Remote
Work location
Fastener Reverse Engineer and Spec Sheet Design Ended
About the job
I am looking for someone with fastener knowledge in metals and spec/technical sheet creation for manufacturing with the ability to provide necessary files/drawings to send to global manufacturers for quotes.
-Define Material specification. Zamac 3 Body with Zinc plated or Carbon Cone
-Make sure the drawing tolerances are correct particularly in relation to any critical dimensions, these should be highlighted on the drawing. Always better to try and manufacture within the customers requirements so that nothing is made out of spec.
-State how the manufacturer will measure the parts. Are they going to do SPC on them. This gives a good record of dimensions and also allows for Control Limits and Specification Limits with the abilitity to view the charts/data.
-Unsure if this product is heat treated. If so, we need wording onspecification for this and how are they confirming batch hardness levels.
-Verify if the cone is plated. Again, important to have an agreed specification for adhesion of plating and thickness. This should be covered in the ASTM Standard. Also, important to know is the material/plating process susceptible to hydrogen embrittlement.
-Are they carrying out camera inspection on the final parts and if necessary.
-State typical agreed acceptable and unacceptable defects
-Verify all the ASTM standards that cover the process involved.
-Be able to work with testing agencies and manufacturer to achieve proper ratings. These should already be pa... read more
-Define Material specification. Zamac 3 Body with Zinc plated or Carbon Cone
-Make sure the drawing tolerances are correct particularly in relation to any critical dimensions, these should be highlighted on the drawing. Always better to try and manufacture within the customers requirements so that nothing is made out of spec.
-State how the manufacturer will measure the parts. Are they going to do SPC on them. This gives a good record of dimensions and also allows for Control Limits and Specification Limits with the abilitity to view the charts/data.
-Unsure if this product is heat treated. If so, we need wording onspecification for this and how are they confirming batch hardness levels.
-Verify if the cone is plated. Again, important to have an agreed specification for adhesion of plating and thickness. This should be covered in the ASTM Standard. Also, important to know is the material/plating process susceptible to hydrogen embrittlement.
-Are they carrying out camera inspection on the final parts and if necessary.
-State typical agreed acceptable and unacceptable defects
-Verify all the ASTM standards that cover the process involved.
-Be able to work with testing agencies and manufacturer to achieve proper ratings. These should already be pa... read more
I am looking for someone with fastener knowledge in metals and spec/technical sheet creation for manufacturing with the ability to provide necessary files/drawings to send to global manufacturers for quotes.
-Define Material specification. Zamac 3 Body with Zinc plated or Carbon Cone
-Make sure the drawing tolerances are correct particularly in relation to any critical dimensions, these should be highlighted on the drawing. Always better to try and manufacture within the customers requirements so that nothing is made out of spec.
-State how the manufacturer will measure the parts. Are they going to do SPC on them. This gives a good record of dimensions and also allows for Control Limits and Specification Limits with the abilitity to view the charts/data.
-Unsure if this product is heat treated. If so, we need wording onspecification for this and how are they confirming batch hardness levels.
-Verify if the cone is plated. Again, important to have an agreed specification for adhesion of plating and thickness. This should be covered in the ASTM Standard. Also, important to know is the material/plating process susceptible to hydrogen embrittlement.
-Are they carrying out camera inspection on the final parts and if necessary.
-State typical agreed acceptable and unacceptable defects
-Verify all the ASTM standards that cover the process involved.
-Be able to work with testing agencies and manufacturer to achieve proper ratings. These should already be part of the manufacturer's resposibility so it's mainly some communication here.
Should this job stay on budget and in good time, we will continue to work with whomever can deliver and communicate as there are more items already waiting to be developed. We will send samples to help create the package.
Looking forward to developing a relationship with you and growing our businesses together! read less
-Define Material specification. Zamac 3 Body with Zinc plated or Carbon Cone
-Make sure the drawing tolerances are correct particularly in relation to any critical dimensions, these should be highlighted on the drawing. Always better to try and manufacture within the customers requirements so that nothing is made out of spec.
-State how the manufacturer will measure the parts. Are they going to do SPC on them. This gives a good record of dimensions and also allows for Control Limits and Specification Limits with the abilitity to view the charts/data.
-Unsure if this product is heat treated. If so, we need wording onspecification for this and how are they confirming batch hardness levels.
-Verify if the cone is plated. Again, important to have an agreed specification for adhesion of plating and thickness. This should be covered in the ASTM Standard. Also, important to know is the material/plating process susceptible to hydrogen embrittlement.
-Are they carrying out camera inspection on the final parts and if necessary.
-State typical agreed acceptable and unacceptable defects
-Verify all the ASTM standards that cover the process involved.
-Be able to work with testing agencies and manufacturer to achieve proper ratings. These should already be part of the manufacturer's resposibility so it's mainly some communication here.
Should this job stay on budget and in good time, we will continue to work with whomever can deliver and communicate as there are more items already waiting to be developed. We will send samples to help create the package.
Looking forward to developing a relationship with you and growing our businesses together! read less
I am looking for someone with fastener knowledge in metals and spec/technical sheet creation for manufacturing with the ability to provide necessary files/drawings to send to global manufacturers for quotes.
-Define Material specification. Zamac 3 Body with Zinc plated or Carbon Cone
-Make sure the drawing tolerances are correct particularly in relation to any critical dimensions, these shou... read more
-Define Material specification. Zamac 3 Body with Zinc plated or Carbon Cone
-Make sure the drawing tolerances are correct particularly in relation to any critical dimensions, these shou... read more
I am looking for someone with fastener knowledge in metals and spec/technical sheet creation for manufacturing with the ability to provide necessary files/drawings to send to global manufacturers for quotes.
