Remote
Work location
FEA analysis of motorcycle helmet Ended
About the job
We are looking for an expert in the field to perform FEA analysis of our finished motorcycle helmet design. The content of the project is given below.
Please quote only for the entire project, not hourly.
Summary of Key Aspects for FEA (Impact) Analysis of Motorcycle Helmets:
Impact Loads: Include the speed (20-80 km/h), angle (frontal, lateral, rear), and impact points (top, side, chin).
Contact Conditions: Model the impact against surfaces like asphalt or concrete, and simulate realistic friction and sliding behaviors between the helmet and the surface.
Materials: Specify materials such as polycarbonate, fiberglass, or carbon composites, including properties like elastic modulus, impact resistance, and behavior under dynamic loads. Also consider the inner foam (EPS).
Real-World Simulation: Factor in ambient temperature and the behavior of the helmet on different surfaces, simulating its performance under dynamic loads.
Mesh: Use a refined mesh, especially in areas with high deformation, ensuring adequate density to represent the geometry accurately.
Required Results: Include stress/strain distribution, potential failure points, absorbed energy, displacement values, and effectiveness in mitigating the impact.
Iterations and Optimization: If initial results are unsatisfactory, iterate and optimize the design (reinforcements, foam adjustments) to improve performance.
Delivery Timeline: Specify the time for completing the analysis, e.g., [X we... read more
Please quote only for the entire project, not hourly.
Summary of Key Aspects for FEA (Impact) Analysis of Motorcycle Helmets:
Impact Loads: Include the speed (20-80 km/h), angle (frontal, lateral, rear), and impact points (top, side, chin).
Contact Conditions: Model the impact against surfaces like asphalt or concrete, and simulate realistic friction and sliding behaviors between the helmet and the surface.
Materials: Specify materials such as polycarbonate, fiberglass, or carbon composites, including properties like elastic modulus, impact resistance, and behavior under dynamic loads. Also consider the inner foam (EPS).
Real-World Simulation: Factor in ambient temperature and the behavior of the helmet on different surfaces, simulating its performance under dynamic loads.
Mesh: Use a refined mesh, especially in areas with high deformation, ensuring adequate density to represent the geometry accurately.
Required Results: Include stress/strain distribution, potential failure points, absorbed energy, displacement values, and effectiveness in mitigating the impact.
Iterations and Optimization: If initial results are unsatisfactory, iterate and optimize the design (reinforcements, foam adjustments) to improve performance.
Delivery Timeline: Specify the time for completing the analysis, e.g., [X we... read more
We are looking for an expert in the field to perform FEA analysis of our finished motorcycle helmet design. The content of the project is given below.
Please quote only for the entire project, not hourly.
Summary of Key Aspects for FEA (Impact) Analysis of Motorcycle Helmets:
Impact Loads: Include the speed (20-80 km/h), angle (frontal, lateral, rear), and impact points (top, side, chin).
Contact Conditions: Model the impact against surfaces like asphalt or concrete, and simulate realistic friction and sliding behaviors between the helmet and the surface.
Materials: Specify materials such as polycarbonate, fiberglass, or carbon composites, including properties like elastic modulus, impact resistance, and behavior under dynamic loads. Also consider the inner foam (EPS).
Real-World Simulation: Factor in ambient temperature and the behavior of the helmet on different surfaces, simulating its performance under dynamic loads.
Mesh: Use a refined mesh, especially in areas with high deformation, ensuring adequate density to represent the geometry accurately.
Required Results: Include stress/strain distribution, potential failure points, absorbed energy, displacement values, and effectiveness in mitigating the impact.
Iterations and Optimization: If initial results are unsatisfactory, iterate and optimize the design (reinforcements, foam adjustments) to improve performance.
Delivery Timeline: Specify the time for completing the analysis, e.g., [X weeks], and include a detailed report with results and recommendations.
Norms and Standards: Ensure compliance with international standards like ECE 22.05, DOT FMVSS 218, and ISO 16908.
Technical Report: Provide a comprehensive report with results, visual data (charts/tables), and actionable recommendations for improving the design.
Confidentiality: A non-disclosure agreement (NDA) should be signed to protect confidential information.
Software Requirements: Use recognized FEA software like ANSYS, Abaqus, Nastran, LS-DYNA, capable of simulating nonlinear materials, contact, and large deformations. read less
Please quote only for the entire project, not hourly.
