3D Modeling and Roof Design

Contest Closed
Description:
I would like an exterior and roof designed based on my floor plans. Project MUST be done in Chief Architect. Looking for a modern style home, shed roofs, similar to the contemporary home on our website www.inartifex.com/

Material can be a mix of stucco, board and batten, limit the use of stone as the home is budget conscious.

Feel free to be creative. You do not need to use the existing material etc.
Wants:
Must use Chief Architect software. Would like roof design, and exterior 3D modeling.
Software:
  1. Chief Architect

Entries

No Entries Submitted Yet.

Discussion

Sun, 22 Jun 2014 13:36:17 +0000
I can open it with Chief Architect Home Designer, but not edit it or do anything with it. Try please to save the plan into the type of this version of Chief Architect.

SabaK

Buyer

Wed, 18 Jun 2014 16:08:33 +0000
The floor plan is there, I do not need dimensions from you, just roof design and some exterior designing too. Please use Chief Architect software.
Wed, 18 Jun 2014 14:15:48 +0000
I see now the Plan.
Wed, 18 Jun 2014 14:14:50 +0000
Hello,

1- Do you want with this contest just Ideas for an exterior design of a home? oder you need also an correct dimensional design? because then i need dimensions from you.

2- Have you a plane of the rooms and walls, or i have to make the home that i like !?

3- I will work with Chief Architect Home Designer. It is O.K. ?

Similar Contests on Cad Crowd

KLEIN radio
A rugged 2-way radio without the bulk. View our current walkies at www.headsetusa.com and our rugged android phones at www.sonimtech.com. We need to design the look of a new 2-way radio to be true military spec yet not bulky with large "bumpers". Our goal is waterproof and able to be "dropped of a building" and not break apart.
KLEIN 2-Way Radio
This is a small desktop 2-way radio. Instead of having it on your hip, or a big bulky dispatch radio, this is the size of a portable radio in a desktop box.
Power SPDT Relay implemented with MOSFETS
I am currently using the following relay in a product: http://www.digikey.com/product-detail/en/te-connectivity-potter-brumfield-relays/RT424024/PB969-ND/1095293 It is a DPDT, non-latching relay rated for 8A switching, and a 24Vdc coil voltage. The problem: The "clicking sound." This is for a home audio application, so we need it to be silent. I am looking for a silent version, using MOSFETS for example, built onto a daughter board (PCB) with the same footprint and pin-out as the relay. Note - I only need SPDT capability (I tie the two poles of the DPDT relay via on the board that the relay is installed onto). One side of the relay coil (pin 1) is always tied to 24V. And the other side is either set to 24V or GND via this chip: http://www.digikey.com/product-search/en?keywords=296-19046-5-ND (which is controlled by a PIC micro) Requirements: - An electrical schematic of the new design - A BOM of all the parts required - Gerbers for the PCB daughter board - Same footprint and pin-out as the RT424024 relay. Note, for this SPDT version, the following pins will be tied together (12 & 22, 11 & 21, 14 & 24). They are already tied together on the PCB that the relay currently is soldered to. - Same 24Vdc "coil voltage" (pin 1 always tied to 24Vdc, and pin 2 is controlled externally to be 24Vdc or GND via the external chip mentioned above). - When the relay is not activated, pins 12 & 22 are connected to pins 11 & 21). When the relay is activated, pins 11 & 21 are connected to pins 14 & 24. - Use high current MOSFETs (the lower the turn on resistance, the better! Should be able to handle > 25 Amps continuously (ideally > 50 Amps continuously). - Must have full protection from ESD / over-voltage on every pin. - There must NOT be 'cross-conduction' of the pins. - Must be very reliable - Must be silent switching - Must be the same footprint and pinout as the relay that it is replacing (Mentioned above). Max. height is > 1 inch (we are only limited by the footprint, not the height). - Layout software can be whatever you want as long as I can get the PCB gerbers to send to my PCB house. - BOM should be in a spreadsheet (excel) - Electrical schematic can be in PDF
simple packaging artwork convert to packaging illustration
We make packaged product and new packaging haven't arrived for the photoshoot of the packaging for our website. We need to convert artwork of our packaging (attached) to be converted to a replica of our packaging for our website. We have 5 different flavors and need one extra illustration for all flavors lined up together. So 6 illustrations in total. Attached: 1. artwork of each flavor 2. example of how lineup of all flavors should look like
SuperSuv to be hand built for personal use
Off/On Road Super SUV, 3 seater Central driving position like a Mclaren. Rear engined, removable roof which when not in use goes over engine bay. 26 inch rims. Very clean lines. Will use donor lights (pictures included in files). Car must be dramatic with very clean simple lines. Interior must be very simple and clean lines. I have uploaded many files for inspiration. Countach for rear. Corvette for door treatment. White lotus for air vents. Diablo for roof and body lines.