Description:one page 8 1/2" x 11", currently hand drawn, community is asking for one done on "Autocad".
Wants:just measurements, I can email you the hand drawn version.
No Comments Submitted Yet.
Similar Contests on Cad Crowd
I WILL DRAW YOUR DREAM HOME IN MINIMUM BUDGET
Friends, I have my own architectural company in India. I have over 19 years of experience in this field. I assure you that you will be able to do your work on time, at a lower cost. You can message me about your home and send me a site plan.
Create Professional Title Page for Building Envelope Company - AutoCAD or Chief Architect
We want a freelance designer to create a professional title page for our company. Our old title page doesn't look very good; please refer to "Peerless Old Title Page.pdf" file (please ignore drawing details). See this screencast for notes: http://bit.ly/Y7Ntwa We need the drawings produced (in imperial/metric) with these dimensions: 8"x11" (also need in metric) 11"x17" (also need in metric) 36"x24" (also need in metric) Our logo should be included on the title block. Please see the file attachments for work details and let us if you have any questions. There is a lot more upcoming work that we may ask the best contrator to help out with in the near future. Note: Ideally, the CAD software should be Chief Architect or in an AutoCAD format that can be imported into our software.
shop site plan and floor plans required ASAP
I have to submit drawings to city council ASAP for change of use of commercial property. The shop was used to be bakery. I want shop to be a retail shop. I need to fill planning permit along with 2 sets of drawings to council. 1) Old floor Plan. 2) New floor Plan.
Convert Hand Drawn Plans to CAD (trace)
I have 2 hand drawn plans of my property that need to be converted to CAD format (DWG) as well as PDF. These are approved development plans which now need to be used to show amendments for review. I have both A4 and A3 scans available of the plans. Coloured sections on plans were used for previous approved amendments that have been completed and need to be incorporated into the CAD plan.
Gallery Construction calculations
This task requires calculating which profiles to use for a gallery structure! No need to design or draw anything in this task. Only calculate. The attached plan was made by an engineer for building a gallery in my house from steel profiles but I suspect the profiles he chose are an over kill so I'd like to hear some more opinions. I assure everyone I will ultimately build the gallery under his approval. The 40 square meters gallery is to be used for 2 living rooms for my kids. It will hold normal furniture that such rooms should hold. The main beam would be HEA, IPN or another profile you may recommend for decreasing the profile height. The main beam would be made of 2 parts welded together and an RHS or IPN pillar underneath the connection point. I am not sure yet where the pillar would be, therefore I need the main beam profile calculated for 2 options: 390cm + 600cm or 270cm + 720cm. Each part of the main beam might be a different profile so please calculate the minimal required profile for each part. I would also like to know what profile measures I would need if there was to be no pillar in the middle of the main beam and it would be a one piece of 990cm. All other 3 sides of the gallery have an existing wall and part of this wall has an existing reinforced concrete belt (yellow in the drawing). There are also 4 existing reinforced concrete pillars as appears in the drawing. It is planned to have a UPN profile (welded together as one) all along the 3 other sides. The whole structure will be supported by 6 RHS pillars (the main beam middle pillar might be IPN) that will be attached with Jumbo screws and chemical adhesive to reinforced concrete floor. At the back plane of the gallery the 3 RHS pillars are very close to existing reinforced concrete pillars. Is it possible to attach the UPN to the existing pillars and make do without these 3 RHS pillars? The main beam and the back plane will be connected with 15 IPN beams. I still don't know if the length of these beams will be 429cm or 470cm so I need both options calculated. The floor surface will be made of several layers for isolation with 30mm pine wood at the top. I need to know what are the minimal measures for all the profiles in my plan and according to which assumptions the calculation was done. One last question. Above the gallery there is a 10meters wide by 8 meters long wooden shingle roof (as in the photos) that is supported by small wooden pillar in the middle. I need to install a 10meter steel beam from side to side at the middle of the roof so that I can remove the supporting wooden pillars. What would be the minimal IPN profile to use for that? Would IPN 100 or 120 do the job? Calculate the following profiles: Main IPN or HEA beam at 720cm + 270cm (2 different profiles?): Main IPN or HEA beam at 600cm + 390cm (2 different profiles?): UPN: Width IPN beams at 429cm: Width IPN beams at 470cm: RHS pillars: IPN pillar: Roof 990cm IPN beam: Any improvement suggestions are welcome.