Remote
Work location
PCB Designer Needed — Automotive GPS/LTE Tracker (ESP32-S3, A7670E, Dual CAN Bus) Ended
About the job
Commercial Vehicle GPS Tracker PCB Design — Production Ready for JLCPCB
I am developing a commercial vehicle GPS tracking device targeting the fleet management market. I already have a complete BOM and clear technical requirements. I am looking for an experienced embedded hardware/PCB designer to deliver fully production-ready files suitable for JLCPCB turnkey assembly.
The device includes:
ESP32-S3-WROOM-1 (N8R8) as the main MCU
A7670E LTE Cat-1 modem
u-blox NEO-M8N GPS module
Dual MCP2515 + dual TJA1050 — two independent CAN bus interfaces
CAN1 for OBD2 communication
CAN2 for body/proprietary vehicle networks
TPS54360 buck converter for automotive power input (9–36V)
Reverse polarity protection
ADXL345 accelerometer
W25Q128 SPI flash
USB-C for firmware flashing and debugging
SIM card holder
Automotive environment and power stability considerations
Deliverables Required
Complete schematic design
2-layer PCB layout (compact form factor, target under 100mm × 80mm)
Gerber files ready for JLCPCB manufacturing
BOM in JLCPCB-compatible format with LCSC part numbers where possible
Pick-and-place (CPL) file
DFM review/check before final delivery
Important Requirements
JLCPCB assembly compatibility is mandatory
Proper LTE and GPS antenna placement and routing is critical
I will provide the full BOM; the designer should review it and flag any issues, improvements, or compatibility concerns
KiCad or EasyEDA preferred
Board should be designed with manufactura... read more
I am developing a commercial vehicle GPS tracking device targeting the fleet management market. I already have a complete BOM and clear technical requirements. I am looking for an experienced embedded hardware/PCB designer to deliver fully production-ready files suitable for JLCPCB turnkey assembly.
The device includes:
ESP32-S3-WROOM-1 (N8R8) as the main MCU
A7670E LTE Cat-1 modem
u-blox NEO-M8N GPS module
Dual MCP2515 + dual TJA1050 — two independent CAN bus interfaces
CAN1 for OBD2 communication
CAN2 for body/proprietary vehicle networks
TPS54360 buck converter for automotive power input (9–36V)
Reverse polarity protection
ADXL345 accelerometer
W25Q128 SPI flash
USB-C for firmware flashing and debugging
SIM card holder
Automotive environment and power stability considerations
Deliverables Required
Complete schematic design
2-layer PCB layout (compact form factor, target under 100mm × 80mm)
Gerber files ready for JLCPCB manufacturing
BOM in JLCPCB-compatible format with LCSC part numbers where possible
Pick-and-place (CPL) file
DFM review/check before final delivery
Important Requirements
JLCPCB assembly compatibility is mandatory
Proper LTE and GPS antenna placement and routing is critical
I will provide the full BOM; the designer should review it and flag any issues, improvements, or compatibility concerns
KiCad or EasyEDA preferred
Board should be designed with manufactura... read more
Commercial Vehicle GPS Tracker PCB Design — Production Ready for JLCPCB
I am developing a commercial vehicle GPS tracking device targeting the fleet management market. I already have a complete BOM and clear technical requirements. I am looking for an experienced embedded hardware/PCB designer to deliver fully production-ready files suitable for JLCPCB turnkey assembly.
The device includes:
ESP32-S3-WROOM-1 (N8R8) as the main MCU
A7670E LTE Cat-1 modem
u-blox NEO-M8N GPS module
Dual MCP2515 + dual TJA1050 — two independent CAN bus interfaces
CAN1 for OBD2 communication
CAN2 for body/proprietary vehicle networks
TPS54360 buck converter for automotive power input (9–36V)
Reverse polarity protection
ADXL345 accelerometer
W25Q128 SPI flash
USB-C for firmware flashing and debugging
SIM card holder
Automotive environment and power stability considerations
Deliverables Required
Complete schematic design
2-layer PCB layout (compact form factor, target under 100mm × 80mm)
Gerber files ready for JLCPCB manufacturing
BOM in JLCPCB-compatible format with LCSC part numbers where possible
Pick-and-place (CPL) file
DFM review/check before final delivery
Important Requirements
JLCPCB assembly compatibility is mandatory
Proper LTE and GPS antenna placement and routing is critical
I will provide the full BOM; the designer should review it and flag any issues, improvements, or compatibility concerns
KiCad or EasyEDA preferred
Board should be designed with manufacturability, automotive reliability, and clean signal routing in mind
Ideal Candidate
The ideal candidate should:
Have prior experience designing ESP32 or similar embedded systems boards
Be familiar with CAN bus design, LTE modem integration, GNSS/GPS integration, and automotive power input protection
Have previously submitted production boards to JLCPCB or PCBWay
Be able to provide examples or a portfolio of similar completed embedded or automotive PCB projects
Budget
Fixed price: $150–$350 USD depending on experience and portfolio
Timeline
Expected timeline: 5–6 weeks for all deliverables
To Apply Please Include
Portfolio examples of similar embedded, telematics, IoT, or automotive boards
Which PCB design software/tool you use
Your estimated timeline
Your fixed price quote read less
I am developing a commercial vehicle GPS tracking device targeting the fleet management market. I already have a complete BOM and clear technical requirements. I am looking for an experienced embedded hardware/PCB designer to deliver fully production-ready files suitable for JLCPCB turnkey assembly.
