Remote
Work location
Reverse engineer car trim Ended
About the job
Hello
Im look to reverse engineer car trim that are shown in the picture 2parts passenger side (small and big part)
2parts driver side( small and big part)
I can have the parts 3d scanned but i want to get a rough estimate of the total cost first
The parts need to be suitable for 3d printing and enforced on the clip locations can be split from original parts and printed alone then reattach using heat set inserts on the original parts and bolts the clip into the original part
and the big part will have to be made in 2 interlocking parts as 3d printer max print size is 320×320×320mm
The design should not include the switches in the picture
I can have all the parts 3d scanned when accepting an offer
initial IR scan done for the LHS big part.... reverse engineering for the parts without the switches
Im look to reverse engineer car trim that are shown in the picture 2parts passenger side (small and big part)
2parts driver side( small and big part)
I can have the parts 3d scanned but i want to get a rough estimate of the total cost first
The parts need to be suitable for 3d printing and enforced on the clip locations can be split from original parts and printed alone then reattach using heat set inserts on the original parts and bolts the clip into the original part
and the big part will have to be made in 2 interlocking parts as 3d printer max print size is 320×320×320mm
The design should not include the switches in the picture
I can have all the parts 3d scanned when accepting an offer
initial IR scan done for the LHS big part.... reverse engineering for the parts without the switches
Hello
Im look to reverse engineer car trim that are shown in the picture 2parts passenger side (small and big part)
2parts driver side( small and big part)
I can have the parts 3d scanned but i want to get a rough estimate of the total cost first
The parts need to be suitable for 3d printing and enforced on the clip locations can be split from original parts and printed alone then reattach using heat set inserts on the original parts and bolts the clip into the original part
and the big part will have to be made in 2 interlocking parts as 3d printer max print size is 320×320×320mm
The design should not include the switches in the picture
I can have all the parts 3d scanned when accepting an offer
initial IR scan done for the LHS big part.... reverse engineering for the parts without the switches
Im look to reverse engineer car trim that are shown in the picture 2parts passenger side (small and big part)
2parts driver side( small and big part)
I can have the parts 3d scanned but i want to get a rough estimate of the total cost first
The parts need to be suitable for 3d printing and enforced on the clip locations can be split from original parts and printed alone then reattach using heat set inserts on the original parts and bolts the clip into the original part
and the big part will have to be made in 2 interlocking parts as 3d printer max print size is 320×320×320mm
The design should not include the switches in the picture
I can have all the parts 3d scanned when accepting an offer
initial IR scan done for the LHS big part.... reverse engineering for the parts without the switches
Hello
Im look to reverse engineer car trim that are shown in the picture 2parts passenger side (small and big part)
2parts driver side( small and big part)
I can have the parts 3d scanned but i want to get a rough estimate of the total cost first
The parts need to be suitable for 3d printing and enforced on the clip locations can be split from original parts and printed alone then reattach u... read more
Im look to reverse engineer car trim that are shown in the picture 2parts passenger side (small and big part)
2parts driver side( small and big part)
I can have the parts 3d scanned but i want to get a rough estimate of the total cost first
The parts need to be suitable for 3d printing and enforced on the clip locations can be split from original parts and printed alone then reattach u... read more
Hello
Im look to reverse engineer car trim that are shown in the picture 2parts passenger side (small and big part)
2parts driver side( small and big part)
I can have the parts 3d scanned but i want to get a rough estimate of the total cost first
The parts need to be suitable for 3d printing and enforced on the clip locations can be split from original parts and printed alone then reattach using heat set inserts on the original parts and bolts the clip into the original part