-Define Material specification. Zamac 3 Body with Zinc plated or Carbon Cone
-Make sure the drawing tolerances are correct particularly in relation to any critical dimensions, these should be highlighted on the drawing. Always better to try and manufacture within the customers requirements so that nothing is made out of spec.
-State how the manufacturer will measure the parts. Are they going to do SPC on them. This gives a good record of dimensions and also allows for Control Limits and Specification Limits with the abilitity to view the charts/data.
-Unsure if this product is heat treated. If so, we need wording onspecification for this and how are they confirming batch hardness levels.
-Verify if the cone is plated. Again, important to have an agreed specification for adhesion of plating and thickness. This should be covered in the ASTM Standard. Also, important to know is the material/plating process susceptible to hydrogen embrittlement.
-Are they carrying out camera inspection on the final parts and if necessary.
-State typical agreed acceptable and unacceptable defects
-Verify all the ASTM standards that cover the process involved.
-Be able to work with testing agencies and manufacturer to achieve proper ratings. These should already be part of the manufacturer's resposibility so it's mainly some communication here.
Should this job stay on budget and in good time, we will continue to work with whomever can deliver and communicate as there are more items already waiting to be developed. We will send samples to help create the package.
Looking forward to developing a relationship with you and growing our businesses together! read less
-Define Material specification. Zamac 3 Body with Zinc plated or Carbon Cone
-Make sure the drawing tolerances are correct particularly in relation to any critical dimensions, these should be highlighted on the drawing. Always better to try and manufacture within the customers requirements so that nothing is made out of spec.
-State how the manufacturer will measure the parts. Are they going to do SPC on them. This gives a good record of dimensions and also allows for Control Limits and Specification Limits with the abilitity to view the charts/data.
-Unsure if this product is heat treated. If so, we need wording onspecification for this and how are they confirming batch hardness levels.
-Verify if the cone is plated. Again, important to have an agreed specification for adhesion of plating and thickness. This should be covered in the ASTM Standard. Also, important to know is the material/plating process susceptible to hydrogen embrittlement.
-Are they carrying out camera inspection on the final parts and if necessary.
-State typical agreed acceptable and unacceptable defects
-Verify all the ASTM standards that cover the process involved.
-Be able to work with testing agencies and manufacturer to achieve proper ratings. These should already be part of the manufacturer's resposibility so it's mainly some communication here.
Should this job stay on budget and in good time, we will continue to work with whomever can deliver and communicate as there are more items already waiting to be developed. We will send samples to help create the package.
Looking forward to developing a relationship with you and growing our businesses together! read less
Things to know
Any
Skill Level
$10 - $75/hr
Hourly (USD)
Part-time
Job type
Under 1-month
Job duration
Areas of expertise
2D CAD Drawings
3D CAD Drawing
3D Metal Constructions
3D Modeling and Drawings
3D Mold Design
3D PDF Files
3D Part Modeling
+4 more
Job categories
Manufacturing Drawings
3D Modeling
Prototype Tooling
Mold and Die Design Services
+1 more
About the client
Payment ready
United States (06:32 am)
Posted
Active
Job activity
29 Applicants
1 interviews in progress
Similar jobs
CNC Machine Shops Needed – Real Production Machining Data (Fusion 360 CAM)
Remote - Posted
We are looking for CNC machine shops and authorized manufacturing data suppliers who can provide original files from real, previously completed 3-axis CNC milling jobs using A...
Mechanical Design Services
Manufacturing Drawings
CNC Programming
View job
Digital Design
Remote - Posted
To design an Indian Classical Instrument
For mass production purposes
And future upgrades
Industrial Design Services
3D Modeling
3D Design Services
View job
Request for 2D Drawings and 3D CAD Data – Reverse Shoulder Arthroplasty Implant System (Prototype / Engineering Evaluation)
Remote - Posted
We are looking to obtain 2D manufacturing drawings and 3D CAD data for a reverse shoulder arthroplasty implant system, for non-clinical prototype fabrication and engineering e...
Medical Devices Design
3D Design Services
3D Modeling
View job
Furniture Design Needed to assist with Collection
Remote - Posted
We are looking for an experienced furniture designer to collaborate with us throughout the creative design process, from developing initial ideas and concepts through to refin...
Furniture Design
3D Design Services
3D Modeling
View job
Reverse Shoulder Implant – 3D CAD Models and 2D Drawings for Prototyping
Remote - Posted
We are seeking an experienced CAD designer or mechanical engineer to develop 3D CAD models and 2D manufacturing drawings for a reverse shoulder implant prototype.
We have a...
Medical Devices Design
3D Design Services
3D Modeling
View job
Design engineer for facade projects
Remote - Posted
○ Develop accurate shop drawings using Dextall Studio, Revit, and AutoCAD.
○ Ensure designs meet company standards, project requirements, and codes.
○ Prepare and respond to...
Revit Design Services
AutoCAD Drawing Services
Design Engineering Services
AutoCAD Design Services
3D Modeling
View job
How it works
Find hourly jobs
Top rated experts are regularly hired for hourly jobs & ongoing client work.
Fixed-rate jobs
Experts can browse & apply to fixed-rate work & quote on a flat-rate basis.
Design contests
Experts build a reputation and earn prizes by participating in design challenges.
About Cad Crowd
4.9/5.0
(Our client satisfaction)
G2 2022
Spring high performer
216,356
global members
33,565
projects delivered to clients
Trusted by
