Remote
Work location
Mobile CCTV Tower Trailer Ended
About the job
we aim to mount a telescopic mast and on the top of this mount a few cameras and which will be placed along a pipeline and periodically moved based on the work progress. They will be solar powered and so will have a control box with batteries at the bottom with controls and panels on the box/ skid. What we are needing is a design that we can then use to have the units built in Saudi but we will need obviously a design that is strong enough for the job.
A one-time project for the design of a road legal trailer to mount a telescopic mast and control box/ batteries and solar panels (items will be my supply) In a lowered position the mast will be 1.4 mtrs and when raised will be 5mtrs. Maximum weight at the top will be 30kgs. Below are a few scribblings that I did earlier and then also is what I could see the trailer looking like and also an image of what I would like to to be like. Dimensions need to within road legal limits and so around 1.75mtrs wide and up to 3mtrs in length. As per the image the trailer needs to have the mast and control box secured in a frame which could also be removable if needed. Lifting points on the frame and trailer bed and also forklift pockets on the frame that could act as stiffening for the mast in addition to bracing from the frame to the mast. As per the image I would require outriggers. Either on the frame or trailer for satbility when the mast is raised
The wheels/ suspension ideally to be single axis with leaf springs however twin axis... read more
A one-time project for the design of a road legal trailer to mount a telescopic mast and control box/ batteries and solar panels (items will be my supply) In a lowered position the mast will be 1.4 mtrs and when raised will be 5mtrs. Maximum weight at the top will be 30kgs. Below are a few scribblings that I did earlier and then also is what I could see the trailer looking like and also an image of what I would like to to be like. Dimensions need to within road legal limits and so around 1.75mtrs wide and up to 3mtrs in length. As per the image the trailer needs to have the mast and control box secured in a frame which could also be removable if needed. Lifting points on the frame and trailer bed and also forklift pockets on the frame that could act as stiffening for the mast in addition to bracing from the frame to the mast. As per the image I would require outriggers. Either on the frame or trailer for satbility when the mast is raised
The wheels/ suspension ideally to be single axis with leaf springs however twin axis... read more
we aim to mount a telescopic mast and on the top of this mount a few cameras and which will be placed along a pipeline and periodically moved based on the work progress. They will be solar powered and so will have a control box with batteries at the bottom with controls and panels on the box/ skid. What we are needing is a design that we can then use to have the units built in Saudi but we will need obviously a design that is strong enough for the job.
A one-time project for the design of a road legal trailer to mount a telescopic mast and control box/ batteries and solar panels (items will be my supply) In a lowered position the mast will be 1.4 mtrs and when raised will be 5mtrs. Maximum weight at the top will be 30kgs. Below are a few scribblings that I did earlier and then also is what I could see the trailer looking like and also an image of what I would like to to be like. Dimensions need to within road legal limits and so around 1.75mtrs wide and up to 3mtrs in length. As per the image the trailer needs to have the mast and control box secured in a frame which could also be removable if needed. Lifting points on the frame and trailer bed and also forklift pockets on the frame that could act as stiffening for the mast in addition to bracing from the frame to the mast. As per the image I would require outriggers. Either on the frame or trailer for satbility when the mast is raised
The wheels/ suspension ideally to be single axis with leaf springs however twin axis acceptable if necessary
Dimensions- Needs to be road legal so sizes I suppose around 1.75mtrs wide by 3mtrs long?
Materials- Steel. We will then either have it galvanised or blasted and painted
Placement environment- For road use and then placement off road along pipeline fabrication or placed on a construction site or even a marine barge (offshore) read less
A one-time project for the design of a road legal trailer to mount a telescopic mast and control box/ batteries and solar panels (items will be my supply) In a lowered position the mast will be 1.4 mtrs and when raised will be 5mtrs. Maximum weight at the top will be 30kgs. Below are a few scribblings that I did earlier and then also is what I could see the trailer looking like and also an image of what I would like to to be like. Dimensions need to within road legal limits and so around 1.75mtrs wide and up to 3mtrs in length. As per the image the trailer needs to have the mast and control box secured in a frame which could also be removable if needed. Lifting points on the frame and trailer bed and also forklift pockets on the frame that could act as stiffening for the mast in addition to bracing from the frame to the mast. As per the image I would require outriggers. Either on the frame or trailer for satbility when the mast is raised
The wheels/ suspension ideally to be single axis with leaf springs however twin axis acceptable if necessary
Dimensions- Needs to be road legal so sizes I suppose around 1.75mtrs wide by 3mtrs long?
Materials- Steel. We will then either have it galvanised or blasted and painted
Placement environment- For road use and then placement off road along pipeline fabrication or placed on a construction site or even a marine barge (offshore) read less
we aim to mount a telescopic mast and on the top of this mount a few cameras and which will be placed along a pipeline and periodically moved based on the work progress. They will be solar powered and so will have a control box with batteries at the bottom with controls and panels on the box/ skid. What we are needing is a design that we can then use to have the units built in Saudi but we will ne...
read more
we aim to mount a telescopic mast and on the top of this mount a few cameras and which will be placed along a pipeline and periodically moved based on the work progress. They will be solar powered and so will have a control box with batteries at the bottom with controls and panels on the box/ skid. What we are needing is a design that we can then use to have the units built in Saudi but we will need obviously a design that is strong enough for the job.
