Designs by DBARN

For Project: Ecig
#15 BATTERY CASE-6 by DBARN
W/ MINOR CHANGES
more
2013-11-15 14:13:55
#9 BATTERY CASE 5 by DBARN
CAD DWG AND EXPLODED ASSEMBLY
more
2013-10-21 14:09:16
#8 BATTERY CASE-4 by DBARN
BATTERY CASE DWGS AND EXPLODED ASSEMBLY
more
2013-10-17 14:36:10
#7 BATTERY CASE -3 by DBARN
SINGLE BATTERY CASE - ORTHOGRAPHIC DIMENSIONED VIEWS AND SOLID MODEL
more
2013-10-16 14:03:13
#6 BATTERYCASE-2 by DBARN
BATTERY CASE FOR A SINGLE BATTERY WITH DIMS AND SOLIDS
more
2013-10-15 15:50:39
#5 BATTERY CASE by DBARN
BATTERY CASE DESIGN INCLUDING SOLID MODELS AND DIMENSIONS NEEDED FOR PRODUCTION
more
2013-10-15 15:25:00

Discussion

DBARN

Designer

Fri, 15 Nov 2013 14:15:40 +0000
SEE IF THIS IS WHAT YOU'RE AFTER...

Dunha123

Buyer

Fri, 15 Nov 2013 12:35:19 +0000
Hi sorry for just now reply to you but I have been away for 3 weeks on personal business the spring sleeve needs a treading that will screw on to the contact stop to work as a look button to the bottom cap the end cap part is fine just the 502 conection needs an isolation ruber to pass the current straight to the central pin and not to the allend cap. I have allready nominated you.

DBARN

Designer

Mon, 21 Oct 2013 14:12:47 +0000
Sorry about the confusion, I think I'm getting what you are saying. If I don't have it right, please tell me the name of each part by giving me what it actually is and then what I labeled it as, then I can understand which parts are needing editing and also put the correct heading by each.
I'm used to drawing by measuring the parts themselves so I hope these are workable.
Thanks!

Dunha123

Buyer

Sat, 19 Oct 2013 15:05:52 +0000
hi I have attached new picture for the top end cap have a look you will have a full understand of what I want, also put a picture for the activation button for you to have a look the button is alright the way you design just missing the venting hole that you will see on the picture and the sleeve for the spring which is also the locking button needs to have a reverse thread to g o up and down so it can lock the activation button. just these details are missing

Dunha123

Buyer

Wed, 16 Oct 2013 21:24:04 +0000
Perfect just the end cap the top as to have a 510 conection to screw the tank see the photo I posted under the name photo the ruber washer is not needed as the ruber is inside the end cap just preventing the adjustable pin to contact with the rest of the end cap. The spring sleeve as a reverse screw so when it's unscrewed will look the bottom cap so when it's on the pocket will not fire the coil and when screw back up will not unscrew the button of the barrel. And the contact stop will have a hole to vent in case of the battery goes wrong and liberts gas. I will try and see the right measures for the end cap conection. That done the prize is yours. After I will post a contest for the tank it will be nice if you could do that one to.

Dunha123

Buyer

Tue, 15 Oct 2013 22:49:11 +0000
Almost there the end cap as you can see in my photos as a 510 conection and a central pin that will conect the positive pole of the battery to the thank to activate the coil. As to have a ruber or silicone barrier around so it will not pass the current to all the top and that end top will screw on to the tube. The activation button the assembely is correct but the middle ring as a reverse screw to be used as a look button and I need the measurements for all the parts. The battery will sit on the screw and the little pin will conect to the negative pole when pressed. But what you have with these few request is what I need. Let me know if you have any questions.