Remote
Work location
Correction of Breathalyzer Module (PCB) & Finalization of Vehicle Telematics Kit Ended
About the job
I am developing an embedded telematics system for vehicles based on a Raspberry Pi Zero 2 W.
The main kit already integrates multiple modules (accelerometer/gyroscope, GPS, humidity/temperature sensor, camera, OBD-II via UART, 4G SIM7600G-H, OLED SSD1309, NFC MFRC522, LiFePO4 battery with solar charging). It is designed for advanced telematics: driving data logging, fatigue detection via camera, and cloud connectivity.
A detachable personal breathalyzer module has also been designed (Figaro TGS822 + ADS1115 + ATtiny1614 + LEDs + buzzer + pogo pins). Each driver connects their module, performs the test, and the data is automatically sent to the kit.
I have already completed the routing of the breathalyzer module and most of the main kit. I now need a freelancer to:
Review and correct the breathalyzer PCB (schematic, routing, ATtiny programming, pogo pin/power integration).
Finalize the main kit PCB (check routing, ensure correct integration of all modules, and verify power supply reliability: USB-C + LiFePO4 + TP4056/TP5000).
Suggest improvements for component placement to make integration into a custom enclosure easier.
I work with Proteus and would prefer to continue with it. Current design files (schematic, PCB, BOM, sketches) will be provided.
Looking for an experienced PCB designer/embedded engineer available to finalize this project within a short timeframe.
The main kit already integrates multiple modules (accelerometer/gyroscope, GPS, humidity/temperature sensor, camera, OBD-II via UART, 4G SIM7600G-H, OLED SSD1309, NFC MFRC522, LiFePO4 battery with solar charging). It is designed for advanced telematics: driving data logging, fatigue detection via camera, and cloud connectivity.
A detachable personal breathalyzer module has also been designed (Figaro TGS822 + ADS1115 + ATtiny1614 + LEDs + buzzer + pogo pins). Each driver connects their module, performs the test, and the data is automatically sent to the kit.
I have already completed the routing of the breathalyzer module and most of the main kit. I now need a freelancer to:
Review and correct the breathalyzer PCB (schematic, routing, ATtiny programming, pogo pin/power integration).
Finalize the main kit PCB (check routing, ensure correct integration of all modules, and verify power supply reliability: USB-C + LiFePO4 + TP4056/TP5000).
Suggest improvements for component placement to make integration into a custom enclosure easier.
I work with Proteus and would prefer to continue with it. Current design files (schematic, PCB, BOM, sketches) will be provided.
Looking for an experienced PCB designer/embedded engineer available to finalize this project within a short timeframe.
I am developing an embedded telematics system for vehicles based on a Raspberry Pi Zero 2 W.
The main kit already integrates multiple modules (accelerometer/gyroscope, GPS, humidity/temperature sensor, camera, OBD-II via UART, 4G SIM7600G-H, OLED SSD1309, NFC MFRC522, LiFePO4 battery with solar charging). It is designed for advanced telematics: driving data logging, fatigue detection via camera, and cloud connectivity.
A detachable personal breathalyzer module has also been designed (Figaro TGS822 + ADS1115 + ATtiny1614 + LEDs + buzzer + pogo pins). Each driver connects their module, performs the test, and the data is automatically sent to the kit.
I have already completed the routing of the breathalyzer module and most of the main kit. I now need a freelancer to:
Review and correct the breathalyzer PCB (schematic, routing, ATtiny programming, pogo pin/power integration).
Finalize the main kit PCB (check routing, ensure correct integration of all modules, and verify power supply reliability: USB-C + LiFePO4 + TP4056/TP5000).
Suggest improvements for component placement to make integration into a custom enclosure easier.
I work with Proteus and would prefer to continue with it. Current design files (schematic, PCB, BOM, sketches) will be provided.
Looking for an experienced PCB designer/embedded engineer available to finalize this project within a short timeframe.
The main kit already integrates multiple modules (accelerometer/gyroscope, GPS, humidity/temperature sensor, camera, OBD-II via UART, 4G SIM7600G-H, OLED SSD1309, NFC MFRC522, LiFePO4 battery with solar charging). It is designed for advanced telematics: driving data logging, fatigue detection via camera, and cloud connectivity.
A detachable personal breathalyzer module has also been designed (Figaro TGS822 + ADS1115 + ATtiny1614 + LEDs + buzzer + pogo pins). Each driver connects their module, performs the test, and the data is automatically sent to the kit.
I have already completed the routing of the breathalyzer module and most of the main kit. I now need a freelancer to:
Review and correct the breathalyzer PCB (schematic, routing, ATtiny programming, pogo pin/power integration).
Finalize the main kit PCB (check routing, ensure correct integration of all modules, and verify power supply reliability: USB-C + LiFePO4 + TP4056/TP5000).
Suggest improvements for component placement to make integration into a custom enclosure easier.
I work with Proteus and would prefer to continue with it. Current design files (schematic, PCB, BOM, sketches) will be provided.
Looking for an experienced PCB designer/embedded engineer available to finalize this project within a short timeframe.
I am developing an embedded telematics system for vehicles based on a Raspberry Pi Zero 2 W.
The main kit already integrates multiple modules (accelerometer/gyroscope, GPS, humidity/temperature sensor, camera, OBD-II via UART, 4G SIM7600G-H, OLED SSD1309, NFC MFRC522, LiFePO4 battery with solar charging). It is designed for advanced telematics: driving data logging, fatigue detection via camera,... read more
The main kit already integrates multiple modules (accelerometer/gyroscope, GPS, humidity/temperature sensor, camera, OBD-II via UART, 4G SIM7600G-H, OLED SSD1309, NFC MFRC522, LiFePO4 battery with solar charging). It is designed for advanced telematics: driving data logging, fatigue detection via camera,... read more
I am developing an embedded telematics system for vehicles based on a Raspberry Pi Zero 2 W.