A one-time project for the design of a road legal trailer to mount a telescopic mast and control box/ batteries and solar panels (items will be my supply) In a lowered position the mast will be 1.4 mtrs and when raised will be 5mtrs. Maximum weight at the top will be 30kgs. Below are a few scribblings that I did earlier and then also is what I could see the trailer looking like and also an image of what I would like to to be like. Dimensions need to within road legal limits and so around 1.75mtrs wide and up to 3mtrs in length. As per the image the trailer needs to have the mast and control box secured in a frame which could also be removable if needed. Lifting points on the frame and trailer bed and also forklift pockets on the frame that could act as stiffening for the mast in addition to bracing from the frame to the mast. As per the image I would require outriggers. Either on the frame or trailer for satbility when the mast is raised
The wheels/ suspension ideally to be single axis with leaf springs however twin axis acceptable if necessary
Dimensions- Needs to be road legal so sizes I suppose around 1.75mtrs wide by 3mtrs long?
Materials- Steel. We will then either have it galvanised or blasted and painted
Placement environment- For road use and then placement off road along pipeline fabrication or placed on a construction site or even a marine barge (offshore) read less
A one-time project for the design of a road legal trailer to mount a telescopic mast and control box/ batteries and solar panels (items will be my supply) In a lowered position the mast will be 1.4 mtrs and when raised will be 5mtrs. Maximum weight at the top will be 30kgs. Below are a few scribblings that I did earlier and then also is what I could see the trailer looking like and also an image of what I would like to to be like. Dimensions need to within road legal limits and so around 1.75mtrs wide and up to 3mtrs in length. As per the image the trailer needs to have the mast and control box secured in a frame which could also be removable if needed. Lifting points on the frame and trailer bed and also forklift pockets on the frame that could act as stiffening for the mast in addition to bracing from the frame to the mast. As per the image I would require outriggers. Either on the frame or trailer for satbility when the mast is raised
The wheels/ suspension ideally to be single axis with leaf springs however twin axis acceptable if necessary
Dimensions- Needs to be road legal so sizes I suppose around 1.75mtrs wide by 3mtrs long?
Materials- Steel. We will then either have it galvanised or blasted and painted
Placement environment- For road use and then placement off road along pipeline fabrication or placed on a construction site or even a marine barge (offshore) read less
Things to know
Expert
Skill Level
Open budget
Fixed-rate
Part-time
Job type
Under 1-month
Job duration
Areas of expertise
2D & 3D CAD Drawings
Job categories
2D CAD Design Services
About the client
Payment ready
Bahrain (12:02 am)
Posted
Active
Job activity
20 Applicants
3 interviews in progress
7 unanswered invites
Similar jobs
Simple Injection Mold for a mini computer case inspired in BMO.
Remote - Posted
I need a plastic injection mold for saturady 23/05/2026 20:00 CEST. Only requirements are:
- 3D models in Solid Works 2022 of plates, inserts, cooling, injection and ejection...
SolidWorks Design Services
Injection Molding Design
3D Modeling
2D CAD Design Services
2D CAD Drafting Services
View job
2d art for a laser cut gate design
Remote - Posted
Hi
I'm after a gate design. The customer knows what they want mostly. Its a main gate, 3 panels approximately 1366 x 900 with the drawing across the 3 panels. I have attache...
2D CAD Design Services
3D Modeling
3D Design Services
View job
Cad drawing
Remote - Posted
Cad drawing for furnace and other laboratory equipments
2D CAD Design Services
3D Modeling
3D Design Services
View job
Remote Mozaik Cabinet Drafter Translator
Remote - Posted
• Convert approved designs into production-ready cabinet drawings
• Prepare Mozaik files for CNC manufacturing
• Generate cutlists, labels, and nesting sheets
• Review d...
2D CAD Drafting Services
2D CAD Design Services
3D Modeling
View job
Interior Design in Rayon
Remote - Posted
I am looking for a designer who is familiar with Rayon Design. I need to create interior design concept sketches for a luxury custom home.
Examples of the theme as well as...
2D CAD Design Services
Interior Design
ArchiCAD Design Services
View job
SPMT + Blade Lifter in BLENDER for industrial uses - exact - bottleneck - follow path - simulations
Remote - Posted
Job:
conversion 2D in 3D
scale model = no tolerances! 3,00m = 3,00m!
fully rigged model
all axles are moving 60°
axle lifting possible. Animation / movements of axles dri...
2D CAD Design Services
2D to 3D Conversion Services
Blender 3D Modeling Services
3D Modeling
3D Product Modeling
View job
How it works
Find hourly jobs
Top rated experts are regularly hired for hourly jobs & ongoing client work.
Fixed-rate jobs
Experts can browse & apply to fixed-rate work & quote on a flat-rate basis.
Design contests
Experts build a reputation and earn prizes by participating in design challenges.
About Cad Crowd
4.9/5.0
(Our client satisfaction)
G2 2022
Spring high performer
192,852
global members
32,712
projects delivered to clients
Trusted by
