Stainless Vacuum Distiller Chamber CAD (Countertop Size) Ended

About the job

Project Brief (What I Need Designed)
I need a simple stainless steel vacuum chamber and external coil layout for a small countertop water distiller. This is ONLY the mechanical shell and mounting points, no internal electronics or special internals.

Please design:

Main Chamber

Material: SS304

Shape: Vertical cylinder

Outer diameter: 250 mm

Height: 300 mm

Wall thickness: 2 mm

Bottom: flat, welded

Bottom plate:

4 × M6 threaded inserts arranged in a square, centered, on the inside bottom (for a removable heater plate, you just place the holes).

Bottom drain:

1 × 1/4" NPT drain port at the lowest point, oriented downwards.

Inlet (Feed Water Nozzle Port)

Location: Side wall, 80 mm above bottom (centerline).

Connection: 1/4" NPT female threaded boss welded to side wall (I will install my own spray nozzle).

Steam Outlet / Vacuum Port

Location: Top center of the lid.

Connection: 1 × 25 mm OD stub pipe, 50 mm long, vertical.

This will serve as both steam outlet and vacuum connection (to be connected to my external condenser/piping).

External Coil Mounts (Preheat Coil Around Chamber)

Around the outside of the cylinder, please add simple guides/tabs for a 1/4" copper tube coil:

4 vertical “ears” or tabs spaced at 90° around the circumference, with slots or holes so I can tie/clamp a 1/4" tube coil to the outside of the chamber.

Coil height region: from 50 mm above bottom to 250 mm (do not interfere with ports).

Top... read more
Project Brief (What I Need Designed)
I need a simple stainless steel vacuum chamber and external coil layout for a small countertop water distiller. This is ONLY the mechanical shell and mounting points, no internal electronics or special internals.

Please design:

Main Chamber

Material: SS304

Shape: Vertical cylinder

Outer diameter: 250 mm

Height: 300 mm

Wall thickness: 2 mm

Bottom: flat, welded

Bottom plate:

4 × M6 threaded inserts arranged in a square, centered, on the inside bottom (for a removable heater plate, you just place the holes).

Bottom drain:

1 × 1/4" NPT drain port at the lowest point, oriented downwards.

Inlet (Feed Water Nozzle Port)

Location: Side wall, 80 mm above bottom (centerline).

Connection: 1/4" NPT female threaded boss welded to side wall (I will install my own spray nozzle).

Steam Outlet / Vacuum Port

Location: Top center of the lid.

Connection: 1 × 25 mm OD stub pipe, 50 mm long, vertical.

This will serve as both steam outlet and vacuum connection (to be connected to my external condenser/piping).

External Coil Mounts (Preheat Coil Around Chamber)

Around the outside of the cylinder, please add simple guides/tabs for a 1/4" copper tube coil:

4 vertical “ears” or tabs spaced at 90° around the circumference, with slots or holes so I can tie/clamp a 1/4" tube coil to the outside of the chamber.

Coil height region: from 50 mm above bottom to 250 mm (do not interfere with ports).

Top Lid / Access

Design the top as a removable lid:

Either a clamped flange or bolt ring.

Include a circumferential groove or flat for an O‑ring (I will specify seal later).

Lid must seal under light vacuum (~200 mbar absolute).

Steam Path Mount in Lid

On the underside of the lid, directly under the 25 mm outlet, add:

A simple circular flat area (about 60 mm diameter) with 4× M4 through holes around it, 90° apart, on a 40 mm pitch circle.

This is for mounting my internal insert (you don’t design the insert, just the mounting pattern).

Supports / Feet

Add 3 or 4 simple short legs or base pads so the chamber stands stable on a flat surface.

Total unit height including feet: roughly 320–340 mm.

Deliverables

3D model: STEP (.step) and native file (SolidWorks / Fusion / Inventor).

2D manufacturing drawings (PDF + DWG/DXF) with all key dimensions, tolerances suitable for sheet metal/fabrication.

Exploded view or simple assembly drawing showing lid, body, and coil mounts.

Notes

Treat all internals as generic: no need to design heaters, coils, or special internals.

Design for ease of fabrication by a typical stainless steel shop.

This is for vacuum distillation, so avoid sharp internal corners where stress may concentrate; use reasonable fillets. read less
Project Brief (What I Need Designed)
I need a simple stainless steel vacuum chamber and external coil layout for a small countertop water distiller. This is ONLY the mechanical shell and mounting points, no internal electronics or special internals.

Please design:

Main Chamber

Material: SS304

Shape: Vertical cylinder

Outer diameter: 250 mm

Height: 300 mm

Wall thickness: 2 mm... read more
Project Brief (What I Need Designed)
I need a simple stainless steel vacuum chamber and external coil layout for a small countertop water distiller. This is ONLY the mechanical shell and mounting points, no internal electronics or special internals.

Please design:

Main Chamber

Material: SS304

Shape: Vertical cylinder

Outer diameter: 250 mm

Height: 300 mm

Wall thickness: 2 mm

Bottom: flat, welded

Bottom plate:

4 × M6 threaded inserts arranged in a square, centered, on the inside bottom (for a removable heater plate, you just place the holes).

