Steel Structure for Tekla

Contest Closed
Description:
I need a Tekla model of steel structure already designed in Autocad. This modeling must contain all the details of the design sheets, but there is no need to create the design sheets again in the model.
Wants:
Accuracy of connections, right use of components.
Don't Wants:
I don't need a model with parts unconnected or with components placed incorrectly in each part of the model.
Ask for Sample:
I would like to each application create the design grid and place the sctructural columns in the right position before modeling the hole structure.
Software:
  1. Tekla Structures (21)

Entries

No Entries Submitted Yet.

Discussion

Lucian

Administrator

Tue, 08 Sep 2015 08:10:50 +0000
Dear designers,

FYI, the contest has been closed on request.

Regards,
Lucian
Wed, 02 Sep 2015 15:35:37 +0000
I have tekla 13 version... is it ok???
Mon, 24 Aug 2015 04:11:13 +0000
dear sir i am a steel structure detailer and designer have some queries to clear if possible can you drop me pm

romeuneiva

Buyer

Thu, 20 Aug 2015 18:14:22 +0000
viz_rado,
Yes, I need it to be modeled in Tekla 21.

I don't have the connection, but I can share with you the brazilian enviorement that contains components used in our construction sites. However, I rather you modeled the design according to the design sheets I sent. If is there any doubt about it, we can schedule an skype meeting to talk about it.

I don't need 2D drawings for manufacturing, I aready have them. They are the files I attached. But, I don't have the 3D model of it. This is what I realy need: a 3D Model fully detailed according to the 2D drawings I already have.
Thu, 20 Aug 2015 16:00:28 +0000
Before to speak for any price we need to know what exact the job include.
1. You want this construction to be modeling in tekla
2. Are you have all connection design already? If you dosnt have must be design by some code like eurocode
3. Do you want 2d drawing for manufactoring, like single parts drawing, assembly drawings, montage position plans?

romeuneiva

Buyer

Thu, 20 Aug 2015 10:50:39 +0000
Hello everyone, what would be the resonable price for this modeling job? I'd like to receive some proposals, then I make my offer.
Sincerely,
Thu, 20 Aug 2015 05:16:09 +0000
Hi, I can done this project. I have done a lot of steel construction on tekla structure software. You can see my portfolio - www.rema-design.com
But this price is very low for this kind of job. If you want to be done this job first the price must be change. Normal for this kind of job the lowest price price is 18 euro /hour for steel detailing for static calculation of the connection is 21 euro /hour.
Just to know.
Have a good day.
Wed, 19 Aug 2015 21:44:08 +0000
200?!
Wed, 19 Aug 2015 15:34:51 +0000
I Hope you can find a guy that work for you project!
I felt very exciting with it, until I saw the price :v!

Similar Contests on Cad Crowd

Universal Phone Mount
Hi Cad Crowd! We're in need of adjusting one of the components of our product. We have an existing 3D model that we need adjusted. We are keeping the same top and bottom connection the same. The basic design is similar to a standard universal phone mount for a car. We want to use the same mechanism as shown in the pictures and then adjust it to our requirements. The system will be 3 major components. Part 1: Back piece that has top connection and bottom connection which won't be changed much except for the width. This area will be where the gears/spring/everything sits on. Part 2: This will be the two "wing walls" that extrude left and right that will be sat on the back plate area. Part 3: Will enclose this area and have a bottom stub where the phones sit. We play on adding some little foam on the front of part 3 and on the insides of the wing walls. We think that the gear mechanism can be reduced in size and that we can flip it so that they sit above the wing walls (and in the center of the system).
By The Sea
An existing house is being renovated. We have 2D sketches which have been approved by local council. The pitched roof will be removed and replaced with a flat roof so that a roof terrace is created. This will have views of the ocean and entertaining equipment such as a BBQ and seating / lounge. The existing living area on Level 2 will be extended as shown on drawings and new internal stairs allowing access from Level 2 to the roof terrace. The kitchen, bathrooms, existing floors, lighting etc will all be replaced with new. A garage will be installed on Level 1 (ground floor entry). The house will effectively look totally different from the front with a new entrance, garage and new fa├žade.
Handle / Grip design with gear & Latch
The design needed is for a handle / grip that when squeezed, it will make a 3/8" square bar, which is in a 1 1/2" high extruded piece, travel aprox 2 1/2" towards the grip. See short video. This also needs to be able to lock into multiple positions when squeezed and also have an easy release so that when released it springs back into its original open position. This will be attached to the end of the 1 1/2" high extrusion. There are 2 openings in this extrusion. One along the top will be a square opening in which the 3/8" square bar will be encased and the other one will be a round hole which will encase a 3/8" round tube in which water will travel through. This round tube will need to extend out the back of the extrusion and through the handle and attach to a water hose. The handle / grip needs to extend up above the extrusion a minimal amount. The attached picture of my prototype extends way too high above the extrusion. One thought is to incorporate a rack and pinion type gear to achieve this. Any type of gear or mechanism will need to be enclosed in the handle.
UAV Reaper Drone
Need complete design for Reaper Drone in solid Works for each part of the stucture (Fuselage+ wings+ wheels) no need for engine and inside equipements, and i don't need rocket design and no need also for 2D drafting
Leaf Dental Care
My company is "Leaf Dental Care", and our mantra is "Eco-friendly Wellness". We will operate an eco-conscious dental clinic that treats our patient with a holistic approach. The project is to create a visual diagram of what the Reception Area and Operatory Room will look like. The Reception Area will be ~400sq ft, and have a store front with floor to ceiling windows. Theme: yoga studio, spa, Zen garden Color Scheme: White, earth tones, wood, stone. The waiting area will consist of a "retail portion", and a "reception portion" Retail Portion: There should be store front display for retail items such as organic health and beauty products. Like an "organic" Sephora. Our neighbors will be high-end retail stores, and we should blend in. Reception Portion: My logo should be displayed behind the receptionist desk. There will be organic cotton fabric couches for people to sit and wait. The kids play area will consist of wooden block toys by Melissa and Doug. LED television will be playing health educational videos. Patients can fill out medical information on tablets. Lighting will be indirect LED lighting. Ambient music will be tranquility music. All medical professionals are wearing yoga clothes instead of scrubs and lab-coats. Operatory Room Diagram: The theme is carried over to the operatory rooms.