The device includes:
ESP32-S3-WROOM-1 (N8R8) as the main MCU
A7670E LTE Cat-1 modem
u-blox NEO-M8N GPS module
Dual MCP2515 + dual TJA1050 — two independent CAN bus interfaces
CAN1 for OBD2 communication
CAN2 for body/proprietary vehicle networks
TPS54360 buck converter for automotive power input (9–36V)
Reverse polarity protection
ADXL345 accelerometer
W25Q128 SPI flash
USB-C for firmware flashing and debugging
SIM card holder
Automotive environment and power stability considerations
Deliverables Required
Complete schematic design
2-layer PCB layout (compact form factor, target under 100mm × 80mm)
Gerber files ready for JLCPCB manufacturing
BOM in JLCPCB-compatible format with LCSC part numbers where possible
Pick-and-place (CPL) file
DFM review/check before final delivery
Important Requirements
JLCPCB assembly compatibility is mandatory
Proper LTE and GPS antenna placement and routing is critical
I will provide the full BOM; the designer should review it and flag any issues, improvements, or compatibility concerns
KiCad or EasyEDA preferred
Board should be designed with manufacturability, automotive reliability, and clean signal routing in mind
Ideal Candidate
The ideal candidate should:
Have prior experience designing ESP32 or similar embedded systems boards
Be familiar with CAN bus design, LTE modem integration, GNSS/GPS integration, and automotive power input protection
Have previously submitted production boards to JLCPCB or PCBWay
Be able to provide examples or a portfolio of similar completed embedded or automotive PCB projects
Budget
Fixed price: $150–$350 USD depending on experience and portfolio
Timeline
Expected timeline: 5–6 weeks for all deliverables
To Apply Please Include
Portfolio examples of similar embedded, telematics, IoT, or automotive boards
Which PCB design software/tool you use
Your estimated timeline
Your fixed price quote read less
Commercial Vehicle GPS Tracker PCB Design — Production Ready for JLCPCB
I am developing a commercial vehicle GPS tracking device targeting the fleet management market. I already have a complete BOM and clear technical requirements. I am looking for an experienced embedded hardware/PCB designer to deliver fully production-ready files suitable for JLCPCB turnkey assembly.
The device includes:
ESP... read more
I am developing a commercial vehicle GPS tracking device targeting the fleet management market. I already have a complete BOM and clear technical requirements. I am looking for an experienced embedded hardware/PCB designer to deliver fully production-ready files suitable for JLCPCB turnkey assembly.
The device includes:
ESP... read more
Commercial Vehicle GPS Tracker PCB Design — Production Ready for JLCPCB
I am developing a commercial vehicle GPS tracking device targeting the fleet management market. I already have a complete BOM and clear technical requirements. I am looking for an experienced embedded hardware/PCB designer to deliver fully production-ready files suitable for JLCPCB turnkey assembly.
The device includes:
ESP32-S3-WROOM-1 (N8R8) as the main MCU
A7670E LTE Cat-1 modem
u-blox NEO-M8N GPS module
Dual MCP2515 + dual TJA1050 — two independent CAN bus interfaces
CAN1 for OBD2 communication
CAN2 for body/proprietary vehicle networks
TPS54360 buck converter for automotive power input (9–36V)
Reverse polarity protection
ADXL345 accelerometer
W25Q128 SPI flash
USB-C for firmware flashing and debugging
SIM card holder
Automotive environment and power stability considerations
Deliverables Required
Complete schematic design
2-layer PCB layout (compact form factor, target under 100mm × 80mm)
Gerber files ready for JLCPCB manufacturing
BOM in JLCPCB-compatible format with LCSC part numbers where possible
Pick-and-place (CPL) file
DFM review/check before final delivery
Important Requirements
JLCPCB assembly compatibility is mandatory
Proper LTE and GPS antenna placement and routing is critical
I will provide the full BOM; the designer should review it and flag any issues, improvements, or compatibility concerns
KiCad or EasyEDA preferred
Board should be designed with manufacturability, automotive reliability, and clean signal routing in mind
Ideal Candidate
The ideal candidate should:
Have prior experience designing ESP32 or similar embedded systems boards
Be familiar with CAN bus design, LTE modem integration, GNSS/GPS integration, and automotive power input protection
Have previously submitted production boards to JLCPCB or PCBWay
Be able to provide examples or a portfolio of similar completed embedded or automotive PCB projects
Budget
Fixed price: $150–$350 USD depending on experience and portfolio
Timeline
Expected timeline: 5–6 weeks for all deliverables
To Apply Please Include
Portfolio examples of similar embedded, telematics, IoT, or automotive boards
Which PCB design software/tool you use
Your estimated timeline
Your fixed price quote read less
I am developing a commercial vehicle GPS tracking device targeting the fleet management market. I already have a complete BOM and clear technical requirements. I am looking for an experienced embedded hardware/PCB designer to deliver fully production-ready files suitable for JLCPCB turnkey assembly.