and the big part will have to be made in 2 interlocking parts as 3d printer max print size is 320×320×320mm
The design should not include the switches in the picture
I can have all the parts 3d scanned when accepting an offer
initial IR scan done for the LHS big part.... reverse engineering for the parts without the switches read less
Im look to reverse engineer car trim that are shown in the picture 2parts passenger side (small and big part)
2parts driver side( small and big part)
I can have the parts 3d scanned but i want to get a rough estimate of the total cost first
The parts need to be suitable for 3d printing and enforced on the clip locations can be split from original parts and printed alone then reattach using heat set inserts on the original parts and bolts the clip into the original part
and the big part will have to be made in 2 interlocking parts as 3d printer max print size is 320×320×320mm
The design should not include the switches in the picture
I can have all the parts 3d scanned when accepting an offer
initial IR scan done for the LHS big part.... reverse engineering for the parts without the switches read less
Things to know
Any
Skill Level
Open budget
Fixed-rate
Full-time
Job type
Under 1-month
Job duration
Areas of expertise
3D Modeling
3D Print
3D Printing Design
Mechanical Design
Reverse Engineering
+2 more
Job categories
Reverse Engineering
3D Printing Design
3D Design Services
About the client
Payment ready
Kuwait (04:51 am)
Posted
Active
Job activity
23 Applicants
1 interviews in progress
5 unanswered invites
More open jobs from this client (2)
Design exhaust manifold
Remote - Posted
Hi
I have a 3d scan of exhaust manifold and would like to reverse engineer for slm 3d metal printing .. dont mind the log manifold design .... would like to have 3in vband a...
Design Engineering Services
Mechanical Engineering
3D Modeling
View job
Design panel cover
Remote - Posted
I need a car cover design for under dash for corvette c5 (not oem replica) just to cover the one side and hold a switch mounting available points in red
Using this 3d scan...
Automotive Design
3D Printing Design
Reverse Engineering
View job
Similar jobs
3D-CAD Planer-in / 3D CAD Draftsperson.
Remote - Posted
Profil:
. Technischer CAD-Zeichne mit 2-3 Jahre Erfahrung
. Sehr gute SolidWorks-Kenntnisse
. Erfahrung 3D-Zeichnungen
. Erfahrung im Bereich Maschinenbau, Anlagenbau, L...
3D Modeling
3D Design Services
Engineering Design
View job
RMU Design with VCB
Remote - Posted
We need RMU with one 630A VCB and two Load break switches/Isolators. Design stanadards are as attached. We need 100% Guaranteed design to pass the CPRI testing on enclosure an...
Electrical Engineering
Fabrication Drawings Services
3D Design Services
View job
Freelancer Architectural Cad Operator
India - Posted
I am looking for sincere, committed Freelancer Architectural Cad Operator ONLY from India.
Architects, Interior Designers, Engineers Need Not reply PLEASE.
Architectural Drawing Services
3D Design Services
3D Modeling
View job
Flygt Submersble Pump Modular Pontoon Design
Remote - Posted
I'm looking for someone who can design a modular pontoon for a flygt submersible pump BS 2201.I have the GA drawings for the pump and concepts of how the pontoon is to be. At...
Mechanical Engineering
3D Design Services
3D Modeling
View job
Mechanical Drawings and Footprints for Connectors
Remote - Posted
We're looking for someone to generate 3D/2D mechanical drawings for 35 of our connector parts from existing SolidWorks models, along with PCB footprints, for use in our produc...
Mechanical Drawing Services
3D Design Services
3D Modeling
View job
popsicle transfer unit
Remote - Posted
a rotary popsicle machine has a round pull up arms taking the popsicles from the mold then release them to the conveyer belt , the step from the arm to the belt is missing , i...
Mechanical Engineering
3D Design Services
3D Modeling
View job
How it works
Find hourly jobs
Top rated experts are regularly hired for hourly jobs & ongoing client work.
Fixed-rate jobs
Experts can browse & apply to fixed-rate work & quote on a flat-rate basis.
Design contests
Experts build a reputation and earn prizes by participating in design challenges.
About Cad Crowd
4.9/5.0
(Our client satisfaction)
G2 2022
Spring high performer
210,221
global members
33,381
projects delivered to clients
Trusted by