Bottom drain:

1 × 1/4" NPT drain port at the lowest point, oriented downwards.

Inlet (Feed Water Nozzle Port)

Location: Side wall, 80 mm above bottom (centerline).

Connection: 1/4" NPT female threaded boss welded to side wall (I will install my own spray nozzle).

Steam Outlet / Vacuum Port

Location: Top center of the lid.

Connection: 1 × 25 mm OD stub pipe, 50 mm long, vertical.

This will serve as both steam outlet and vacuum connection (to be connected to my external condenser/piping).

External Coil Mounts (Preheat Coil Around Chamber)

Around the outside of the cylinder, please add simple guides/tabs for a 1/4" copper tube coil:

4 vertical “ears” or tabs spaced at 90° around the circumference, with slots or holes so I can tie/clamp a 1/4" tube coil to the outside of the chamber.

Coil height region: from 50 mm above bottom to 250 mm (do not interfere with ports).

Top Lid / Access

Design the top as a removable lid:

Either a clamped flange or bolt ring.

Include a circumferential groove or flat for an O‑ring (I will specify seal later).

Lid must seal under light vacuum (~200 mbar absolute).

Steam Path Mount in Lid

On the underside of the lid, directly under the 25 mm outlet, add:

A simple circular flat area (about 60 mm diameter) with 4× M4 through holes around it, 90° apart, on a 40 mm pitch circle.

This is for mounting my internal insert (you don’t design the insert, just the mounting pattern).

Supports / Feet

Add 3 or 4 simple short legs or base pads so the chamber stands stable on a flat surface.

Total unit height including feet: roughly 320–340 mm.

Deliverables

3D model: STEP (.step) and native file (SolidWorks / Fusion / Inventor).

2D manufacturing drawings (PDF + DWG/DXF) with all key dimensions, tolerances suitable for sheet metal/fabrication.

Exploded view or simple assembly drawing showing lid, body, and coil mounts.

Notes

Treat all internals as generic: no need to design heaters, coils, or special internals.

Design for ease of fabrication by a typical stainless steel shop.

This is for vacuum distillation, so avoid sharp internal corners where stress may concentrate; use reasonable fillets. read less

Things to know

Job location

Remote

Work location

Job skill level

Intermediate

Skill Level

Job rate

$100

Fixed-rate (USD)

Job type

Part-time

Job type

Job length

Under 1-month

Job duration

Areas of expertise

2D CAD Design 2D CAD Drawings

Job categories

3D Modeling

About the client

Payment ready

Nigeria (10:26 am)

Posted

Active

Job activity

37 Applicants

0 interviews in progress

Similar jobs

size changes

Remote - Posted
i want this file in 35mm size with weight of 4.5G and other diesign and name will be same no change is required
3D Jewelry Rendering 3D Modeling Product Engineering Services
View job

Need a Dynamo script for QTO/Schedules in Civil 3D.

Remote - Posted
Job Requirement / Scope of Work Civil 3D / Dynamo Programmer – Automated QTO Extraction and Reporting Tool Develop a Dynamo script for Autodesk Civil 3D that automates t...
Civil Drafting Services 3D Design Services 3D Modeling
View job

CAD designer needed to model 3D consumer product

Remote - Posted
Need to design South Indian style closed stone setting necklace,jhumka,bangles. Stone measurements and drawing will be provided.
3D Modeling 3D Design Services Engineering Design
View job

SolidWorks 2026 FEA Analysis

Remote - Posted
SOLIDWORKS 2026 FEA simulation analysis needed on bolted structural assembly model. Model is complete less fasteners. This is a project to project need. Turnaround is A.S.A....
FEA Finite Element Analysis 3D Design Services 3D Modeling
View job

Technical concept illustration — subscale composite launch vehicle interstage test article

Remote - Posted
We need a single illustrative image (not a diagram) for a research funding submission, to be used publicly in web articles. Minimum 1920×1080px, 16:9 aspect ratio. Subject:...
Concept Design 3D Rendering Services 3D Modeling Aerospace Engineering
View job

Mechanical/Industrial Engineer for Production-Ready 2d/3d Drawings

Remote - Posted
We are seeking a skilled Mechanical or Industrial Engineer to join our team and produce high-quality, production-ready 3D and 2D technical drawings. The ideal candidate will b...
Mechanical Engineering 3D Design Services 3D Modeling
View job

How it works

Find hourly jobs

Find hourly jobs

Top rated experts are regularly hired for hourly jobs & ongoing client work.
Fixed-rate jobs

Fixed-rate jobs

Experts can browse & apply to fixed-rate work & quote on a flat-rate basis.
Design contests

Design contests

Experts build a reputation and earn prizes by participating in design challenges.

About Cad Crowd

4.9/5.0

(Our client satisfaction)

G2 2022

Spring high performer

222,210

global members

33,595

projects delivered to clients


Trusted by
US Army Corps of Engineers
Tiffany
BCG
Target
KPMG
Xprize

Find freelance & remote jobs

Your next big opportunity is just a click away. Create a free profile and start finding work tailored to your skills.