Summary of Key Aspects for FEA (Impact) Analysis of Motorcycle Helmets:
Impact Loads: Include the speed (20-80 km/h), angle (frontal, lateral, rear), and impact points (top, side, chin).
Contact Conditions: Model the impact against surfaces like asphalt or concrete, and simulate realistic friction and sliding behaviors between the helmet and the surface.
Materials: Specify materials such as polycarbonate, fiberglass, or carbon composites, including properties like elastic modulus, impact resistance, and behavior under dynamic loads. Also consider the inner foam (EPS).
Real-World Simulation: Factor in ambient temperature and the behavior of the helmet on different surfaces, simulating its performance under dynamic loads.
Mesh: Use a refined mesh, especially in areas with high deformation, ensuring adequate density to represent the geometry accurately.
Required Results: Include stress/strain distribution, potential failure points, absorbed energy, displacement values, and effectiveness in mitigating the impact.
Iterations and Optimization: If initial results are unsatisfactory, iterate and optimize the design (reinforcements, foam adjustments) to improve performance.
Delivery Timeline: Specify the time for completing the analysis, e.g., [X weeks], and include a detailed report with results and recommendations.
Norms and Standards: Ensure compliance with international standards like ECE 22.05, DOT FMVSS 218, and ISO 16908.
Technical Report: Provide a comprehensive report with results, visual data (charts/tables), and actionable recommendations for improving the design.
Confidentiality: A non-disclosure agreement (NDA) should be signed to protect confidential information.
Software Requirements: Use recognized FEA software like ANSYS, Abaqus, Nastran, LS-DYNA, capable of simulating nonlinear materials, contact, and large deformations. read less
We are looking for an expert in the field to perform FEA analysis of our finished motorcycle helmet design. The content of the project is given below.
Please quote only for the entire project, not hourly.
Summary of Key Aspects for FEA (Impact) Analysis of Motorcycle Helmets:
Impact Loads: Include the speed (20-80 km/h), angle (frontal, lateral, rear), and impact points (top, side, c... read more
Please quote only for the entire project, not hourly.
Summary of Key Aspects for FEA (Impact) Analysis of Motorcycle Helmets:
Impact Loads: Include the speed (20-80 km/h), angle (frontal, lateral, rear), and impact points (top, side, c... read more
We are looking for an expert in the field to perform FEA analysis of our finished motorcycle helmet design. The content of the project is given below.
Please quote only for the entire project, not hourly.
Summary of Key Aspects for FEA (Impact) Analysis of Motorcycle Helmets:
Impact Loads: Include the speed (20-80 km/h), angle (frontal, lateral, rear), and impact points (top, side, chin).
Contact Conditions: Model the impact against surfaces like asphalt or concrete, and simulate realistic friction and sliding behaviors between the helmet and the surface.
Materials: Specify materials such as polycarbonate, fiberglass, or carbon composites, including properties like elastic modulus, impact resistance, and behavior under dynamic loads. Also consider the inner foam (EPS).
Real-World Simulation: Factor in ambient temperature and the behavior of the helmet on different surfaces, simulating its performance under dynamic loads.
Mesh: Use a refined mesh, especially in areas with high deformation, ensuring adequate density to represent the geometry accurately.
Required Results: Include stress/strain distribution, potential failure points, absorbed energy, displacement values, and effectiveness in mitigating the impact.
Iterations and Optimization: If initial results are unsatisfactory, iterate and optimize the design (reinforcements, foam adjustments) to improve performance.
Delivery Timeline: Specify the time for completing the analysis, e.g., [X weeks], and include a detailed report with results and recommendations.
Norms and Standards: Ensure compliance with international standards like ECE 22.05, DOT FMVSS 218, and ISO 16908.
Technical Report: Provide a comprehensive report with results, visual data (charts/tables), and actionable recommendations for improving the design.
Confidentiality: A non-disclosure agreement (NDA) should be signed to protect confidential information.
Software Requirements: Use recognized FEA software like ANSYS, Abaqus, Nastran, LS-DYNA, capable of simulating nonlinear materials, contact, and large deformations. read less
Please quote only for the entire project, not hourly.
Summary of Key Aspects for FEA (Impact) Analysis of Motorcycle Helmets:
Impact Loads: Include the speed (20-80 km/h), angle (frontal, lateral, rear), and impact points (top, side, chin).
