Remote
Work location
Finite Element Analysis Ended
About the job
FEA of Mild Steel Pipe Assembly (Swinging and Static Load Analysis – Phase 1)
We are looking for an experienced FEA engineer to perform structural analysis on a simple pipe assembly made of mild steel (yield ≈ 250 MPa).
Assembly Details :
1. Handle Pipe (Hollow)
- Outer Diameter: 40 mm
- Length: 1000 mm
2. Weight Plates
- Total mass: ~20 kg
- Clamped directly to the end of the handle pipe
- Mounted using two cylindrical pins (one at the
top and one at the bottom)
- Approximate stack height: 120 mm
Analysis Requirements – Phase 1
1. Evaluate stresses and deflections under:
- Self-weight
- Swinging conditions at 1 RPM, considering
centrifugal forces of 20 kg at a 0.9 m radius
- Force due to sudden stop during swings, treated
as the resultant of the momentum of the weight
plate (a sudden-stop load, not an impact)
2. Use bonded contacts and bolt/pin connectors
(simplified setup acceptable)
Deliverables
1. Minimum required wall thickness of the handle
pipe
2. Minimum required pin and hole diameters
3. Stress and deflection plots, including safety
factors
4. Consideration of forces due to sudden stop
during swings
5. Final PDF report and editable FEA source file
When Applying, Please Include
1. Estimated cost and lead time for Phase 1
2. Example screenshots or reports from similar FEA
projects
3. The software you’ll use (e.g., ANSYS, SolidWorks
S... read more
We are looking for an experienced FEA engineer to perform structural analysis on a simple pipe assembly made of mild steel (yield ≈ 250 MPa).
Assembly Details :
1. Handle Pipe (Hollow)
- Outer Diameter: 40 mm
- Length: 1000 mm
2. Weight Plates
- Total mass: ~20 kg
- Clamped directly to the end of the handle pipe
- Mounted using two cylindrical pins (one at the
top and one at the bottom)
- Approximate stack height: 120 mm
Analysis Requirements – Phase 1
1. Evaluate stresses and deflections under:
- Self-weight
- Swinging conditions at 1 RPM, considering
centrifugal forces of 20 kg at a 0.9 m radius
- Force due to sudden stop during swings, treated
as the resultant of the momentum of the weight
plate (a sudden-stop load, not an impact)
2. Use bonded contacts and bolt/pin connectors
(simplified setup acceptable)
Deliverables
1. Minimum required wall thickness of the handle
pipe
2. Minimum required pin and hole diameters
3. Stress and deflection plots, including safety
factors
4. Consideration of forces due to sudden stop
during swings
5. Final PDF report and editable FEA source file
When Applying, Please Include
1. Estimated cost and lead time for Phase 1
2. Example screenshots or reports from similar FEA
projects
3. The software you’ll use (e.g., ANSYS, SolidWorks
S... read more
FEA of Mild Steel Pipe Assembly (Swinging and Static Load Analysis – Phase 1)
We are looking for an experienced FEA engineer to perform structural analysis on a simple pipe assembly made of mild steel (yield ≈ 250 MPa).
Assembly Details :
1. Handle Pipe (Hollow)
- Outer Diameter: 40 mm
- Length: 1000 mm
2. Weight Plates
- Total mass: ~20 kg
- Clamped directly to the end of the handle pipe
- Mounted using two cylindrical pins (one at the
top and one at the bottom)
- Approximate stack height: 120 mm
Analysis Requirements – Phase 1
1. Evaluate stresses and deflections under:
- Self-weight
- Swinging conditions at 1 RPM, considering
centrifugal forces of 20 kg at a 0.9 m radius
- Force due to sudden stop during swings, treated
as the resultant of the momentum of the weight
plate (a sudden-stop load, not an impact)
2. Use bonded contacts and bolt/pin connectors
(simplified setup acceptable)
Deliverables
1. Minimum required wall thickness of the handle
pipe
2. Minimum required pin and hole diameters
3. Stress and deflection plots, including safety
factors
4. Consideration of forces due to sudden stop
during swings
5. Final PDF report and editable FEA source file
When Applying, Please Include
1. Estimated cost and lead time for Phase 1
2. Example screenshots or reports from similar FEA
projects
3. The software you’ll use (e.g., ANSYS, SolidWorks
Simulation, Fusion 360, Abaqus, etc.) and
confirmation that it supports bolt/pin connectors
4. Number of revisions included
5. Confirmation that you will provide:
Editable FEA source file
Final PDF report
Additional Notes
We have additional FEA requirements in the pipeline and are willing to pay fairly for quality work, so long-term collaboration is possible. read less
We are looking for an experienced FEA engineer to perform structural analysis on a simple pipe assembly made of mild steel (yield ≈ 250 MPa).
