Door Pulls
in
3D Modeling Design
held by
Marcus Cumberland
Last seen:
Contest Ended, Winner(s) have been selected.
-
Open
-
Choosing Finalist
-
Ended
Description:
I am designing bespoke door pulls for a classic porsche 911
Wants:
- Details in the PPT file Attached. - I want the PPT details converted into CAD so I can get the components produced.
- I am limited to my skills in the PPT, as I would want some small radius' which I can't document in the PPT
Software:
- DXF
Prepaid PrizeEntries
Discussion
submitted, I can make changes to anything you need in this file.
How thick is the belt
Thanks for responding.
Black element is a leather belt, that I have draw across two pages, so I could keep the drawing life size.
The total belt length should be 38cm
The three stainless steel elements retain the belts in different ways. The element on the far right is just retains the belt to the door panel allowing the belt to move freely below as a grab handle, like on a trunk.
The middle elements, restricts the belts, so although the belt passes through and is retained to the door panel, the belt cannot move.
The left element, is slightly different again, in the is masks a slot in the door panel where the belts slips behind the panel to operate to door opener. This element does no restrict the movement of the belt, potentially offer some retaining properties, but purpose of to match the other elements and allow the leather belt to pass from the front of the door panel to the rear, in a tidy way.
This one leather belt, operates as a handle on the right side, and as a door release on the left side.
I have drawn these as square, as it was easy to do this on PowerPoint, however there should be small radius on the tops of these pieces so they are nice to touch.
I will attached an image of something similar that I saw, however in the attached drawing the radius are more than I would be looking for, but I think you will understand my project more.
Black element is a leather belt, that I have draw across two pages, so I could keep the drawing life size.
The total belt length should be 38cm
The three stainless steel elements retain the belts in different ways. The element on the far right is just retains the belt to the door panel allowing the belt to move freely below as a grab handle, like on a trunk.
The middle elements, restricts the belts, so although the belt passes through and is retained to the door panel, the belt cannot move.
The left element, is slightly different again, in the is masks a slot in the door panel where the belts slips behind the panel to operate to door opener. This element does no restrict the movement of the belt, potentially offer some retaining properties, but purpose of to match the other elements and allow the leather belt to pass from the front of the door panel to the rear, in a tidy way.
This one leather belt, operates as a handle on the right side, and as a door release on the left side.
I have drawn these as square, as it was easy to do this on PowerPoint, however there should be small radius on the tops of these pieces so they are nice to touch.
I will attached an image of something similar that I saw, however in the attached drawing the radius are more than I would be looking for, but I think you will understand my project more.
Hello!
I am currently in the process of converting the PPT file to CAD but I have one question:
Since the door pull is split into two pages, it is hard to tell how the two are supposed to connect to one another, especially since the left side of the door pull has unknown dimensions. I tried to figure it out but the pieces don't seem to "fit" together.
Could you please clarify how the two are supposed to connect.
Thank you!
-Kristin
I am currently in the process of converting the PPT file to CAD but I have one question:
Since the door pull is split into two pages, it is hard to tell how the two are supposed to connect to one another, especially since the left side of the door pull has unknown dimensions. I tried to figure it out but the pieces don't seem to "fit" together.
Could you please clarify how the two are supposed to connect.
Thank you!
-Kristin
Similar Contests on Cad Crowd
Heart shaped charm/pendant for a necklace w/ chinese symbol
I'd like a heart shaped pendant for a necklace that incorporates the chinese symbol for love (see attachment). There is plenty of room for creativity and i look forward to working with you on making this an attractive gift for my wife.
T-Shirt
cv b
CROISSANTERIA DO BAIRRO
Need a Bakery Kiosk (4x4m^2) design/futuristic/minimalist look, with shape of croissant on the ground. Maybe cork material. Please keep this simple, to have costs and time to make it faster.
The kiosk itself is limited to 4x4, the floor can be bigger. It is for a shopping mall. It is a French Chef Bakery/Coffee Shop that serves croissants, chocolate and coffee. Attached are some pictures of the feel we look for. We need the implementation in 3D and 2D measurements to send to the Shopping mall Administration for Approval. THIS PROJECT CAN'T TAKE MORE THAN ONE DAY. IT IS OF EXTREME URGENCY! NO BS.
ArtCam 3D Modelling of Wooden Furniture
We are basically looking for Artcam designers, for 2D & 3D modelling of various wooden furniture & stuffs.
we have long term requirement, initial order of almost 20 to 25 Bed models for now.
##Note: Rates per model could be decided on discussion.
J-shape
3D modeling of a J-shaped massage tool, much like a Theracane only smaller in dimensions. The tool should be modeled as close as possible to the attached images. The straight portion of the J-shape is approximately 10 inches long and 3/8in in diameter. The hook portion of the tool should form an approximately 180 degree arc and terminate in spherical end of 9/16in diameter. The handle, at the top of the J-shape, should be approximately 3/4in in diameter. The attached jpg images are of the actual tool that I would like modeled and should give you a good idea of it's dimensions. The png file should also provide a good reference. Thanks.
sldraftingdesign
Designer