The device includes:
ESP32-S3-WROOM-1 (N8R8) as the main MCU
A7670E LTE Cat-1 modem
u-blox NEO-M8N GPS module
Dual MCP2515 + dual TJA1050 — two independent CAN bus interfaces
CAN1 for OBD2 communication
CAN2 for body/proprietary vehicle networks
TPS54360 buck converter for automotive power input (9–36V)
Reverse polarity protection
ADXL345 accelerometer
W25Q128 SPI flash
USB-C for firmware flashing and debugging
SIM card holder
Automotive environment and power stability considerations
Deliverables Required
Complete schematic design
2-layer PCB layout (compact form factor, target under 100mm × 80mm)
Gerber files ready for JLCPCB manufacturing
BOM in JLCPCB-compatible format with LCSC part numbers where possible
Pick-and-place (CPL) file
DFM review/check before final delivery
Important Requirements
JLCPCB assembly compatibility is mandatory
Proper LTE and GPS antenna placement and routing is critical
I will provide the full BOM; the designer should review it and flag any issues, improvements, or compatibility concerns
KiCad or EasyEDA preferred
Board should be designed with manufacturability, automotive reliability, and clean signal routing in mind
Ideal Candidate
The ideal candidate should:
Have prior experience designing ESP32 or similar embedded systems boards
Be familiar with CAN bus design, LTE modem integration, GNSS/GPS integration, and automotive power input protection
Have previously submitted production boards to JLCPCB or PCBWay
Be able to provide examples or a portfolio of similar completed embedded or automotive PCB projects
Budget
Fixed price: $150–$350 USD depending on experience and portfolio
Timeline
Expected timeline: 5–6 weeks for all deliverables
To Apply Please Include
Portfolio examples of similar embedded, telematics, IoT, or automotive boards
Which PCB design software/tool you use
Your estimated timeline
Your fixed price quote read less
Things to know
Intermediate
Skill Level
$350
Fixed-rate (USD)
Part-time
Job type
1-3 months
Job duration
Areas of expertise
Automotive Electrical Design
CAN Bus
ESP32
EasyEDA
Gerber Files
KiCad
Schematic Design
+4 more
Job categories
Electronics Design Service
Electrical Engineering
Product Engineering Services
PCB Design Services
+1 more
Languages
English
Limited working proficiency
About the client
Payment not ready
Botswana (07:59 am)
Posted
Active
Job activity
26 Applicants
0 interviews in progress
Similar jobs
Hardware Engineer / PCB Designer – Radxa CM5 (RK3588) Carrier Board Development
Remote - Posted
We are looking for an experienced Hardware Engineer / PCB Designer to develop a custom Carrier Board for the Radxa CM5 (RK3588S2) module.
The project will be based primaril...
Engineering Design
Electronics Design Service
Electronic Prototyping and Design Services
PCB Design Services
Mechanical Engineering
View job
Plastic enclosure for elecric plug.
Remote - Posted
I need 3D design for molding the small plastic part.
Product Engineering Services
Industrial Design Services
3D Modeling
View job
CAD designer needed to model 3D consumer product
Remote - Posted
We need a part-time 3D artist to help with an ongoing 3D rendering for our company furniture. The work will involve taking 2D drawings from our manufacturer in China and conve...
2D CAD Design Services
Industrial Design Services
Product Engineering Services
View job
Freelance mechanical spring designer
Remote - Posted
Need to design coil type spring as per data attached. Need the following details per sl.no. of spring.
A) length of the spring
B) no. Of coils ( as minimum as possible)
C)...
Mechanical Design Services
Product Engineering Services
Machine Design
View job
PCB Layout Engineer
Irvine, United States - Posted
Required Qualifications
Strong experience in PCB layout design for multilayer boards.
Experience in footprint creation, verification, and library management.
Knowledge of I...
PCB Design Services
Electronic Prototyping and Design Services
Electrical Engineering
View job
ACRYLIC DIYA
Remote - Posted
acrlic diya need to be given for lasercut .drawing needed for that
2D CAD Drafting Services
Industrial Design Services
Product Engineering Services
View job
How it works
Find hourly jobs
Top rated experts are regularly hired for hourly jobs & ongoing client work.
Fixed-rate jobs
Experts can browse & apply to fixed-rate work & quote on a flat-rate basis.
Design contests
Experts build a reputation and earn prizes by participating in design challenges.
About Cad Crowd
4.9/5.0
(Our client satisfaction)
G2 2022
Spring high performer
213,651
global members
33,455
projects delivered to clients
Trusted by
