Description:it is a box, come with 2 pcs 18350 batter and get a LCD dispolay to show the power capacity and alos on the box there are 3 buttons, one for switch on/off, and 2 for adjust specifications, if not 2 buttons, could be 1 pole or other design for adjust. also we need a connect on box to connect other device, it is kind of screw thread connection.
Wants:need stainless color and also AL colorful mix.size will be 30-50mm * 50-60mm * 20mm.
- Adobe Illustrator
#3 Power Box by sendil kumar
- SolidWorks 2012 — power box2 isometric view4
- SolidWorks 2012 — power box2 isometric view 3
- SolidWorks 2012 — power box2 isometric view2
- SolidWorks 2012 — power box2 isometric view1
- SolidWorks 2012 — power box2 back side view
- SolidWorks 2012 — power box2 bottom view
- SolidWorks 2012 — power box 2 top view
- SolidWorks 2012 — power box2 right side view
- SolidWorks 2012 — power box2 left side view
- SolidWorks 2012 — power box2 front view
- SolidWorks 2012 — power box1 isometric view4
- SolidWorks 2012 — power box1 isometric view3
- SolidWorks 2012 — power box1 isometric view2
- SolidWorks 2012 — power box1 isometric view1
- SolidWorks 2012 — power box1 back side view
- SolidWorks 2012 — power box1 bottom view
- SolidWorks 2012 — connector power box
- SolidWorks 2012 — power box bottom cover
- SolidWorks 2012 — power box right side panel
- SolidWorks 2012 — Power Box 1
- SolidWorks 2012 — Power Box 2
- SolidWorks 2012 — power box top cover
- SolidWorks 2012 — power box2 bottom cover
- SolidWorks 2012 — power box2 top cover
- SolidWorks 2012 — powerbox left side panel
- SolidWorks 2012 — power box1 front view
- SolidWorks 2012 — power box1 left view
- SolidWorks 2012 — power box1 right view
- SolidWorks 2012 — power box1 top view
Similar Contests on Cad Crowd
Underwater modular drone
The underwater drone is modular and autonomous. Users can assemble it from different modules fitting to each other similar to Lego pieces. Core modules are: stern with cameras and sensors, bow with propulsion system, battery, sonar, basket, a continuous robotic arm. It can work: with or without tether and recharge itself autonomously, has multiple internal navigation systems, has two independent moving cameras and lights enabling him to observe two things at the same time. The modules should be presented on the principles "Rubix cube". At this stage we are focusing on design and creativity, no need to include moving parts, they are a bonus. Must be highly visible in the water.
Modeling & Graphic Design for a Modern Landfill
We are looking for some one to design a complete landfill for use on our Tradeshow booth. We are looking for someone who can layout the entire site. From the waste cell to the roads, to the working face of the landfill and Leachate systems, liners etc. We would also like to incorporate our equipment and products into the design. This is mostly for Leachate. What we are attempting to do is show how to Waste Companies can handle their leachate to save money. There are 3 steps to this process. The first is minimization. We have developed a spray on solution that will repel water from the side slopes of the landfill and on the flat top of the landfill. Ideally we show a rain cloud raining down on the side of the landfill here and then we can have our graphic artists do bubbles on the rendering showing where that product is used. The second part we do is pre-treatment. We have designed a system that can process and clean the leachate. The leachate is pumped from the bottom of the landfill to holding tanks where we clean it from there it goes to Leachate ponds where our Evaporation Misting Equipment evaporates the water. We also have the leachate evaporated inside buildings. Ideally we want to show the daily operations of a landfill and where all of our products are used on that landfill. Visiting our website will give you a very in-depth look at what we do Attached are some samples of how landfills have been rendered in the past as well as a top view of a modern landfill in California. Also included is a aerial photo of a landfill cell being built with liner and a side view of all the layers that go into a landfill. If you have any questions or need more details please leave note This image will be blown up to fit a booth that is 5'6" high and 113" wide
(Book) 'Dragons throughout the Multiverse' Miniature design
I am a small independent self-publisher and the author/artist (Photoshop) for the Book (but that is the limitation of my design/technical expertise). This is a 3rd Printing of the book (40th Anniversary Edition) ©1982, 1994, 2022). I Need to contract with a good (possibly more competively priced) STL designer. I am going to start a Kickstarter Campagin to solicit presales for the STLs associated with this book *(and possibly do a jont-venture and/or profit share arrangemnt with the STL Designer(s) I select). (The Book has over 80+ Dragons and their included photos) *I can share samples of interior Artwork to aid in concept and STL design Anyone interested please submit a sample of the design you create based on (photo supplied below - a more simple design IMO)). Also submit a portfolio of simialr works. Thank you for your time and efforts.
Fibre Optics Installation Design Using Siemens PLM Tools
Design of Fiber Optics Cable Implementation on a 45KM Pipeline ROW Using Siemens PLM tools for CAD Design, Modelling and Process Simulation. Using Siemens SolidEdge, Technomatix Jack, TeamCenter and Into Site: Design Alignment Sheet for the 45M Pipeline and Fiber Optics Cable and render a 3D model of : Kolo creek End Facility FOC tie-in (telecoms room) The 42km Gas Pipeline with a 48 Core Aqua-Marine Fiber Optic Cable (FOC) with Uraduct Cable Protection Uraduct Cable Protection with Piggyback Clamps on the 10km swamp area Showing the 18km Land section Showing the 15km swamp Sections Showing the 7km seasonal Swamp Section Show the Splicing points for the FOC Joint boxes Show all Major and Minor river crossing Show all Major and Minor road crossing Soku End facility Tie in Well Heads to End facilities Provide as built model of the project after installation and commissioning.
The Gift Box
I'd like to have several tuck and fold boxes designed to look like elegantly wrapped gifts with nothing but the printed box and I would tie a ribbon around the box. The box in and of itself will have a glossy finish - but it should not look so much like a typical branded box - but should make the recipient feel like it is a beautiful gift. The use of simplicity and bold graphics to achieve a striking effect is key. It would be nice if the inside of the lid had a color and graphic when the user opens it. Inside the box will be a green and white marbled tissue paper (file attached). So the box needs to compliment this tissue paper and work with brand assets. I will be printing with Packlane.com so you can see how their box prints look. I have attached a sample of what a "tuck and fold" box looks like.