Parallelogram wall paper
in
CAD Design
held by
Steve D
Last seen:
December 12, 2018
Contest Ended, Winner(s) have been selected.
Description:
I am a glass artist, I need a geometric design for transfer to sandblast resist, that will be cut on my Graphtec plotter. I will be cutting this pattern 24" x 24", using Robo Cut Pro.
Wants:
Geometric consistency particularly the angles, they must be exactly 60 degrees and 120 degrees.
Software:
- dxf file for use with robo cut pro
Prepaid PrizeEntries
1st Winner
#2 Parallelogram pattern
by PETER LAKATOS
I have submited two files, one that has the 24"x24" border, and one that doesn't. Please feel free to send feedback if you need anything else done, or modified.
I made sure lines do not overlap or have gaps.
Thank you.
I made sure lines do not overlap or have gaps.
Thank you.
Jan 8, 2014 14:35
#1 Parallelogram for sand cuting in dxf format
by Antanas
Parallelograms cutting path for 24" x 24
Jan 8, 2014 14:28
#4 Parallelogram for sand cuting in dxf format
by Antanas
60° x 120° x 60° x 120° Parallelogram cutting path for 24"x24" size drawing
Jan 8, 2014 15:56
#5 wallpaper
by MRHoover
This is somewhat a sample. most machines that use .dxf dont like intersecting lines. I was assuming you want like lattice or something, but if you wanted the actual diamond shaped pieces a few changes could be made. please let me know if you want any changes.
Jan 8, 2014 17:41
#7 Parallelogram wall paper
by danby
the file design is conforms to the requirements given.I suggest to changing dimensional diamond shape to fit perfectly between the sides of the square 24
Jan 8, 2014 22:30
#9 pattern orientation - 2
by vinya
in case of doubt or correction i am to order
Thanx
Thanx
Jan 9, 2014 10:08
#10 Paralelogram_wall_paper
by viz_rado
I have put it a nc.file - file for CNC ( CAD/CAM - produced file)
Jan 9, 2014 10:55
#11 Parallelogram Wall Paper
by CADmate
DXF and DWG file attached for Graphhtec cutter/plotter
Jan 9, 2014 12:25
#12 Path lines of Sandblasting for Parallelogram
by Antanas
Only Path lines (1/4" width) of Sandblasting for Parallelogram.
Good luck!
Good luck!
Jan 9, 2014 15:59
#16 Sanblast Mask
by Three Axis
I have drawn the pattern to fit on 24" square masking material so it can be repeated in either direction
Jan 9, 2014 21:19
Discussion
hi, could you please tell me: 1. were will be the origin of your model?
2. do you want a frame on your pattern?
3. do you want the model or the toolpath?
4. if you want the toolpath what is the size of your cutting tool?
2. do you want a frame on your pattern?
3. do you want the model or the toolpath?
4. if you want the toolpath what is the size of your cutting tool?
Similar Contests on Cad Crowd
Conceptional physics design
This is a abstract design for a physics project about energy conversion using high charge density. The design is called longitudinal plasma vortex energy converter: a counter-rotating outer quartz cylinder with an internal counter-rotating epicyclic gear train with a downward facing rounded point nozzle connected to a low-pressure turbine and located where the sun gear is located. The system also contains a clockwise-rotating inner quartz cylinder with an internal clockwise-rotating epicyclic gear train with a upward facing pointed edge nozzle connected to a low-pressure turbine and located where the sun gear is located. The representation is designed to showcase a closed system in which the plasma is pushed upward by the clockwise-rotating turbine and pointed edge nozzle and then pushed downward on the sides by the counter-rotating turbine and rounded point nozzle of the outer cylinder (motion shown by green arrows). Attached please find a drawing that I want the designer to refine to the best of his/her talent.
TAF
Needing someone to design a floor plan. taking into account the needs and lifestyle of the occupants
Design my Koala Bear
I am looking for a 2.5 x 2.5 inch circular doll in the shape of Koala Bear. I want it to be geometrical and the colors to be white/grey/pink/black. I attached a quick flat 2D quick drawing that I put together but I want it in a 3D drawing and with the color scheme to match a Koala Bear. The doll should be geometric all around.
Women's ring design
Hi, I need 3D CAD step file & rendering for a silicone wedding ring that will be made from a steel ring mold.
Logo (attached) needs to be debossed on the inside & the number 7 on the opposite side inside
Please see attached images for the ring design.
Dimensions of the ring should be:
Width: 3.6mm
Thickness: 2.3mm
Inner Diameter: 17.3mm
Inner Circumference: 54.40mm
Clothing Shop Plans
i want a designer to transfer my idea to 3D plan , i want make a design for men clothes shop from outside and inside , i want inside decoration like a cave or rock wall and show the clothing stand and table and from outside the shop face all is glasses and the door in the middle with black banner for shop name "GRAY WOLF" , the shop size is 6x10 meter , please check the attachment maybe it will help you ,thank you.
markos