The main kit already integrates multiple modules (accelerometer/gyroscope, GPS, humidity/temperature sensor, camera, OBD-II via UART, 4G SIM7600G-H, OLED SSD1309, NFC MFRC522, LiFePO4 battery with solar charging). It is designed for advanced telematics: driving data logging, fatigue detection via camera, and cloud connectivity.
A detachable personal breathalyzer module has also been designed (Figaro TGS822 + ADS1115 + ATtiny1614 + LEDs + buzzer + pogo pins). Each driver connects their module, performs the test, and the data is automatically sent to the kit.
I have already completed the routing of the breathalyzer module and most of the main kit. I now need a freelancer to:
Review and correct the breathalyzer PCB (schematic, routing, ATtiny programming, pogo pin/power integration).
Finalize the main kit PCB (check routing, ensure correct integration of all modules, and verify power supply reliability: USB-C + LiFePO4 + TP4056/TP5000).
Suggest improvements for component placement to make integration into a custom enclosure easier.
I work with Proteus and would prefer to continue with it. Current design files (schematic, PCB, BOM, sketches) will be provided.
Looking for an experienced PCB designer/embedded engineer available to finalize this project within a short timeframe. read less
The main kit already integrates multiple modules (accelerometer/gyroscope, GPS, humidity/temperature sensor, camera, OBD-II via UART, 4G SIM7600G-H, OLED SSD1309, NFC MFRC522, LiFePO4 battery with solar charging). It is designed for advanced telematics: driving data logging, fatigue detection via camera, and cloud connectivity.
A detachable personal breathalyzer module has also been designed (Figaro TGS822 + ADS1115 + ATtiny1614 + LEDs + buzzer + pogo pins). Each driver connects their module, performs the test, and the data is automatically sent to the kit.
I have already completed the routing of the breathalyzer module and most of the main kit. I now need a freelancer to:
Review and correct the breathalyzer PCB (schematic, routing, ATtiny programming, pogo pin/power integration).
Finalize the main kit PCB (check routing, ensure correct integration of all modules, and verify power supply reliability: USB-C + LiFePO4 + TP4056/TP5000).
Suggest improvements for component placement to make integration into a custom enclosure easier.
I work with Proteus and would prefer to continue with it. Current design files (schematic, PCB, BOM, sketches) will be provided.
Looking for an experienced PCB designer/embedded engineer available to finalize this project within a short timeframe. read less
Things to know
Expert
Skill Level
Open budget
Fixed-rate
Part-time
Job type
Under 1-month
Job duration
Areas of expertise
Circuit Design
Embedded Systems Engineering
PCB Layout Design
Power Supply Design
Prototyping
Schematic Capture
+3 more
Job categories
Electronic Prototyping and Design Services
Electronics Design Service
About the client
Payment ready
France (10:14 pm)
Posted
Active
Job activity
14 Applicants
2 interviews in progress
Similar jobs
KiCad Hardware Design from Requirements – ESP32-S2 USB-C / USB Host / RS232 Board for JLCPCB PCBA
Remote - Posted
Project title:
KiCad Hardware Design from Requirements – ESP32-S2 USB-C / USB Host / RS232 Board for JLCPCB PCBA
Project description:
We need an electronics / PCB desig...
Electronic Prototyping and Design Services
Electronics Design Service
Electrical Circuit Design Services
Electronic Devices
DFM Services
View job
ESP32-C3 Smart Water Tank System PCB Design
Remote - Posted
Smart Water Tank System – MAIN PCB Design
I am developing a Smart Water Tank System and I am looking for an experienced hardware engineer to design a professional PCB for m...
PCB Design Services
Electronics Design Service
3D Modeling
View job
Circuit/PCB design.
Remote - Posted
I have a simple project, combined from retail parts, i need to create a PCB, that will recreate functionality.
Its a simple XT60 male, Voltmeter, 2 POE devices, 2POE injec...
Electrical Engineering
PCB Design Services
Electronics Design Service
Electrical Circuit Design Services
Electronic Devices
View job
CAD and electronics for Smart Pill Dispenser (Prototype Stage)
Remote - Posted
Project overview
- Developing a smart electronically controlled weekly medication dispenser targeting elderly and NDIS-eligible users. I am seeking an experienced embedded sy...
Mechanical Design Services
Prototype Design Services
Electronics Design Service
View job
PCP designing
Remote - Posted
Need to design PCP for LED light model... And it customised
PCB Design Services
Electronics Design Service
3D Modeling
View job
Custom electronic device prototype
Remote - Posted
I designed an electronics device on a breadboard, and would like to turn that into a custom pcb first and batch manufacturing.
Industrial Design Services
Product Engineering Services
Electronic Prototyping and Design Services
Electronics Design Service
Electronic Devices
View job
How it works
Find hourly jobs
Top rated experts are regularly hired for hourly jobs & ongoing client work.
Fixed-rate jobs
Experts can browse & apply to fixed-rate work & quote on a flat-rate basis.
Design contests
Experts build a reputation and earn prizes by participating in design challenges.
About Cad Crowd
4.9/5.0
(Our client satisfaction)
G2 2022
Spring high performer
198,415
global members
32,966
projects delivered to clients
Trusted by