Assembly Details :
1. Handle Pipe (Hollow)
- Outer Diameter: 40 mm
- Length: 1000 mm
2. Weight Plates
- Total mass: ~20 kg
- Clamped directly to the end of the handle pipe
- Mounted using two cylindrical pins (one at the
top and one at the bottom)
- Approximate stack height: 120 mm
Analysis Requirements – Phase 1
1. Evaluate stresses and deflections under:
- Self-weight
- Swinging conditions at 1 RPM, considering
centrifugal forces of 20 kg at a 0.9 m radius
- Force due to sudden stop during swings, treated
as the resultant of the momentum of the weight
plate (a sudden-stop load, not an impact)
2. Use bonded contacts and bolt/pin connectors
(simplified setup acceptable)
Deliverables
1. Minimum required wall thickness of the handle
pipe
2. Minimum required pin and hole diameters
3. Stress and deflection plots, including safety
factors
4. Consideration of forces due to sudden stop
during swings
5. Final PDF report and editable FEA source file
When Applying, Please Include
1. Estimated cost and lead time for Phase 1
2. Example screenshots or reports from similar FEA
projects
3. The software you’ll use (e.g., ANSYS, SolidWorks
Simulation, Fusion 360, Abaqus, etc.) and
confirmation that it supports bolt/pin connectors
4. Number of revisions included
5. Confirmation that you will provide:
Editable FEA source file
Final PDF report
Additional Notes
We have additional FEA requirements in the pipeline and are willing to pay fairly for quality work, so long-term collaboration is possible. read less
FEA of Mild Steel Pipe Assembly (Swinging and Static Load Analysis – Phase 1)
We are looking for an experienced FEA engineer to perform structural analysis on a simple pipe assembly made of mild steel (yield ≈ 250 MPa).
Assembly Details :
1. Handle Pipe (Hollow)
- Outer Diameter: 40 mm
- Length: 1000 mm
2. Weight Plates
- Total mass: ~20 kg
- Clamped directly to the end o... read more
We are looking for an experienced FEA engineer to perform structural analysis on a simple pipe assembly made of mild steel (yield ≈ 250 MPa).
Assembly Details :
1. Handle Pipe (Hollow)
- Outer Diameter: 40 mm
- Length: 1000 mm
2. Weight Plates
- Total mass: ~20 kg
- Clamped directly to the end o... read more
FEA of Mild Steel Pipe Assembly (Swinging and Static Load Analysis – Phase 1)
We are looking for an experienced FEA engineer to perform structural analysis on a simple pipe assembly made of mild steel (yield ≈ 250 MPa).
Assembly Details :
1. Handle Pipe (Hollow)
- Outer Diameter: 40 mm
- Length: 1000 mm
2. Weight Plates
- Total mass: ~20 kg
- Clamped directly to the end of the handle pipe
- Mounted using two cylindrical pins (one at the
top and one at the bottom)
- Approximate stack height: 120 mm
Analysis Requirements – Phase 1
1. Evaluate stresses and deflections under:
- Self-weight
- Swinging conditions at 1 RPM, considering
centrifugal forces of 20 kg at a 0.9 m radius
- Force due to sudden stop during swings, treated
as the resultant of the momentum of the weight
plate (a sudden-stop load, not an impact)
2. Use bonded contacts and bolt/pin connectors
(simplified setup acceptable)
Deliverables
1. Minimum required wall thickness of the handle
pipe
2. Minimum required pin and hole diameters
3. Stress and deflection plots, including safety
factors
4. Consideration of forces due to sudden stop
during swings
5. Final PDF report and editable FEA source file
When Applying, Please Include
1. Estimated cost and lead time for Phase 1
2. Example screenshots or reports from similar FEA
projects
3. The software you’ll use (e.g., ANSYS, SolidWorks
Simulation, Fusion 360, Abaqus, etc.) and
confirmation that it supports bolt/pin connectors
4. Number of revisions included
5. Confirmation that you will provide:
Editable FEA source file
Final PDF report
Additional Notes
We have additional FEA requirements in the pipeline and are willing to pay fairly for quality work, so long-term collaboration is possible. read less
We are looking for an experienced FEA engineer to perform structural analysis on a simple pipe assembly made of mild steel (yield ≈ 250 MPa).
