Remote
Work location
Gas mixing vessel Ended
About the job
We are looking for a vertical mixing vessel that will allow for up mixing co2 (and other gases in the future) up to pressures of 10 bar. Can you aid us with creating an appropriate vessel?
We would preferably have enough volume to create a batch of co2 charged water for 60-minute-long experiments (based on the flow rate range of water we pull out, seen below). However, at a minimum we need to be able to run continuous experiments for 30 minutes.
Vertical Mixing Vessel Design Specs
Material: 316L stainless steel
Working Volume: 250–500 L
Design Pressure: 10 bar
Orientation: Vertical cylinder with domed top and bottom
Mounting: Skid or frame-mounted for stability
Flow Rate Range: 0.1–0.3 L/s
Top Head Ports Needed
Gas Inlet Port – DN15
Pressure Relief Valve / Burst Disk
Pressure Gauge
Agitator or Stirrer Mount
Vent Port for depressurizing
Sidewall Ports
pH / EC Probe Port
Mounted at mid-height
Compression fitting or tri-clamp sanitary adapter
Sample Port -at mid or bottom height
Level Indicator
Bottom Ports
Water Inlet Port
3/4" BSP
isolation valve
Drain / Discharge Valve
Full-port ball valve
If possible, we also would like to have an additional port for a 3/4 “ nanobubbler BSP apparatus that we have already purchased.
We would preferably have enough volume to create a batch of co2 charged water for 60-minute-long experiments (based on the flow rate range of water we pull out, seen below). However, at a minimum we need to be able to run continuous experiments for 30 minutes.
Vertical Mixing Vessel Design Specs
Material: 316L stainless steel
Working Volume: 250–500 L
Design Pressure: 10 bar
Orientation: Vertical cylinder with domed top and bottom
Mounting: Skid or frame-mounted for stability
Flow Rate Range: 0.1–0.3 L/s
Top Head Ports Needed
Gas Inlet Port – DN15
Pressure Relief Valve / Burst Disk
Pressure Gauge
Agitator or Stirrer Mount
Vent Port for depressurizing
Sidewall Ports
pH / EC Probe Port
Mounted at mid-height
Compression fitting or tri-clamp sanitary adapter
Sample Port -at mid or bottom height
Level Indicator
Bottom Ports
Water Inlet Port
3/4" BSP
isolation valve
Drain / Discharge Valve
Full-port ball valve
If possible, we also would like to have an additional port for a 3/4 “ nanobubbler BSP apparatus that we have already purchased.
We are looking for a vertical mixing vessel that will allow for up mixing co2 (and other gases in the future) up to pressures of 10 bar. Can you aid us with creating an appropriate vessel?
We would preferably have enough volume to create a batch of co2 charged water for 60-minute-long experiments (based on the flow rate range of water we pull out, seen below). However, at a minimum we need to be able to run continuous experiments for 30 minutes.
Vertical Mixing Vessel Design Specs
Material: 316L stainless steel
Working Volume: 250–500 L
Design Pressure: 10 bar
Orientation: Vertical cylinder with domed top and bottom
Mounting: Skid or frame-mounted for stability
Flow Rate Range: 0.1–0.3 L/s
Top Head Ports Needed
Gas Inlet Port – DN15
Pressure Relief Valve / Burst Disk
Pressure Gauge
Agitator or Stirrer Mount
Vent Port for depressurizing
Sidewall Ports
pH / EC Probe Port
Mounted at mid-height
Compression fitting or tri-clamp sanitary adapter
Sample Port -at mid or bottom height
Level Indicator
Bottom Ports
Water Inlet Port
3/4" BSP
isolation valve
Drain / Discharge Valve
Full-port ball valve
If possible, we also would like to have an additional port for a 3/4 “ nanobubbler BSP apparatus that we have already purchased.
We would preferably have enough volume to create a batch of co2 charged water for 60-minute-long experiments (based on the flow rate range of water we pull out, seen below). However, at a minimum we need to be able to run continuous experiments for 30 minutes.
Vertical Mixing Vessel Design Specs
Material: 316L stainless steel
Working Volume: 250–500 L
Design Pressure: 10 bar
Orientation: Vertical cylinder with domed top and bottom
Mounting: Skid or frame-mounted for stability
Flow Rate Range: 0.1–0.3 L/s
Top Head Ports Needed
Gas Inlet Port – DN15
Pressure Relief Valve / Burst Disk
Pressure Gauge
Agitator or Stirrer Mount
Vent Port for depressurizing
Sidewall Ports
pH / EC Probe Port
Mounted at mid-height
Compression fitting or tri-clamp sanitary adapter
Sample Port -at mid or bottom height
Level Indicator
Bottom Ports
Water Inlet Port
3/4" BSP
isolation valve
Drain / Discharge Valve
Full-port ball valve
If possible, we also would like to have an additional port for a 3/4 “ nanobubbler BSP apparatus that we have already purchased.
We are looking for a vertical mixing vessel that will allow for up mixing co2 (and other gases in the future) up to pressures of 10 bar. Can you aid us with creating an appropriate vessel?
We would preferably have enough volume to create a batch of co2 charged water for 60-minute-long experiments (based on the flow rate range of water we pull out, seen below). However, at a minimum we need to be... read more
We would preferably have enough volume to create a batch of co2 charged water for 60-minute-long experiments (based on the flow rate range of water we pull out, seen below). However, at a minimum we need to be... read more
We are looking for a vertical mixing vessel that will allow for up mixing co2 (and other gases in the future) up to pressures of 10 bar. Can you aid us with creating an appropriate vessel?
