic netting/strainer (about 3.5 x 5 mm). to let water thru but not debris. Top and bottom i'm attaching strainer sample. use drawing as a guide but keep yellow and blue cylinder sizes intact, container can change slightly in design and measurements.cilinder
Mosquito Trap Redesign
We want to redesign our UV LED mosquito trap, an outdoor product to be placed in tent, outdoor café, farms to reduce the damage by mosquito. It should be simple, solid, low priced, slim, good quality and fashionable- a mid-way between high-tech and disposable traps. We would like its housing to be partially transparent for the visibility of LED light. Also, we prefer the entry point for mosquito to be a maze design. Type: Mosquito trap Target Audience: All age groups Competitors: enclosed in attachments Design: Maze entry point, partially transparent body, UV LED light, PCB board, cotton stand to put cotton soaked in mosquito attractant liquid, 2AAA battery case Material: Plastic Any software is acceptable if STL format file can be provided Any further questions, please feel free to comment.
Universal Phone Mount
Hi Cad Crowd! We're in need of adjusting one of the components of our product. We have an existing 3D model that we need adjusted. We are keeping the same top and bottom connection the same. The basic design is similar to a standard universal phone mount for a car. We want to use the same mechanism as shown in the pictures and then adjust it to our requirements. The system will be 3 major components. Part 1: Back piece that has top connection and bottom connection which won't be changed much except for the width. This area will be where the gears/spring/everything sits on. Part 2: This will be the two "wing walls" that extrude left and right that will be sat on the back plate area. Part 3: Will enclose this area and have a bottom stub where the phones sit. We play on adding some little foam on the front of part 3 and on the insides of the wing walls. We think that the gear mechanism can be reduced in size and that we can flip it so that they sit above the wing walls (and in the center of the system).