RF engineer Ended

About the job

We are looking for an experienced Senior RF Engineer with 6+ years of hands-on experience in RF system design, wireless communication, RF testing, antenna integration, RF troubleshooting, and validation.
The candidate will be responsible for developing, testing, and optimizing RF and wireless communication systems, working closely with hardware, embedded firmware, and system engineering teams.
Key Responsibilities
Design, develop, test, and validate RF and wireless communication systems.
Work with RF transceivers, RF modules, amplifiers, filters, antennas, connectors, and RF front-end circuits.
Configure and test wireless technologies such as LoRa/LoRaWAN, BLE, Wi-Fi, Sub-GHz, ISM-band, and other RF communication systems.
Perform RF link testing, range testing, sensitivity testing, transmit-power measurements, and communication reliability testing.
Analyze RF performance including TX power, RX sensitivity, frequency stability, bandwidth, RSSI, SNR, and link budget.
Perform antenna selection, integration, matching, and RF performance validation.
Troubleshoot RF communication failures at the module, PCB, antenna, and system levels.
Perform RF measurements using equipment such as spectrum analyzer, signal generator, oscilloscope, power meter, VNA, and RF test equipment.
Analyze RF schematics and PCB layouts for proper RF routing, grounding, impedance control, shielding, and component placement.
Work with RF transmission lines and controlled-impedan... read more
We are looking for an experienced Senior RF Engineer with 6+ years of hands-on experience in RF system design, wireless communication, RF testing, antenna integration, RF troubleshooting, and validation.
The candidate will be responsible for developing, testing, and optimizing RF and wireless communication systems, working closely with hardware, embedded firmware, and system engineering teams.
Key Responsibilities
Design, develop, test, and validate RF and wireless communication systems.
Work with RF transceivers, RF modules, amplifiers, filters, antennas, connectors, and RF front-end circuits.
Configure and test wireless technologies such as LoRa/LoRaWAN, BLE, Wi-Fi, Sub-GHz, ISM-band, and other RF communication systems.
Perform RF link testing, range testing, sensitivity testing, transmit-power measurements, and communication reliability testing.
Analyze RF performance including TX power, RX sensitivity, frequency stability, bandwidth, RSSI, SNR, and link budget.
Perform antenna selection, integration, matching, and RF performance validation.
Troubleshoot RF communication failures at the module, PCB, antenna, and system levels.
Perform RF measurements using equipment such as spectrum analyzer, signal generator, oscilloscope, power meter, VNA, and RF test equipment.
Analyze RF schematics and PCB layouts for proper RF routing, grounding, impedance control, shielding, and component placement.
Work with RF transmission lines and controlled-impedance PCB traces.
Support RF matching-network design and tuning.
Perform RF testing in both laboratory and field environments.
Conduct range and line-of-sight testing for wireless systems.
Investigate interference, noise, signal degradation, and communication dropouts.
Perform RF validation and prepare test procedures, test reports, and technical documentation.
Collaborate with embedded firmware engineers for RF driver, transceiver configuration, register-level settings, and communication testing.
Support hardware bring-up and integration of RF modules with MCUs and embedded systems.
Review RF-related schematics, PCB layouts, datasheets, application notes, and reference designs.
Support EMI/EMC testing and RF regulatory compliance.
Work with PCB and hardware teams to improve RF performance and resolve design issues.
Required Technical Skills
4+ years of experience in RF / Wireless Engineering.
Strong understanding of RF fundamentals and wireless communication principles.
Hands-on experience with RF transceivers and wireless modules.
Experience with LoRa/LoRaWAN, BLE, Wi-Fi, Sub-GHz, or similar wireless technologies.
Knowledge of RF propagation, link budget, TX power, RX sensitivity, RSSI, SNR, frequency, bandwidth, and modulation.
Understanding of RF PCB layout, controlled impedance, grounding, shielding, and RF signal routing.
Experience with antenna selection, integration, testing, and tuning.
Hands-on experience with spectrum analyzer, VNA, signal generator, power meter, oscilloscope, and other RF test equipment.
Ability to analyze RF schematics, PCB layouts, datasheets, and reference designs.
Knowledge of SPI, UART, I2C, and other interfaces used for RF transceiver configuration.
Good understanding of embedded systems and MCU–RF module integration.
Strong troubleshooting and root-cause analysis skills.
Preferred Experience
SX1262 / SX127x / Semtech LoRa experience.
RF power amplifier and LNA integration.
Antenna matching and tuning.
RF filter and front-end design.
RF link-budget calculations.