We would preferably have enough volume to create a batch of co2 charged water for 60-minute-long experiments (based on the flow rate range of water we pull out, seen below). However, at a minimum we need to be able to run continuous experiments for 30 minutes.
Vertical Mixing Vessel Design Specs
Material: 316L stainless steel
Working Volume: 250–500 L
Design Pressure: 10 bar
Orientation: Vertical cylinder with domed top and bottom
Mounting: Skid or frame-mounted for stability
Flow Rate Range: 0.1–0.3 L/s
Top Head Ports Needed
Gas Inlet Port – DN15
Pressure Relief Valve / Burst Disk
Pressure Gauge
Agitator or Stirrer Mount
Vent Port for depressurizing
Sidewall Ports
pH / EC Probe Port
Mounted at mid-height
Compression fitting or tri-clamp sanitary adapter
Sample Port -at mid or bottom height
Level Indicator
Bottom Ports
Water Inlet Port
3/4" BSP
isolation valve
Drain / Discharge Valve
Full-port ball valve
If possible, we also would like to have an additional port for a 3/4 “ nanobubbler BSP apparatus that we have already purchased. read less
We would preferably have enough volume to create a batch of co2 charged water for 60-minute-long experiments (based on the flow rate range of water we pull out, seen below). However, at a minimum we need to be able to run continuous experiments for 30 minutes.
Vertical Mixing Vessel Design Specs
Material: 316L stainless steel
Working Volume: 250–500 L
Design Pressure: 10 bar
Orientation: Vertical cylinder with domed top and bottom
Mounting: Skid or frame-mounted for stability
Flow Rate Range: 0.1–0.3 L/s
Top Head Ports Needed
Gas Inlet Port – DN15
Pressure Relief Valve / Burst Disk
Pressure Gauge
Agitator or Stirrer Mount
Vent Port for depressurizing
Sidewall Ports
pH / EC Probe Port
Mounted at mid-height
Compression fitting or tri-clamp sanitary adapter
Sample Port -at mid or bottom height
Level Indicator
Bottom Ports
Water Inlet Port
3/4" BSP
isolation valve
Drain / Discharge Valve
Full-port ball valve
If possible, we also would like to have an additional port for a 3/4 “ nanobubbler BSP apparatus that we have already purchased. read less
Things to know
Intermediate
Skill Level
Open budget
Hourly
Part-time
Job type
Under 1-month
Job duration
Areas of expertise
2D & 3D CAD Design
2D & 3D Engineering Design
Job categories
Mechanical Engineering
Fabrication Drawings Services
Prototype Design Services
Mechanical Design Services
+1 more
About the client
Payment ready
Iceland (02:16 pm)
Posted
Active
Job activity
20 Applicants
2 interviews in progress
1 unanswered invites
Similar jobs
Engineers / Associate Engineers / Senior Engineering Technicians – Semiconductor Capital Equipment ((Singaporeans, PRs and LTVP holders preferred))
Singapore - Posted
Job Summary
STEMP Solutions is looking for Engineers / Associate Engineers or Senior Engineering Technicians to support semiconductor capital equipment manufacturing engineer...
Mechanical Engineering
Manufacturing Drawings
Machine Design
View job
CNC Machine Shops Needed – Real Production Machining Data (Fusion 360 CAM)
Remote - Posted
We are looking for CNC machine shops and authorized manufacturing data suppliers who can provide original files from real, previously completed 3-axis CNC milling jobs using A...
Mechanical Design Services
Manufacturing Drawings
CNC Programming
View job
Remote Mechanical Draftsman for Pressure vessels
Remote - Posted
I am looking for a Mechanical Draftsman to work in an international Project in the oil & gas sector, The candidate should have the capabilities and expertise to Draft 2D Engin...
Mechanical CAD Design
Mechanical Drafting
Mechanical Drawing Services
Mechanical Engineering
Oil & Gas
View job
Industrial or Mechanical Designer needed for Haunted House Advent Calendar Design and Prototype
Remote - Posted
Hi there!
I'm looking for an experienced mechanical or product designer to help transform a series of concept images into a fully developed, manufacturable 3D design for a...
Mechanical Design Services
Industrial Design Services
3D Architectural Modeling
Prototype Design Services
Product Engineering Services
View job
Lightsport aircraft
Remote - Posted
PROJECT TITLE:
CAD Engineering Specialist Required: 600kg Microlight Adaptation of Ercoupe 415-C/D Blueprints
PROJECT OVERVIEW:
I am scratch-building a modern 3-axis microl...
CAD Conversion Services
Aerospace Engineering
Mechanical Design Services
Design Engineering Services
View job
Designer for manufacturing unit
Remote - Posted
Design for pump agigator and pretreatment skid need 2d and 3d design in solid work and autocad
Mechanical Design Services
Product Engineering Services
3D Design Services
View job
How it works
Find hourly jobs
Top rated experts are regularly hired for hourly jobs & ongoing client work.
Fixed-rate jobs
Experts can browse & apply to fixed-rate work & quote on a flat-rate basis.
Design contests
Experts build a reputation and earn prizes by participating in design challenges.
About Cad Crowd
4.9/5.0
(Our client satisfaction)
G2 2022
Spring high performer
216,616
global members
33,568
projects delivered to clients
Trusted by
