IFGS: 30 Year Service Award Pin

Contest Ended, Winner(s) have been selected.
I am looking for someone to replicate the attached pin, or to create a close facsimile thereof. I am open to design suggestions; one of my ideas is to add three "X"s onto the pedestal of the dragon under the "IFGS"; perhaps as "xXx" or as three "X's of the same size with the center one raised at half the height of the other two "X"s. The pin is about 3 inches in height.

We need 10 of these items. They are Service Awards pins for the 30th anniversary of the IFGS (www.ifgs.org).

If you are willing and able to do this, I'd like a price quote and delivery schedule, please! We'd like the material to be silver, in a non-tarnish formulation if this is possible.

Thank you for your time and consideration in this matter.


Olan Knight
IFGS Society Board Member
1) Overall look 2) Overall size 3) Amount of material required for each pin 4) Design able to be created in Shapeways
Don't Wants:
1) Thick design that requires too much silver. 2) A design so thin that it is flimsy. 3) Something cheap looking.
  1. Collada
  2. OBJ
  3. X3D
  4. VRML2


1st Winner
#5 Drako Mark 2 by Cata
2013-06-05 15:59:16
#1 Drako Mark 1 by Cata
I understand that the contest has stoped for a while but if will resume, this is the model i came up with. If it's needed i can cut it in half because it might consume a lot of material in the manufacturing process. This is just for viewing the model itself it is not the final product. If the contest will resume I will provide a final product. I will be glad if the buyer can contact me and provide some feedback about the model. Thank You!
2013-05-30 18:29:30
#2 slic dragon pin by Lionel Glaro
Simple and slic pin design with dragon logo
2013-06-02 04:54:45
#4 Pin3 by Lionel Glaro
2013-06-02 09:38:17
#6 IFGS by Sergiu.Nasta
2013-06-09 03:54:06
#7 XxX IFGS by Sergiu.Nasta
2013-06-09 04:33:28
#8 Dragon pin final by Cata
I have modified the font of the "IFGS" and "xXx" to Old English Text font as you requested.
2013-06-13 20:23:25
#9 Dragon pin final by Cata
2013-06-14 02:46:48


Olan Knight


Thu, 13 Jun 2013 17:56:38 +0000
The Board likes this pin the best, but we'd like the FONT used for the "IFGS" and the "xXx" changed to either Old English Text (if possible) or to Times New Roman.

Can you send me an updated image file?

Olan Knight


Wed, 22 May 2013 20:50:23 +0000
ON HOLD: This contest is on hold effective 21-MAY-2013 as I have made arrangements with a particular designer. Should the design created not be acceptable, I will re-open this contest.

Many Thanks,
Olan Knight

Olan Knight


Wed, 22 May 2013 20:48:18 +0000
Sadly, that is the only picture that I have of the 20 year pin.
Wed, 22 May 2013 20:16:04 +0000
Do you have any other picture or design that can be used to see more details on this? It's a bit hard to see all the details on the dragon due to silver reflecting...

Similar Contests on Cad Crowd

1:64 Railway Stockcar - CAD Designer to Scale Down Model for 3D Printing
1:64 Stockcar. Modeling the later series with the end with the swinging open doors.
Air Dump 1:64 - CAD Designer to Scale Down Model for 3D Printing
Small air dump in 1:64 scale. Drawings from onsite measurements are provided are in 1:32 scale. Data sheet Mechanical drawing also available.
Design an Extraordinary Cabinet Knob or Pull
I own Knobs.co, a retail cabinet hardware site. I want to manufacture a line of unique, 3D printed cabinet hardware. This contest is for the design for one cabinet knob or pull. However, should I find a designer whose work I like, there could be far more work following. The final knobs will be produced in metal. They will need to be strong enough for daily use, stunning to look at, and capable of being screwed into a cabinet, which means they should have a threaded screw hole capable of receiving an 8-32 screw. The knob diameter can be anywhere between 1 1/4 inches and 1 1/2 inches. Also, the final piece needs to be capable of being submitted directly to Shapeways, and conform to all of their criteria for strength, wall thickness, etc. I'm not a techie, so if I have to modify anything to upload it, the knob is never going to get made.
Dental Tool
Mass produced plastic tool for dental product. My immediate need, however is to have 3-D prints made for evaluation. I'd also like to use the same file for manufacturing. Plan of tool, logo file, detail of head and pic of possible diamond-pattern knurling grip attached.