Long-range wireless communication testing.
Wireless sensor networks and IoT systems.
Experience with industrial, automotive, aerospace, defense, or telemetry systems.
Experience with RF regulatory standards and EMI/EMC compliance testing.
Core Expertise
RF System Design | Wireless Communication | LoRa/LoRaWAN | BLE | Wi-Fi | Sub-GHz | RF Transceivers | Antenna Integration | RF Testing | TX/RX Testing | Link Budget | RSSI | SNR | Spectrum Analyzer | VNA | Signal Generator | RF PCB Layout | Impedance Control | RF Debugging | EMI/EMC | Embedded RF Systems read less
We are looking for an experienced Senior RF Engineer with 6+ years of hands-on experience in RF system design, wireless communication, RF testing, antenna integration, RF troubleshooting, and validation.
The candidate will be responsible for developing, testing, and optimizing RF and wireless communication systems, working closely with hardware, embedded firmware, and system engineering teams.
K... read more
We are looking for an experienced Senior RF Engineer with 6+ years of hands-on experience in RF system design, wireless communication, RF testing, antenna integration, RF troubleshooting, and validation.
The candidate will be responsible for developing, testing, and optimizing RF and wireless communication systems, working closely with hardware, embedded firmware, and system engineering teams.
Key Responsibilities
Design, develop, test, and validate RF and wireless communication systems.
Work with RF transceivers, RF modules, amplifiers, filters, antennas, connectors, and RF front-end circuits.
Configure and test wireless technologies such as LoRa/LoRaWAN, BLE, Wi-Fi, Sub-GHz, ISM-band, and other RF communication systems.
Perform RF link testing, range testing, sensitivity testing, transmit-power measurements, and communication reliability testing.
Analyze RF performance including TX power, RX sensitivity, frequency stability, bandwidth, RSSI, SNR, and link budget.
Perform antenna selection, integration, matching, and RF performance validation.
Troubleshoot RF communication failures at the module, PCB, antenna, and system levels.
Perform RF measurements using equipment such as spectrum analyzer, signal generator, oscilloscope, power meter, VNA, and RF test equipment.
Analyze RF schematics and PCB layouts for proper RF routing, grounding, impedance control, shielding, and component placement.
Work with RF transmission lines and controlled-impedance PCB traces.
Support RF matching-network design and tuning.
Perform RF testing in both laboratory and field environments.
Conduct range and line-of-sight testing for wireless systems.
Investigate interference, noise, signal degradation, and communication dropouts.
Perform RF validation and prepare test procedures, test reports, and technical documentation.
Collaborate with embedded firmware engineers for RF driver, transceiver configuration, register-level settings, and communication testing.
Support hardware bring-up and integration of RF modules with MCUs and embedded systems.
Review RF-related schematics, PCB layouts, datasheets, application notes, and reference designs.
Support EMI/EMC testing and RF regulatory compliance.
Work with PCB and hardware teams to improve RF performance and resolve design issues.
Required Technical Skills
4+ years of experience in RF / Wireless Engineering.
Strong understanding of RF fundamentals and wireless communication principles.
Hands-on experience with RF transceivers and wireless modules.
Experience with LoRa/LoRaWAN, BLE, Wi-Fi, Sub-GHz, or similar wireless technologies.
Knowledge of RF propagation, link budget, TX power, RX sensitivity, RSSI, SNR, frequency, bandwidth, and modulation.
Understanding of RF PCB layout, controlled impedance, grounding, shielding, and RF signal routing.
Experience with antenna selection, integration, testing, and tuning.
Hands-on experience with spectrum analyzer, VNA, signal generator, power meter, oscilloscope, and other RF test equipment.
Ability to analyze RF schematics, PCB layouts, datasheets, and reference designs.
Knowledge of SPI, UART, I2C, and other interfaces used for RF transceiver configuration.
Good understanding of embedded systems and MCU–RF module integration.
Strong troubleshooting and root-cause analysis skills.
Preferred Experience
SX1262 / SX127x / Semtech LoRa experience.
RF power amplifier and LNA integration.
Antenna matching and tuning.
RF filter and front-end design.
RF link-budget calculations.
Long-range wireless communication testing.
Wireless sensor networks and IoT systems.
Experience with industrial, automotive, aerospace, defense, or telemetry systems.
Experience with RF regulatory standards and EMI/EMC compliance testing.
Core Expertise
RF System Design | Wireless Communication | LoRa/LoRaWAN | BLE | Wi-Fi | Sub-GHz | RF Transceivers | Antenna Integration | RF Testing | TX/RX Testing | Link Budget | RSSI | SNR | Spectrum Analyzer | VNA | Signal Generator | RF PCB Layout | Impedance Control | RF Debugging | EMI/EMC | Embedded RF Systems read less