Assembly Details :
1. Handle Pipe (Hollow)
- Outer Diameter: 40 mm
- Length: 1000 mm
2. Weight Plates
- Total mass: ~20 kg
- Clamped directly to the end of the handle pipe
- Mounted using two cylindrical pins (one at the
top and one at the bottom)
- Approximate stack height: 120 mm
Analysis Requirements – Phase 1
1. Evaluate stresses and deflections under:
- Self-weight
- Swinging conditions at 1 RPM, considering
centrifugal forces of 20 kg at a 0.9 m radius
- Force due to sudden stop during swings, treated
as the resultant of the momentum of the weight
plate (a sudden-stop load, not an impact)
2. Use bonded contacts and bolt/pin connectors
(simplified setup acceptable)
Deliverables
1. Minimum required wall thickness of the handle
pipe
2. Minimum required pin and hole diameters
3. Stress and deflection plots, including safety
factors
4. Consideration of forces due to sudden stop
during swings
5. Final PDF report and editable FEA source file
When Applying, Please Include
1. Estimated cost and lead time for Phase 1
2. Example screenshots or reports from similar FEA
projects
3. The software you’ll use (e.g., ANSYS, SolidWorks
Simulation, Fusion 360, Abaqus, etc.) and
confirmation that it supports bolt/pin connectors
4. Number of revisions included
5. Confirmation that you will provide:
Editable FEA source file
Final PDF report
Additional Notes
We have additional FEA requirements in the pipeline and are willing to pay fairly for quality work, so long-term collaboration is possible. read less
Things to know
Intermediate
Skill Level
$80
Fixed-rate (USD)
Part-time
Job type
Under 1-month
Job duration
Areas of expertise
ANSYS
ANSYS FEA
FEA
FEA & Structural Analysis
Finite Element Analysis (FEA)
Finite Element Simulation
+3 more
Job categories
FEA Finite Element Analysis
About the client
Payment ready
India (08:32 am)
Posted
Active
Job activity
22 Applicants
0 interviews in progress
Similar jobs
Simple structural FEM analysis (load on a frame)
Remote - Posted
Please see the attached PDF and step file. The instructions are available in the PDF, while the model is available in the .step file.
FEA Finite Element Analysis
Structural Engineering
3D Design Services
View job
A320 Landing gear simulation (kinematics simulation)
Remote - Posted
Hi, can you do simulation of landing gear A320 using msc adams and its for today.
FEA Finite Element Analysis
Aerospace Engineering
Mechanical Engineering
View job
nonlinear FEA simulation
Remote - Posted
i need a detailed simulation based on the drawings that are attached
FEA Finite Element Analysis
3D Design Services
3D Modeling
View job
FEA Landing Gear
Remote - Posted
I have designed a landing gear system for an aircraft. What I would like to do is see how strong it is and identify weak areas or areas I can optimize for weight savings. The...
FEA Finite Element Analysis
3D Design Services
3D Modeling
View job
Nonlinear FEA simulation of rubber seal in motion
Remote - Posted
we are looking for an experienced FEA engineer with expertise in elastomer seals, nonlinear contact analysis, Abaqus or Ansys
FEA Finite Element Analysis
Product Engineering Services
Mechanical Design Services
View job
CFD Engineer Needed (STAR-CCM+ / ANSYS Fluent)
Remote - Posted
We are seeking an experienced CFD Engineer with strong expertise in Siemens gas turbine thermal analysis and heat transfer simulations.
Requirements
Proven experience usin...
Mechanical Engineering
Computational Fluid Dynamics
FEA Finite Element Analysis
View job
How it works
Find hourly jobs
Top rated experts are regularly hired for hourly jobs & ongoing client work.
Fixed-rate jobs
Experts can browse & apply to fixed-rate work & quote on a flat-rate basis.
Design contests
Experts build a reputation and earn prizes by participating in design challenges.
About Cad Crowd
4.9/5.0
(Our client satisfaction)
G2 2022
Spring high performer
203,329
global members
33,295
projects delivered to clients
Trusted by
