By The Sea

Contest Ended, Winner(s) have been selected.
Description:
An existing house is being renovated.
We have 2D sketches which have been approved by local council.
The pitched roof will be removed and replaced with a flat roof so that a roof terrace is created. This will have views of the ocean and entertaining equipment such as a BBQ and seating / lounge.
The existing living area on Level 2 will be extended as shown on drawings and new internal stairs allowing access from Level 2 to the roof terrace.
The kitchen, bathrooms, existing floors, lighting etc will all be replaced with new.
A garage will be installed on Level 1 (ground floor entry).
The house will effectively look totally different from the front with a new entrance, garage and new façade.
Wants:
We are looking for a modern style / beach feel.
You will find that the drawings may be a little inaccurate on some dimensions. We are not concerned with that as our builder will finalise exact details. We are more looking for an exceptional look and feel for the premises.
Don't Wants:
3D colour drawings. Façade, side views.
Internal colour schemes
Ask for Sample:
A sample of your capabilities would help assist in making a decision on who we proceed with. Perhaps you could send me your thoughts on the house?
Software:
  1. It isn't important as long as it provides the results
Additional Information
Please ignore my comment in the "Don't Wants".

I actually do want 3D drawings, rendered elevations, colour schemes etc

Entries

1st Winner
#5 BEACH HOUSE by Adam
2016-01-09 22:45:28
#4 BTS 1130 by re:designusa
COPYRIGHT DESIGN BY REDESIGN ARCHITECTURAL STUDIOS FOR SUBMITION TO CAD CROWD CONTEST ( MORE DETAIL AVAILABLE UPON CONTEST REWARD)
more
2016-01-08 05:32:50
#1 cottage by lazuch
2016-01-07 01:22:28
#2 CRAFTSMAN HOUSE AND HOLIDAY CABIN HOME by Carrara1
The submitted visuals are artist impressions of the day and night scenes of a craftsman house and a holiday cabin, of which were modelled in Rhino 3d and rendered in Cinema 4D. Also submitted are 2 sample interior design visuals.
more
2016-01-07 01:44:32
#3 My home design by jscanlon35
2016-01-07 11:52:02

Discussion

re:designusa

Designer

Thu, 07 Jan 2016 03:34:01 +0000
Hey Ric, working on a submission here now, in the mean time you could check my portfolio out with a few "beach" or coastal properties ive done.

https://www.pinterest.com/redesignusa/redesign-portfolio/

Aaron Robinson

Ric Drigo

Buyer

Thu, 07 Jan 2016 00:00:42 +0000
My apologies.
These are actually my wants.
I misread the line
Thank you for picking this up
Wed, 06 Jan 2016 13:33:39 +0000
Hello sir,

What do you mean by "Don`t Wants: 3D colour drawings" ?

Similar Contests on Cad Crowd

Handle / Grip design with gear & Latch
The design needed is for a handle / grip that when squeezed, it will make a 3/8" square bar, which is in a 1 1/2" high extruded piece, travel aprox 2 1/2" towards the grip. See short video. This also needs to be able to lock into multiple positions when squeezed and also have an easy release so that when released it springs back into its original open position. This will be attached to the end of the 1 1/2" high extrusion. There are 2 openings in this extrusion. One along the top will be a square opening in which the 3/8" square bar will be encased and the other one will be a round hole which will encase a 3/8" round tube in which water will travel through. This round tube will need to extend out the back of the extrusion and through the handle and attach to a water hose. The handle / grip needs to extend up above the extrusion a minimal amount. The attached picture of my prototype extends way too high above the extrusion. One thought is to incorporate a rack and pinion type gear to achieve this. Any type of gear or mechanism will need to be enclosed in the handle.
Universal Phone Mount
Hi Cad Crowd! We're in need of adjusting one of the components of our product. We have an existing 3D model that we need adjusted. We are keeping the same top and bottom connection the same. The basic design is similar to a standard universal phone mount for a car. We want to use the same mechanism as shown in the pictures and then adjust it to our requirements. The system will be 3 major components. Part 1: Back piece that has top connection and bottom connection which won't be changed much except for the width. This area will be where the gears/spring/everything sits on. Part 2: This will be the two "wing walls" that extrude left and right that will be sat on the back plate area. Part 3: Will enclose this area and have a bottom stub where the phones sit. We play on adding some little foam on the front of part 3 and on the insides of the wing walls. We think that the gear mechanism can be reduced in size and that we can flip it so that they sit above the wing walls (and in the center of the system).
Help me jazz-up a home audio component enclosure!
- I am attaching front and side panel drawings for a home audio component. - The location for the knobs and holes are to be fixed, but I'm looking to see a 3D model, with my logo added to the top-center of the front panel. - Add text for the buttons / knobs (I will provide the text, and you play with the font/size). - Front / side panels to be BLACK (with white silk screen). Also want to see the same thing with front / side panels in SILVER (with black silk screen). - Play with the beveling to give the panel some character, but nothing over the top. - No need to be concerned with the rear panel or bottom for this project. - Perhaps we can put the company icon from the logo on the top panel. I'm open to ideas. - I need help with the design of the two large knobs. They will be aluminum. Need a design for them. - Display shown on center of front panel consists of (3) 7-segment LED displays.
Bottle Design
My company as of now will sell stainless steel water bottles. The bottle will be designed to keep beverages cold for 24 hours and hot for 12 hours. The purpose of the design will be for me to send it to a company that will mass manufacture the bottle. The heart portion needs to appear more as if it is coming from the inside out vs it being screwed or glued on to the outside of the bottle as it is pictured. It would also only read 'Jorvine'.
UAV Reaper Drone
Need complete design for Reaper Drone in solid Works for each part of the stucture (Fuselage+ wings+ wheels) no need for engine and inside equipements, and i don't need rocket design and no need also for 2D drafting