Things to know

Job location

Remote

Work location

Job skill level

Expert

Skill Level

Job rate

Open budget

Fixed-rate

Job type

Part-time

Job type

Job length

Under 1-month

Job duration

Areas of expertise

Altium PCB Aluminum CAD Design Schematic design +2 more

Job categories

Radio Frequency Engineering and Design Services 3D Design Services 3D Modeling

About the client

Payment not ready

United Arab Emirates (10:40 pm)

Posted

Active

Job activity

13 Applicants

0 interviews in progress

Similar jobs

Need a Dynamo script for QTO/Schedules in Civil 3D.

Remote - Posted
Job Requirement / Scope of Work Civil 3D / Dynamo Programmer – Automated QTO Extraction and Reporting Tool Develop a Dynamo script for Autodesk Civil 3D that automates t...
Civil Drafting Services 3D Design Services 3D Modeling
View job

CAD designer needed to model 3D consumer product

Remote - Posted
Need to design South Indian style closed stone setting necklace,jhumka,bangles. Stone measurements and drawing will be provided.
3D Modeling 3D Design Services Engineering Design
View job

SCAN TO 3D SOLIDWORKS DESIGNER

Remote - Posted
Have scans to be imported into SolidWorks for design editing
3D Scan to CAD Service 3D CAD Translation Services 3D Design Services
View job

SolidWorks 2026 FEA Analysis

Remote - Posted
SOLIDWORKS 2026 FEA simulation analysis needed on bolted structural assembly model. Model is complete less fasteners. This is a project to project need. Turnaround is A.S.A....
FEA Finite Element Analysis 3D Design Services 3D Modeling
View job

Multi-Axis CNC Programming - SolidCAM Preferred

United States - Posted
Looking for a candidate that could work on-site in Bethlehem, PA and help transform cutting edge designs into programs for multi-axis milling applications. Team member could i...
CNC Programming SolidWorks Design Services 3D Design Services
View job

Technical concept illustration — subscale composite launch vehicle interstage test article

Remote - Posted
We need a single illustrative image (not a diagram) for a research funding submission, to be used publicly in web articles. Minimum 1920×1080px, 16:9 aspect ratio. Subject:...
Concept Design 3D Rendering Services 3D Modeling Aerospace Engineering
View job

How it works

Find hourly jobs

Find hourly jobs

Top rated experts are regularly hired for hourly jobs & ongoing client work.
Fixed-rate jobs

Fixed-rate jobs

Experts can browse & apply to fixed-rate work & quote on a flat-rate basis.
Design contests

Design contests

Experts build a reputation and earn prizes by participating in design challenges.

About Cad Crowd

4.9/5.0

(Our client satisfaction)

G2 2022

Spring high performer

222,104

global members

33,595

projects delivered to clients


Trusted by
US Army Corps of Engineers
Tiffany
BCG
Target
KPMG
Xprize

Find freelance & remote jobs

Your next big opportunity is just a click away. Create a free profile and start finding work tailored to your skills.