Mechanical jewellery

in 3D Modeling Design held by DD
Contest Ended, Winner(s) have been selected.
Description:
I have two 3d ring designs with a moving part. I would like the rings to be printed in steel and assembled after printing manually such that the moving part is inserted easily in the ring. Manual assembly can involve a lock, a latch, or screw mechanism that snaps the ring together never to come apart. The rings will be printed on shapeways.com.
Wants:
1. The files produced must be in STL form to be uploaded to shapeways but also must be in dx form to be viewed with 123D software.
2. The rings must follow the guidelines on the website for steel material. https://www.shapeways.com/materials/steel.
3. The design of both ring and moving part must pass through the testing of shapeways and splicing software.
4. You may enlarge the moving part if it lends itself to better printing or post processing.
5. All parts must fit AFTER processing.
Don't Wants:
a)A complete departure from the original design.
b) Rings should not be easily disassembled, i.e. it should lock into place.
Ask for Sample:
Please submit a sample for evaluation, SVG , STL .dx files (123D)
Software:
  1. Must be viewable and editable with 123D autocad

Entries

1st Winner
#7 Snap Together Mechanical Ring by Ryanv777
I hope this meets your expectations! See my private message for more details.
more
Jul 4, 2016 15:35
#4 Pear ring by John Paulo
Here it is the Pear.
more
Jul 1, 2016 0:03
#5 Mech Ring by John Paulo
The Revise
more
Jul 1, 2016 0:04
#1 mechanical ring by elmasry
Please rate this entry and feel free to ask for edit anything
more
Jun 8, 2016 13:41
#2 ring2 by elmasry
There my entry hope it pleases you
more
Jun 15, 2016 17:23
#3 Express your mode by Bacem Jarraya
by turning the mouth you change from smiling to sad face
more
Jun 26, 2016 23:36
#6 Cincin Mekanik by Ridwan Septyawan
"Cincin Mekanik"
I hope this is meet with your requirements.
All The Best,
Ridwan S
more
Jul 1, 2016 15:03

Discussion

DD

Buyer

Thu, 30 Jun 2016 20:43:36 +0000
Hi, the attachments are viewable and available on the same page.
Wed, 29 Jun 2016 14:25:22 +0000
Hello, why I can not see the attachments? Thank you.

Similar Contests on Cad Crowd

Imagine it
I need to make a companies Logo into a 3d model that would have the ability to be 3d printed in color sand stone and clear resin so there would be two separate STL files one of which would be a color stl file
Outdoor TV Enclosure
Design an outdoor TV Enclosure for 32" flat screen TV to be used outdoor such as backyard, pool, or cafeteria. - Inside the enclosure will hold flat screen TV with dimension of 30" x 18" x 2" (W x H x D). Dept can be extended if needed. - TV must be safely secure inside the enclosure when not attach to the VESA Wall mount - Must be able to mount with VESA Wall mount standard of 200mm x 200mm - Water resistant but does not need to be completely waterproofed - Have a cooling system, either ventilation for airflow (Fans) or cool down liquid (Freon) - A sound bar will be located in the bottom of the enclosure - Would be nice if the enclosure has feet that can be pushed in or pulled out when place on the ground to keep it balance.
Mechanical Engineer to develop light guides or light pipes used with LEDs
Looking for an engineer that has experience with light guides or light pipes used with LEDs, and that can design a few simple light guides for an electronic device. 3 LEDs - red, green, blue will feed the light pipe. the other end of the light pipe will be visible to the user thorugh a cutout in the enclosure. the user will see this end of the light pipe, which is 2 strips each at .2 wide x 2" long. there may be some curvature to these 2" long strips (maybe a radius of 2.5"). when the red LED is on the strips will light up red. same for green, etc. need to make sure the lighting is continuous (not brighter at one end than the other). Proven experience with LIght pipes is required. $100 for initial sketch and background proving that this design will work. Further work would then be given to winner to develop the concept into a injection molded part. Good Luck and I look forward to working with you.
Light integrated into side view mirror
I am looking for someone to design a sideview mirror with LED Lights integrated into the design. This is for the Jeep Wrangler JK. I plan on using led lights similar to the Rigid Industries 4in midnight edition, but integrated into the design.
Ecig
Hi everyone I have a cad draw of a battery case for a 18350 efest battery and I need some work in there to take it to production I need measurements and specifications of each part the battery dimensions are 18 mm diameter and 35 mm length