Contact Conditions: Model the impact against surfaces like asphalt or concrete, and simulate realistic friction and sliding behaviors between the helmet and the surface.
Materials: Specify materials such as polycarbonate, fiberglass, or carbon composites, including properties like elastic modulus, impact resistance, and behavior under dynamic loads. Also consider the inner foam (EPS).
Real-World Simulation: Factor in ambient temperature and the behavior of the helmet on different surfaces, simulating its performance under dynamic loads.
Mesh: Use a refined mesh, especially in areas with high deformation, ensuring adequate density to represent the geometry accurately.
Required Results: Include stress/strain distribution, potential failure points, absorbed energy, displacement values, and effectiveness in mitigating the impact.
Iterations and Optimization: If initial results are unsatisfactory, iterate and optimize the design (reinforcements, foam adjustments) to improve performance.
Delivery Timeline: Specify the time for completing the analysis, e.g., [X weeks], and include a detailed report with results and recommendations.
Norms and Standards: Ensure compliance with international standards like ECE 22.05, DOT FMVSS 218, and ISO 16908.
Technical Report: Provide a comprehensive report with results, visual data (charts/tables), and actionable recommendations for improving the design.
Confidentiality: A non-disclosure agreement (NDA) should be signed to protect confidential information.
Software Requirements: Use recognized FEA software like ANSYS, Abaqus, Nastran, LS-DYNA, capable of simulating nonlinear materials, contact, and large deformations. read less
Things to know
Intermediate
Skill Level
$500
Fixed-rate (USD)
Part-time
Job type
Under 1-month
Job duration
Areas of expertise
ABAQUS
ANSYS
ANSYS FEA
Abaqus
Ansys
Finite Element Analysis (FEA)
NASTRAN
+4 more
Job categories
FEA Finite Element Analysis
Prototype Design Engineering
About the client
Payment ready
Turkey (01:31 am)
Posted
Active
Job activity
17 Applicants
0 interviews in progress
1 unanswered invites
More open jobs from this client (1)
FEA testing services
Remote - Posted
We are designing a motorcycle helmet for which an FEA analysis is required in the near future. Details on the subject are given below.
Summary of Key Aspects for FEA (Impa...
FEA Finite Element Analysis
View job
Similar jobs
Long-term Mechanical Interface Engineer (CAD + Materials + DFM + Durability) — Pickleball Paddle Prototype
Remote - Posted
I’m hiring a long-term, hourly mechanical CAD / mechanical design engineer to act like a fractional CAD/ME lead for a modular pickleball paddle. This is not a one-time modelin...
Mechanical Engineering
Prototype Design Engineering
Mechanical CAD Design
Assembly Drawing Services
Design for Manufacturing and Assembly
View job
Mechanical CAD Engineer (Hourly, Long-Term) – Pickleball Paddle Prototype
Remote - Posted
I’m looking to hire a long-term, hourly mechanical CAD engineer to act like a fractional CAD/ME lead for a consumer product mechanism/interface. This is not a one-time modelin...
Mechanical Engineering
Prototype Design Engineering
SolidWorks Engineering Services
Mechanical CAD Design
Assembly Drawing Services
View job
COMSOL Multiphysics Simulation – Evaporation & Dynamic Meniscus Formation in Capillary Tube
Remote - Posted
Project Description:
I am looking for a COMSOL expert (chemical engineer / physicist) to simulate evaporation of liquid inside a vertical capillary tube using COMSOL Multiphy...
Mechanical Engineering
FEA Finite Element Analysis
Computational Fluid Dynamics
View job
star ccm+ fsi
Remote - Posted
i will share the file and you need to identify where the problem is and how to get desired results.
Computational Fluid Dynamics
FEA Finite Element Analysis
View job
Senior Structural FEA Consultant – ANSYS Mechanical
Remote - Posted
I am commissioning a decision-critical nonlinear FEA to evaluate the structural performance of a rib-reinforced, thin-wall polymer enclosure prior to investing in injection-mo...
Mechanical Engineering
FEA Finite Element Analysis
View job
Design engineer for plastic injection moulding machine
Remote - Posted
We are looking for good experience design engineer to build up injection moulding machine. Intrested candidates can join us.
2D to 3D Modeling
3D Models of Machine Parts
FEA Finite Element Analysis
View job
