Powerpac Corporate Offices Design

Contest Ended, Winner(s) have been selected.
We are refitting an existing building for our corporate offices.
We are wanting to create a dynamic working environment, as well compelling corporate entrance, we want the design to look modern and also reflect our companies colours as seen on www.powerpac.co.nz
We are wanting to create a dynamic working environment, as well as a compelling corporate entrance,
We want open plan offices, as well as management offices.

We have 5 management team members, and 8 general admin, finance, sales staff.
Ask for Sample:
We would like to see some quick ideas off the attached plans we will then choose the one we like the most and go from there.


1st Winner
#2 Office - 2d part by viz_rado
2014-02-28 15:30:49
#1 Corporate office lay out by PARIKSHIT
Dear Valuable Customer,
This is Parikshit and I can do this job for you in a very innovative way. I had done part of your work & attached the files. Please look the file & give your comments for further completion of works.
Looking forward to hear from you.
2014-02-28 01:36:59


Wed, 19 Mar 2014 09:03:29 +0000
Hi John,

Which drawing would you prefer,2D or 3D.If I send you the sample work based on your drawing,is it ok .Once you accept,I can prepare complete model based on your requirements and if any changes required.Please let me know



Mon, 24 Feb 2014 00:41:57 +0000
Hello, thank you for your question.
Both if possible.



Sun, 23 Feb 2014 16:32:21 +0000
you are looking for lay out of attached files or design of office partition, furniture & its arrangement
Fri, 21 Feb 2014 14:46:47 +0000
can you please upload drawings with specific dimension, i can hardly see lines too



Tue, 18 Feb 2014 09:25:19 +0000
A 3D would be good if possible. Many Thanks.
Tue, 18 Feb 2014 04:43:17 +0000
are you simply looking for a drafted 2D version of the sketched out floor plans you provided?

Similar Contests on Cad Crowd

The Water Wheel Kayak
We are looking to blend the kayak with the pedal boat. What we want is to recreate the design thought up by Hobie Cat in which they incorporate a pedal design within the kayak. However, we want the pedals to be linked to two water wheels on the side rather than the "fin" system that Hobie Cat uses. (see photo for details) This kayak needs to incorporate a pedal system where people would normally just rest their feet. It would also have to showcase two water wheels on the side. We want the water wheels to be linked by an axe so that they may be easily removed from the kayak if the user chooses to do so. For kayak base use Prower 13 by Ocean Kayak (picture attached). The new design would have A) two pedals where one would normally rest their feet. (see Slayer 13 picture for pedal design inspiration) B) An axe with two water wheels that would be placed at the front the of kayak above the pedals but below the hatch. (See the water wheel picture for inspiration) We'd like the water wheels to be removable and not as bulky as the one in the "Water Wheel picture" What we need- 2 drawings, one from the top, one from the side (just like the slayer 13 picture)
plug pendant
Hi I am after a design of a pendant which will be gold and whole design should be raised from the base I have provided a image of a similar outcome of the technique used of raising the border and actual design which I want implemented in the new design The plug on the design should be 3 dimensional on a side perspective with the 3 pins someone how raised and the word "the" should be paved with diamonds small enough to fit 2 rows throughout
cordage cam and hook
This is to be a prototype device so it may have a few iterations. There will be additional funds for a planned phase II of this prototype. The idea is a way to secure cordage or twine. The rough specs are 40mm long, 20mm wide and 5mm thick at the base. The cam should be modeled similarly to the look of something you would see on a sailboat. The arch must be just slightly lower than the top of the cam. The cam should be usable for 2mm-6mm cordage.
A simple cad drawing for a staircase/frame for an apartment
I need a quick/simple cad drawing for a staircase in an apartment. We are replacing the staircase and frame and we wanted to put the drawing into cad with the dimensions.
17 foot Wood Drift Boat
This contest will be for the most accurate CONSTRUCTION PLANS for a WOODEN DRIFT BOAT HULL. Key features include: 5 piece hull. 5 pieces will be created separately on a table, covered in fiberglass and Kevlar, then stitched and glued together to create the shape of the hull. 1. The Bottom. (1) 3/4" Plascore (honeycomb poly material) measuring approximately 14'6" long X 60" wide. The basic shape of the bottom of this hull will be similar to a "football". However, I would like at least 4 foot STRAIGHT sections running down both sides of the hull (4 foot straight chines). This will aid in the handling of the drift boat. The 14'6" length will be lifted at both the bow and stern ends approximately 5" (rocker). Both the bow and the stern will be identical from one another, so you will only need to draw half of the boat, copy, rotate and attach to finish the plans. 2. The sides. (2) 9mm Okume plywood sides that will measure approximately 18-19 feet long and will range in height from +/-16" to 22" tall. The goal will be to create curved side panels 22" tall in the center of the boat where the oar locks will be attached for a section of at least 1 foot on either side of center. 16-18 inch middle sections for ease of entry into the boat that will gradually slope to meet, and 16" sections at the bow and stern. This should include the end angles where the sides will meet the bottom of the hull, and the bow and stern sections. Obviously all up for adjustment to get the overall shape of the hull to look correct anf for ease of construction. 3. The Bow and stern. This is the difficult part of the boat and the real reason for my contest. To create (2) conical or half-cylinder shapes from 3mm pieces of Okume Plywood that will be bent and laminated 3 times to match the side thickness. This will include the dimensions and angles for attaching that curved transom to the sides and the bottom of the Plascore panels to create an appropriate fit. 3mm Okume can be bent into about an 18" circle, so curves with a radius down to about 8" are possible depending on the grain. I have included a photo of a similar boat hull that has already been built per my design. However, this was done entirely by trial and error and cannot be duplicated. It is also smaller than the specifications in these plans. My goal is to end up with a set of plans that would allow this hull shape to be recreated. NOTE: The interior layout of the boat will be modeled in the future. Additional design work may be possible for the winner of this contest. For that reason, please include a centerline on both axis to use a measuring point for interior layout.